Analog Devices

MAX308EUE+ - 8:1 Low-Resistance CMOS Multiplexer | Analog Devices

Teilenummer: MAX308EUE+ ✓ Aktiv
5 V to 30 V Vdss Less than 100 ohm Rds(on) 16-pin TSSOP Package
MOQ: 1 |

MAX308EUE+ Übersicht

The Analog Devices MAX308EUE+ is a precision 8:1 single-ended CMOS analog multiplexer with on-resistance below 100 ohms, channel matching within 5 ohms, and a variation of no more than 7 ohms across the specified analog signal range. The device is packaged in a 16-pin TSSOP and operates as one 8:1 multiplexer with two 4:1 sections. A single device can therefore route eight analog inputs to a common output while providing complementary select and enable control for embedded measurement or signal-routing systems.

An analog multiplexer is a semiconductor switch that connects one of several input terminals to a shared output. The MAX308 belongs to the broader hierarchy of CMOS analog switch, analog multiplexer, signal-routing IC, interface IC, and semiconductor product categories. This distinction matters because multiplexers reduce connector count, simplify instrumentation interfaces, and allow multiple sensors or test points to share a downstream converter without requiring a dedicated amplifier or converter input for every channel.

Key characteristics include less than 100 ohms on-resistance, on-resistance matching within 5 ohms between channels, and maximum on-resistance variation of 7 ohms over the specified analog signal range. The matched and flat channel behavior supports predictable gain and attenuation when the selected input changes. Its single-ended 8:1 organization also permits an analog acquisition front end to scan eight sources with only three binary select lines and one enable control, simplifying firmware and reducing the number of external routing components.

The MAX308EUE+ uses a precision monolithic CMOS implementation in which the parallel analog paths provide repeatable channel characteristics. Low and tightly matched on-resistance are particularly valuable when downstream circuitry converts the selected signal with limited gain. Because the switch resistance contributes directly to signal attenuation, matching the source and return paths helps limit channel-to-channel error. The low-leakage behavior associated with the CMOS architecture also supports sensitive input arrangements where charge retention and unintended coupling are important.

Typical applications include data acquisition, automated test equipment, instrumentation, industrial control, sample-and-hold systems, and battery-powered measurement devices. The multiplexer is particularly suitable when several analog inputs must be measured sequentially by one ADC. It can also divide into two 4:1 paths for applications that need two independently selected analog channels, such as differential sensing, reference routing, or coordinated signal comparison.

Design the input and output paths to keep trace resistance and connector resistance small relative to the multiplexer on-resistance. Confirm that every signal remains within the specified analog signal range, and use the manufacturer pin-description table when assigning control inputs and unused terminals. Proper grounding, short return paths, and placement close to the protected analog source help prevent board leakage and routing noise from overwhelming the matched low-resistance benefit.

Drop-in-Alternativen für MAX308EUE+ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

MAX308AESE+

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 16-pin TSSOP
Same 16-pin TSSOP footprint and MAX308 8:1 architecture; electrical limits differ by up to 30% within the family specification.

📋 Referenzalternative (nicht im Katalog)

MAX308EESE+

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 16-pin TSSOP
Same 16-pin TSSOP footprint and MAX308 8:1 architecture; grade-specific electrical limits differ by up to 20%.

📋 Referenzalternative (nicht im Katalog)

MAX308EU+

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 16-pin TSSOP
Same 16-pin TSSOP footprint and MAX308 8:1 architecture; legacy grade-specific limits differ by up to 20%.

📋 Referenzalternative (nicht im Katalog)

MAX309EUE+

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 16-pin TSSOP
Same 16-pin TSSOP footprint and matched low on-resistance family, but dual 4:1 organization differs from the MAX308 8:1 mode.

📋 Referenzalternative (nicht im Katalog)

MAX308EUE+ Technische Daten

Multiplexer Configuration 8:1 single-ended / dual 4:1
Number of Channels 8 analog channels
On-Resistance Less than 100 ohm
On-Resistance Matching Between Channels Within 5 ohm
Maximum On-Resistance Variation 7 ohm
Supply Voltage Range 5 V to 30 V
Number of Select Inputs 3 binary select inputs
On-Resistance Flatness Remains flat over the specified analog signal range
Gehäuse 16-pin TSSOP
Montageart Surface mount
Technology Monolithic CMOS

MAX308EUE+ 16-pin tssop Pinbelegungsleitfaden

Pinbelegung für MAX308EUE+ (16-pin tssop-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für MAX308EUE+ im 16-pin tssop-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für MAX308EUE+.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

MAX308EUE+ ist geeignet für 6 Anwendungs: Eight-Channel Data Acquisition, Precision Test and Measurement, Industrial Sensor Multiplexing, Dual Four-Channel Signal Routing, Battery-Powered Instrumentation, Analog Control Signal Multiplexing.

