MAX308EUE+ - 8:1 Low-Resistance CMOS Multiplexer | Analog Devices
料号: MAX308EUE+ ✓ 量产中MAX308EUE+ 概述
An analog multiplexer is a semiconductor switch that connects one of several input terminals to a shared output. The MAX308 belongs to the broader hierarchy of CMOS analog switch, analog multiplexer, signal-routing IC, interface IC, and semiconductor product categories. This distinction matters because multiplexers reduce connector count, simplify instrumentation interfaces, and allow multiple sensors or test points to share a downstream converter without requiring a dedicated amplifier or converter input for every channel.
Key characteristics include less than 100 ohms on-resistance, on-resistance matching within 5 ohms between channels, and maximum on-resistance variation of 7 ohms over the specified analog signal range. The matched and flat channel behavior supports predictable gain and attenuation when the selected input changes. Its single-ended 8:1 organization also permits an analog acquisition front end to scan eight sources with only three binary select lines and one enable control, simplifying firmware and reducing the number of external routing components.
The MAX308EUE+ uses a precision monolithic CMOS implementation in which the parallel analog paths provide repeatable channel characteristics. Low and tightly matched on-resistance are particularly valuable when downstream circuitry converts the selected signal with limited gain. Because the switch resistance contributes directly to signal attenuation, matching the source and return paths helps limit channel-to-channel error. The low-leakage behavior associated with the CMOS architecture also supports sensitive input arrangements where charge retention and unintended coupling are important.
Typical applications include data acquisition, automated test equipment, instrumentation, industrial control, sample-and-hold systems, and battery-powered measurement devices. The multiplexer is particularly suitable when several analog inputs must be measured sequentially by one ADC. It can also divide into two 4:1 paths for applications that need two independently selected analog channels, such as differential sensing, reference routing, or coordinated signal comparison.
Design the input and output paths to keep trace resistance and connector resistance small relative to the multiplexer on-resistance. Confirm that every signal remains within the specified analog signal range, and use the manufacturer pin-description table when assigning control inputs and unused terminals. Proper grounding, short return paths, and placement close to the protected analog source help prevent board leakage and routing noise from overwhelming the matched low-resistance benefit.
直接替换替代料: MAX308EUE+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
MAX308AESE+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX308EESE+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX308EU+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX309EUE+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX308EUE+ 规格参数
| Multiplexer Configuration | 8:1 single-ended / dual 4:1 |
| Number of Channels | 8 analog channels |
| On-Resistance | Less than 100 ohm |
| On-Resistance Matching Between Channels | Within 5 ohm |
| Maximum On-Resistance Variation | 7 ohm |
| Supply Voltage Range | 5 V to 30 V |
| Number of Select Inputs | 3 binary select inputs |
| On-Resistance Flatness | Remains flat over the specified analog signal range |
| 封装 | 16-pin TSSOP |
| 安装类型 | Surface mount |
| Technology | Monolithic CMOS |
MAX308EUE+ 16-pin tssop 引脚配置指南
MAX308EUE+(16-pin tssop 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX308EUE+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX308EUE+ 适用于 6 应用s: Eight-Channel Data Acquisition, Precision Test and Measurement, Industrial Sensor Multiplexing, Dual Four-Channel Signal Routing, Battery-Powered Instrumentation, Analog Control Signal Multiplexing.
Eight-Channel Data Acquisition
The MAX308EUE+ fits eight-channel sequential data acquisition by routing one of eight analog inputs to a shared ADC input. Its less-than-100-ohm on-resistance limits the switching loss, while channel matching within 5 ohms helps keep the selected channel's gain close to the other channels. Three binary select lines reduce the address-input count compared with eight individual analog switches. The flat on-resistance characteristic, which remains within 7 ohms across the specified analog signal range, supports predictable conversion results when changing measurement sources.
推荐
Precision Test and Measurement
The MAX308EUE+ is suitable for automated test equipment that scans multiple low-level analog nodes through one measurement channel. On-resistance below 100 ohms limits insertion loss, while the 5-ohm channel-matching specification reduces calibration differences caused by switching paths. The device can also be divided into two 4:1 sections when a test system requires two coordinated selections. Its monolithic CMOS construction provides a compact routing solution for bench instruments, interface modules, and production test fixtures.