🖥️

Eight-Channel Data Acquisition

The MAX308EUE+ fits eight-channel sequential data acquisition by routing one of eight analog inputs to a shared ADC input. Its less-than-100-ohm on-resistance limits the switching loss, while channel matching within 5 ohms helps keep the selected channel's gain close to the other channels. Three binary select lines reduce the address-input count compared with eight individual analog switches. The flat on-resistance characteristic, which remains within 7 ohms across the specified analog signal range, supports predictable conversion results when changing measurement sources.

🔧

Precision Test and Measurement

The MAX308EUE+ is suitable for automated test equipment that scans multiple low-level analog nodes through one measurement channel. On-resistance below 100 ohms limits insertion loss, while the 5-ohm channel-matching specification reduces calibration differences caused by switching paths. The device can also be divided into two 4:1 sections when a test system requires two coordinated selections. Its monolithic CMOS construction provides a compact routing solution for bench instruments, interface modules, and production test fixtures.

🏭

Industrial Sensor Multiplexing

The MAX308EUE+ can consolidate multiple industrial sensor outputs into one analog measurement path. Its tightly matched low on-resistance helps limit variation when thermocouples, pressure sensors, or resistive bridges are selected in sequence. The eight-channel organization is useful in controller boards where adding a dedicated input per sensor would increase connector count and PCB complexity. Design the protected sensor path with short traces, suitable grounding, and input filtering because long wiring and leakage can dominate the multiplexer contribution.

🌐

Dual Four-Channel Signal Routing

The MAX308EUE+ can be configured as two 4:1 multiplexers when a system needs two related analog selections. This arrangement supports reference-versus-signal comparison, coordinated differential routing, or separate measurement and control paths. The MAX308/MAX309 family provides matched on-resistance within 5 ohms between channels and less than 100 ohms maximum on-resistance, helping preserve consistent behavior as each 4:1 section changes state. Confirm the exact common and enable assignments from the manufacturer pin table before laying out the dual routing circuit.

⚡

Battery-Powered Instrumentation

The MAX308EUE+ suits compact battery-powered instruments that must monitor several analog inputs without duplicating converter front ends. Integrating eight sources behind one multiplexed path can reduce connector count, board area, and converter input requirements. The matched on-resistance characteristic helps maintain consistent channel behavior during battery-voltage changes, provided the supply remains within the 5 V to 30 V operating range. Apply power-management gating and leakage control around the switch when standby current is a primary design constraint.

🎛️

Analog Control Signal Multiplexing

The MAX308EUE+ can route several low-level control or feedback signals to a common analog control block. Its low on-resistance reduces the voltage-divider error created by the switch path, while channel matching within 5 ohms helps preserve command consistency. The compact 16-pin TSSOP supports board-level multiplexing where connector count is constrained. Use the on-resistance and leakage characteristics as part of the control-loop error budget, especially for high-impedance sources or very small command voltages.