推荐
Industrial Sensor Multiplexing
The MAX308EUE+ can consolidate multiple industrial sensor outputs into one analog measurement path. Its tightly matched low on-resistance helps limit variation when thermocouples, pressure sensors, or resistive bridges are selected in sequence. The eight-channel organization is useful in controller boards where adding a dedicated input per sensor would increase connector count and PCB complexity. Design the protected sensor path with short traces, suitable grounding, and input filtering because long wiring and leakage can dominate the multiplexer contribution.
推荐
Dual Four-Channel Signal Routing
The MAX308EUE+ can be configured as two 4:1 multiplexers when a system needs two related analog selections. This arrangement supports reference-versus-signal comparison, coordinated differential routing, or separate measurement and control paths. The MAX308/MAX309 family provides matched on-resistance within 5 ohms between channels and less than 100 ohms maximum on-resistance, helping preserve consistent behavior as each 4:1 section changes state. Confirm the exact common and enable assignments from the manufacturer pin table before laying out the dual routing circuit.
推荐
Battery-Powered Instrumentation
The MAX308EUE+ suits compact battery-powered instruments that must monitor several analog inputs without duplicating converter front ends. Integrating eight sources behind one multiplexed path can reduce connector count, board area, and converter input requirements. The matched on-resistance characteristic helps maintain consistent channel behavior during battery-voltage changes, provided the supply remains within the 5 V to 30 V operating range. Apply power-management gating and leakage control around the switch when standby current is a primary design constraint.
推荐
Analog Control Signal Multiplexing
The MAX308EUE+ can route several low-level control or feedback signals to a common analog control block. Its low on-resistance reduces the voltage-divider error created by the switch path, while channel matching within 5 ohms helps preserve command consistency. The compact 16-pin TSSOP supports board-level multiplexing where connector count is constrained. Use the on-resistance and leakage characteristics as part of the control-loop error budget, especially for high-impedance sources or very small command voltages.
推荐
推荐产品汇总
工程参考数据: MAX308EUE+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX308AESE+ | MAX308EESE+ | MAX308EU+ | MAX309EUE+ |
|---|---|---|---|---|---|
| Package | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Multiplexer Configuration | 8:1 single-ended / dual 4:1 | 8:1 / dual 4:1 | 8:1 / dual 4:1 | 8:1 / dual 4:1 | Dual 4:1 |
| Number of Analog Channels | 8 channels | 8 channels | 8 channels | 8 channels | 8 channels arranged as dual 4:1 |
关键差异点
- Eight-channel routing in one compact package (对比 MAX309EUE+)
- Tightly matched analog resistance (对比 MAX308AESE+)
- Flat resistance across the signal range (对比 MAX308EU+)
设计说明
Treat the selected switch resistance as part of the analog signal-path transfer function. The MAX308EUE+ specifies on-resistance below 100 ohm and channel matching within 5 ohm, so use matched source and return routing where practical. Place the multiplexer close to the source or converter, keep both paths short, and avoid sharing a narrow return trace with unrelated switching currents. These layout practices reduce additional attenuation and channel-dependent measurement error.
Do not assume that identical package dimensions guarantee an interchangeable mux configuration. The MAX308 family supports 8:1 or dual 4:1 operation, while MAX309EUE+ is oriented toward dual 4:1 routing. Before substituting either candidate, compare the manufacturer pin-description table, common terminals, enable logic, select truth table, and operating-grade markings. A footprint match alone does not validate the functional connection of every signal terminal.
Route all eight analog inputs with consistent geometry and keep control traces away from sensitive sensor and return paths. Place any input filtering or protection close to the connector, with the multiplexer positioned where the selected signal can reach the downstream converter over a short, low-impedance path. Use a continuous ground reference beneath the analog area and avoid switching high-current return paths beneath the TSSOP to minimize coupling into the measurement channel.
Check the 5 V to 30 V supply range against the complete operating envelope and place bypass capacitance near the supply pins according to the manufacturer application guidance. Because the device is a CMOS analog switch rather than a power converter, its supply current and power dissipation are generally modest, but input and output signals must still remain inside the specified analog range. Confirm absolute maximum and operating limits before connecting external sources.
合规信息
The '+' ordering suffix appears in the MPN, but no explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 declaration was present in the cited product-page text. Obtain current declarations from Analog Devices before making a compliance claim.