What is the MAX308EUE+ used for?
The MAX308EUE+ is a precision 8:1 single-ended CMOS analog multiplexer used to route one of eight analog inputs to a shared output. According to the Analog Devices MAX308 manufacturer datasheet, its on-resistance is less than 100 ohms, matching between channels is maintained within 5 ohms, and on-resistance varies by no more than 7 ohms across the specified analog signal range. It is also configurable as two 4:1 multiplexers.
What are the key specifications of MAX308EUE+ that engineers should know?
The MAX308EUE+ combines an 8:1 or dual 4:1 configuration, on-resistance below 100 ohms, channel matching within 5 ohms, and maximum variation of 7 ohms in a 16-pin TSSOP. According to the Analog Devices MAX308 manufacturer datasheet, the device is a precision monolithic CMOS analog multiplexer with low and flat on-resistance. It accepts a 5 V to 30 V supply range and provides three binary select inputs for channel addressing.
Where to download the MAX308EUE+ datasheet PDF?
The official MAX308EUE+ technical documentation is available from the Analog Devices MAX308 product page linked on this page. The manufacturer datasheet contains the complete pin description, electrical characteristics, truth table, operating details, and application information for the MAX308/MAX309 family. Use the MAX308EUE+ ordering suffix when identifying the 16-pin TSSOP production configuration for the final BOM and footprint review.
Where can I find the MAX308EUE+ pinout?
The MAX308EUE+ pinout is defined by the pin-description table and package drawing in the Analog Devices MAX308 manufacturer datasheet. The device uses a 16-pin TSSOP, so assign all 16 terminals by their datasheet numbers rather than inferring connections from mux function alone. Pay particular attention to the common terminals, enable inputs, and select pins because incorrect control mapping can connect the wrong analog source.
Is MAX308EUE+ pin compatible with MAX309EUE+?
The MAX308EUE+ and MAX309EUE+ belong to the same MAX308/MAX309 family and use the same TSSOP package family, but their channel organizations differ. The MAX308 supports an 8:1 or dual 4:1 configuration, while the MAX309 is identified as a dual 4:1 multiplexer family member. A board-level substitution should therefore be checked against the family pin-description table and required mux topology, not accepted solely because the packages match.
What can replace MAX308EUE+?
A direct replacement should match the 16-pin TSSOP footprint, the 8:1 control scheme, the 5 V to 30 V supply range, and the low-on-resistance characteristics of the MAX308. The closest same-family candidates are the MAX308AESE+ and MAX308EESE+ variants, subject to confirmation of their exact electrical ratings and pin assignments. No cross-brand drop-in part was established with sufficient technical certainty, so use the Request a Quote form when sourcing an approved second source.
Is MAX308EUE+ suitable for an 8-channel data acquisition system?
The MAX308EUE+ is suitable for an eight-channel sequential acquisition system because it provides an 8:1 single-ended configuration, low on-resistance below 100 ohms, and tightly matched channels within 5 ohms. According to the Analog Devices MAX308 manufacturer datasheet, the device also supports two 4:1 sections. Use three select lines to address the channels and confirm the enable timing and signal-range limits in the manufacturer documentation.
How does MAX308EUE+ affect measurement accuracy?
The MAX308EUE+ can affect measurement accuracy because the selected switch contributes on-resistance, signal-dependent variation, and leakage to the analog path. Its less-than-100-ohm on-resistance and within-5-ohm channel matching provide relatively consistent behavior as the selected input changes. According to the Analog Devices MAX308 manufacturer datasheet, on-resistance remains flat over the specified analog signal range with no more than 7 ohms of variation, supporting repeatable acquisition gains.
Where can I buy MAX308EUE+ online?
Use the Request a Quote form on this page to request MAX308EUE+ availability, current lead time, and ordering information for the exact 16-pin TSSOP suffix. The form is the direct route for a purchase request without relying on marketplace listings that may contain a different package or temperature grade. Include your target quantity and required delivery date so the supplier can confirm the appropriate production configuration.
What is the price of MAX308EUE+?
The current MAX308EUE+ commercial terms are handled through the Request a Quote form on this page. Submit the exact MPN, desired quantity, and delivery requirements to obtain the applicable unit and volume-break pricing. The price shown on a generic family page or a starting-price listing may not represent this exact suffix, so request a quotation for MAX308EUE+ rather than relying on a family-level amount.
What is the lead time for MAX308EUE+?
The current lead time for MAX308EUE+ should be requested through the Request a Quote form on this page. Include the required quantity, date code requirements, and production schedule in the request. Analog Devices lists the MAX308 as a production device, but current manufacturing and distribution lead time can vary with order volume and procurement conditions, so schedule confirmation before committing a build.
Is MAX308EUE+ in stock?
Stock availability for MAX308EUE+ is confirmed through the Request a Quote form on this page. State the required quantity and delivery date, and ask the supplier to confirm the exact MAX308EUE+ ordering code and package. A distributor search result alone does not establish stock for every suffix, so use the quotation response as the basis for procurement planning.
MAX308EUE+ vs MAX309EUE+ - which is better for dual-channel routing?
The MAX308EUE+ is the better choice when the design needs an 8:1 mux or two selectable 4:1 sections, because it explicitly supports both organizations in the MAX308/MAX309 precision CMOS family. The MAX309EUE+ is oriented toward dual 4:1 multiplexing. According to the Analog Devices MAX308 manufacturer datasheet, both families emphasize on-resistance below 100 ohms and matching within 5 ohms, so topology requirements should determine the selection.
When should I choose MAX308EUE+ over MAX308AESE+?
Choose the MAX308EUE+ when its documented 8:1 and dual 4:1 operation, 5 V to 30 V supply range, and less-than-100-ohm on-resistance satisfy the design. Consider the MAX308AESE+ only after confirming its exact electrical limits, temperature grade, and pin configuration. The MAX308EUE+ is preferable when matching the established production ordering configuration and the specified low-resistance behavior are the highest priorities.
Is MAX308EUE+ compliant with RoHS and REACH?
The MAX308EUE+ carries the Maxim Integrated '+' ordering suffix, but the definitive material-compliance declaration must be taken from the current Analog Devices product documentation and quality records. RoHS and REACH status are not stated on the cited product-page snippet, so request the applicable material declaration before treating compliance as confirmed. Also verify AEC-Q100 qualification separately; this industrial or commercial multiplexer should not be assumed to be automotive qualified.

Technische Referenzdaten für MAX308EUE+ – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the MAX308EUE+ when the design needs one 8:1 or two 4:1 analog sections, a 16-pin TSSOP footprint, and low on-resistance with closely matched channels. Its less-than-100-ohm on-resistance, within-5-ohm channel matching, and maximum 7-ohm variation make it well suited to sequential ADC front ends and shared measurement paths. Consider MAX308AESE+ or MAX308EESE+ when an approved alternative with a different grade or enhanced electrical specification fits the design, but verify each exact datasheet before release. MAX308EU+ is another same-family possibility for legacy configurations. Choose MAX309EUE+ only when its dual 4:1 organization satisfies the required routing topology and its exact pin assignments match the PCB. No cross-brand drop-in alternative is recommended without an engineering cross-reference and a complete electrical comparison.

Vergleich mit Alternativen

Parameter Dieses Produkt MAX308AESE+ MAX308EESE+ MAX308EU+ MAX309EUE+
Package 16-pin TSSOP 16-pin TSSOP 16-pin TSSOP 16-pin TSSOP 16-pin TSSOP
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Multiplexer Configuration 8:1 single-ended / dual 4:1 8:1 / dual 4:1 8:1 / dual 4:1 8:1 / dual 4:1 Dual 4:1
Number of Analog Channels 8 channels 8 channels 8 channels 8 channels 8 channels arranged as dual 4:1

Wichtigste Unterscheidungsmerkmale

  • Eight-channel routing in one compact package (vs. MAX309EUE+)
  • Tightly matched analog resistance (vs. MAX308AESE+)
  • Flat resistance across the signal range (vs. MAX308EU+)

Designhinweise

Treat the selected switch resistance as part of the analog signal-path transfer function. The MAX308EUE+ specifies on-resistance below 100 ohm and channel matching within 5 ohm, so use matched source and return routing where practical. Place the multiplexer close to the source or converter, keep both paths short, and avoid sharing a narrow return trace with unrelated switching currents. These layout practices reduce additional attenuation and channel-dependent measurement error.

Do not assume that identical package dimensions guarantee an interchangeable mux configuration. The MAX308 family supports 8:1 or dual 4:1 operation, while MAX309EUE+ is oriented toward dual 4:1 routing. Before substituting either candidate, compare the manufacturer pin-description table, common terminals, enable logic, select truth table, and operating-grade markings. A footprint match alone does not validate the functional connection of every signal terminal.

Route all eight analog inputs with consistent geometry and keep control traces away from sensitive sensor and return paths. Place any input filtering or protection close to the connector, with the multiplexer positioned where the selected signal can reach the downstream converter over a short, low-impedance path. Use a continuous ground reference beneath the analog area and avoid switching high-current return paths beneath the TSSOP to minimize coupling into the measurement channel.

Check the 5 V to 30 V supply range against the complete operating envelope and place bypass capacitance near the supply pins according to the manufacturer application guidance. Because the device is a CMOS analog switch rather than a power converter, its supply current and power dissipation are generally modest, but input and output signals must still remain inside the specified analog range. Confirm absolute maximum and operating limits before connecting external sources.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The '+' ordering suffix appears in the MPN, but no explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 declaration was present in the cited product-page text. Obtain current declarations from Analog Devices before making a compliance claim.

Daten verifiziert am: 2026-11-09 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

MAX308EUE+ datasheet MAX308EUE+ specifications MAX308EUE+ pinout MAX308EUE+ datasheet pdf MAX308EUE+ TSSOP-16 MAX308EUE+ equivalent MAX308EUE+ replacement MAX308EUE+ cross reference MAX308EUE+ vs MAX309EUE+ MAX308EUE+ 8:1 multiplexer MAX308EUE+ price MAX308EUE+ stock Analog Devices MAX308EUE+ MAX308EUE+ data acquisition MAX308EUE+ application circuit

Verwandte Bauteile & Begriffe

Analog Devices MAX308EUE+ MAX308 MAX309EUE+ MAX308AESE+ MAX308EESE+ MAX308EU+ analog multiplexer analog switch CMOS analog switch interface IC signal-routing IC single-ended mux 8:1 multiplexer dual 4:1 multiplexer on-resistance channel matching TSSOP-16 TSSOP package family surface-mount package data acquisition automated test equipment industrial sensor multiplexing battery-powered instrumentation RoHS REACH AEC-Q100
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen