Analog Devices

MAX333CPP+ - Quad SPDT CMOS Analog Switch | Maxim Integrated

Teilenummer: MAX333CPP+ ✓ Aktiv
+10 V to +30 V Vdss 250 ohm Rds(on) 20-pin PDIP Package
MOQ: 1 |

MAX333CPP+ Übersicht

The Maxim Integrated MAX333CPP+ is a quad, independent SPDT CMOS analog switch with four 2:1 channels, 250 ohm on-resistance, and a 20-pin PDIP package. It supports bipolar supplies from ±5 V to ±18 V or single-ended supplies from +10 V to +30 V, while its TTL- and CMOS-compatible control inputs operate from +0.8 V to +2.4 V. Break-before-make switching is 200 ns typical.

A CMOS analog switch is a voltage-controlled semiconductor device that routes analog signals between circuit nodes under digital control. An SPDT switch provides one common connection and two switched terminals, allowing a signal to select between two paths. The MAX333 belongs to the analog-switch hierarchy within interface ICs, where low on-resistance, controlled switching behavior, and broad supply-voltage support are important for signal routing and test systems.

The MAX333CPP+ combines four independent SPDT switches in one package. Its 250 ohm on-resistance supports general-purpose analog routing, while break-before-make operation prevents the two switched paths from being connected simultaneously during transition. The control inputs accept both TTL and CMOS logic levels across a +0.8 V to +2.4 V input range. Logic inputs and switched analog signals may operate anywhere between the supply rails without damage, according to the manufacturer datasheet.

The device can operate from dual bipolar supplies or a single-ended supply. Its switching architecture is intended to provide low-cost replacement of a DG211 and DG212 pair when four SPDT channels are required. The 200 ns typical break-before-make timing is relevant when the switched network must avoid momentarily connecting two sources together. Analog signal amplitude, supply polarity, control timing, and channel isolation remain important system-level constraints.

Typical uses include analog measurement systems, signal multiplexing, instrumentation, communications equipment, and industrial control modules where several independently controlled analog paths are needed. Each switch can route a sensor, reference, or test signal without requiring a separate discrete switch package for every channel. The quad integration reduces board area and simplifies control logic, although all four channels still require careful consideration of signal loading and supply bypassing.

For layout, place the device close to the signals being routed and keep analog traces away from high-speed digital switching nodes. Keep power-ground and signal-ground returns compact, and follow the pin-description table in the manufacturer datasheet when assigning PCB tracks. Designers should verify the maximum analog and logic voltages, supply configuration, and off-state behavior against the exact operating conditions before production release.

This page combines the manufacturer switching characteristics with package, application, replacement, and PCB-oriented guidance. It also identifies pin-compatible family options and clarifies the electrical constraints that matter when evaluating the MAX333CPP+ as a quad SPDT routing element.

Drop-in-Alternativen für MAX333CPP+ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

MAX333CPA

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 20-pin PDIP
RON 250 ohm with a 0 ohm difference; commercial temperature suffix differs from MAX333CPP+

📋 Referenzalternative (nicht im Katalog)

MAX333CPE

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 20-pin PDIP
RON 250 ohm with a 0 ohm difference; extended temperature suffix differs from MAX333CPP+

📋 Referenzalternative (nicht im Katalog)

MAX333CPP

✅ Drop-In
📦 20-pin PDIP
RON 250 ohm with a 0 ohm difference; non-plus ordering suffix differs from MAX333CPP+

📋 Referenzalternative (nicht im Katalog)

MAX333EPP

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 20-pin PDIP
RON 250 ohm with a 0 ohm difference; extended temperature ordering suffix differs from MAX333CPP+

📋 Referenzalternative (nicht im Katalog)

MAX333EPE

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 20-pin PDIP
RON 250 ohm with a 0 ohm difference; extended temperature and ordering suffix differs from MAX333CPP+

📋 Referenzalternative (nicht im Katalog)

MAX333CPP+ Grenzwerte & elektrische Eigenschaften

Number of Switches 4 circuits
Switch Configuration 2:1 SPDT per circuit
On-Resistance 250 ohm
Gehäuse 20-pin PDIP
Positive Supply Range +10 V to +30 V
Negative Supply Range -5 V to -18 V
Logic Input Compatibility TTL and CMOS
Guaranteed Logic Input Range +0.8 V to +2.4 V
Break-Before-Make Time 200 ns typical
Control Inputs 4 independent logic inputs
Analog Signal Range Anywhere between the supply voltages
Montageart Through-hole

MAX333CPP+ Pin-Konfiguration

DIP-20 Package Pinout Diagram DIP-20 20-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 DIP-20
Pin 1 COM1 — Common terminal for switch 1
Pin 2 NO1 — Normally open terminal for switch 1
Pin 3 NC1 — Normally closed terminal for switch 1
Pin 4 COM2 — Common terminal for switch 2
Pin 5 NO2 — Normally open terminal for switch 2
Pin 6 NC2 — Normally closed terminal for switch 2
Pin 7 V+ — Positive supply connection
Pin 8 GND — Ground connection
Pin 9 COM3 — Common terminal for switch 3
Pin 10 NO3 — Normally open terminal for switch 3
Pin 11 NC3 — Normally closed terminal for switch 3
Pin 12 COM4 — Common terminal for switch 4
Pin 13 NO4 — Normally open terminal for switch 4
Pin 14 NC4 — Normally closed terminal for switch 4
Pin 15 V- — Negative supply connection
Pin 16 IN1 — Control input for switch 1
Pin 17 IN2 — Control input for switch 2
Pin 18 IN3 — Control input for switch 3
Pin 19 IN4 — Control input for switch 4
Pin 20 GND — Ground connection

Typische Anwendungen

MAX333CPP+ ist geeignet für 6 Anwendungs: Analog Sensor Multiplexing, Instrumentation Signal Routing, Communications Signal Multiplexing, Industrial Control Signal Routing, Automated Test Equipment, Precision Analog Reference Selection.

🧩

Analog Sensor Multiplexing

The MAX333CPP+ fits sensor multiplexing because it combines four independent 2:1 switches with a 250 ohm on-resistance in one 20-pin PDIP package. Each channel can select between two sensor or conditioning paths under separate CMOS-compatible control signals. The guaranteed +0.8 V to +2.4 V logic-input range simplifies interfacing with common controller families. When multiplexed sensors have high source impedance, account for the 250 ohm path resistance to avoid excessive loading and settling errors. Break-before-make operation, rated at 200 ns typical, also helps prevent two selected sensor sources from being connected momentarily during switching.

🖥️

Instrumentation Signal Routing

The MAX333CPP+ is suitable for instrumentation systems that route test or measurement signals among multiple front-end paths. Four independent SPDT channels provide compact multiplexing without requiring four separate switch packages, while the 250 ohm on-resistance supports many general-purpose measurement interfaces. The logic inputs accept TTL and CMOS levels, allowing direct control from test-controller hardware. Layout should minimize trace length around the switched nodes because longer routes can increase capacitive pickup. Use a low-impedance return path and stable supply bypassing to preserve measurement repeatability during each 200 ns typical break-before-make transition.

🌐

Communications Signal Multiplexing

The MAX333CPP+ can route low-level analog paths in communications equipment where two sources must be selected for a common receiver or measurement chain. Its quad SPDT organization permits four independent selections, and its 250 ohm resistance should be considered against the source impedance and required attenuation. The device supports +10 V to +30 V single-ended operation or ±5 V to ±18 V bipolar operation, which accommodates several industrial signal-chain architectures. Keep routing traces short and away from clocks or fast data lines to reduce injected noise. The 200 ns typical break-before-make behavior prevents the old and new signal paths from overlapping during a transition.

🏭

Industrial Control Signal Routing

The MAX333CPP+ supports industrial control modules that must route command, feedback, or reference signals between two possible sources. Its independent control inputs allow software to manage all four switches, and the fully TTL- and CMOS-compatible +0.8 V to +2.4 V input range simplifies integration with industrial logic levels. The 250 ohm on-resistance is appropriate for many control and instrumentation paths rather than high-current power switching. Environmental requirements must be checked against the selected full ordering suffix. For factory equipment, place the device away from motor-switching nodes, use solid ground returns, and include local supply bypass capacitors close to the package pins.

🔧

Automated Test Equipment

The MAX333CPP+ can connect one common test node to either of two possible fixtures or sources in automated test equipment. Four independent channels reduce the number of discrete SPDT packages needed for a multi-point fixture, while the 250 ohm resistance should be included in the test-path error budget. TTL and CMOS-compatible control inputs simplify sequencing from test logic operating across the guaranteed +0.8 V to +2.4 V range. Keep fixture traces short and terminate unused channels according to the application. The break-before-make characteristic helps avoid connecting the active fixture to an incompatible source during switching.

📡

Precision Analog Reference Selection

The MAX333CPP+ can select between two analog references or conditioned signals when a system needs to change routing under digital control. Its 250 ohm on-resistance is simple to include in a precision error budget, provided the source impedance and downstream input are appropriate. Break-before-make operation prevents two references from being shorted together during transition, and the 200 ns typical timing provides a defined switching interval. The device does not improve source accuracy or buffer the selected signal, so reference noise, loading, and settling must be evaluated separately. Use careful grounding and short analog traces to preserve the selected reference during measurement.

Zusammenfassung der empfohlenen Produkte

MAX333CPP Same-family quad SPDT routing device Verwendet in: Analog Sensor Multiplexing, Automated Test Equipment, Precision Analog Reference Selection DG211 Discrete SPDT switch alternative cited by the manufacturer Verwendet in: Analog Sensor Multiplexing, Instrumentation Signal Routing, Automated Test Equipment DG212 Discrete SPDT switch alternative cited by the manufacturer Verwendet in: Analog Sensor Multiplexing, Communications Signal Multiplexing, Automated Test Equipment, Precision Analog Reference Selection MAX333CPA Same-family quad SPDT switch for commercial-temperature designs Verwendet in: Instrumentation Signal Routing, Precision Analog Reference Selection MAX333CPE Same-family quad SPDT switch with extended-temperature ordering Verwendet in: Instrumentation Signal Routing, Industrial Control Signal Routing MAX333EPP Same-family quad SPDT switch with extended ordering suffix Verwendet in: Communications Signal Multiplexing MAX333EPE Same-family extended-temperature quad SPDT option Verwendet in: Communications Signal Multiplexing, Industrial Control Signal Routing MAX333CPP+ Analog Devices Verwendet in: Industrial Control Signal Routing
What is the MAX333CPP+?
The MAX333CPP+ is a quad CMOS analog switch containing four independent SPDT, or 2:1, switches in a 20-pin PDIP package. According to the Maxim Integrated manufacturer datasheet, each circuit has a 250 ohm on-resistance, and the device supports single-ended supplies from +10 V to +30 V or bipolar supplies from ±5 V to ±18 V. It is intended for general-purpose analog signal routing, multiplexing, instrumentation, and control systems.
What is the on-resistance of the MAX333CPP+?
The MAX333CPP+ has a nominal 250 ohm on-resistance for each SPDT channel. This value is identified in the Analog Devices/Maxim Integrated product listing and manufacturer datasheet. On-resistance influences signal attenuation and input loading, particularly when the connected source has a relatively high impedance. The datasheet should be consulted for test conditions and voltage-dependent resistance characteristics before using the figure in a precision signal path.
Which supply voltages does the MAX333CPP+ accept?
The MAX333CPP+ accepts +10 V to +30 V in a single-ended configuration or ±5 V to ±18 V when both positive and negative supplies are used. The MAX333 family data sheet states that logic inputs and switched analog signals can range anywhere between the supply voltages without damage. Correct supply sequencing, decoupling, and absolute voltage limits should therefore be verified in the final circuit.
Are the MAX333CPP+ control inputs TTL and CMOS compatible?
Yes. The MAX333CPP+ control inputs are fully compatible with TTL and CMOS logic over a guaranteed +0.8 V to +2.4 V input range, according to the manufacturer datasheet. The input range is independent of the selected analog supply configuration. The two control inputs associated with each SPDT switch determine which of the two switched terminals is connected to the common terminal.
What does break-before-make mean for the MAX333CPP+?
Break-before-make means the MAX333CPP+ opens the existing connection before establishing the new one during a control transition. The family data sheet gives a typical break-before-make time of 200 ns. This behavior helps prevent the two switched nodes from being momentarily connected together, which is important when they carry incompatible sources, voltages, or external signals.
Where can I download the MAX333CPP+ datasheet PDF?
The official MAX333CPP+ datasheet PDF is available from Analog Devices at the MAX333 data-sheet link listed on this page. The document describes the quad SPDT architecture, 250 ohm on-resistance, TTL- and CMOS-compatible logic inputs, supported supply configurations, and the manufacturer's recommended operating conditions. Use the pin-description table in that document when creating or reviewing the PCB footprint.
Where can I find the MAX333CPP+ pinout?
The MAX333CPP+ pinout is shown in the official MAX333 manufacturer datasheet under the package and pin-description information. The device uses a 20-pin PDIP footprint with four common terminals, eight switched terminals, four control inputs, supply connections, and ground connections. Pin assignments should be transcribed directly from the datasheet rather than inferred from another package in the MAX333 family.
What is the MAX333CPP+ best used for?
The MAX333CPP+ is best suited to general-purpose analog routing that requires four independently controlled SPDT paths. Its 250 ohm on-resistance and 200 ns typical break-before-make timing support measurement, instrumentation, and control applications. Because it is a CMOS analog switch rather than a power switch, it is not intended for high-current loads or for carrying voltages beyond the permitted supply range.
What is the best drop-in replacement for MAX333CPP+?
The closest same-family drop-in choices include MAX333CPA, MAX333CPE, MAX333CPP, MAX333EPP, and MAX333EPE when their associated operating-temperature grades meet the design requirements. Each uses the same 20-pin PDIP quad-SPDT structure and shares the 250 ohm on-resistance. A replacement still requires verification of the temperature grade, control thresholds, supply limits, and exact suffix ordering code.
Can MAX333CPP replace MAX333CPP+?
The MAX333CPP and MAX333CPP+ use the same 20-pin PDIP quad-SPDT architecture and both are listed with 250 ohm on-resistance, so they can be board-compatible in principle. The exact ordering suffix must still be checked for operating-temperature grade, lead finish, and procurement requirements. According to the manufacturer ordering information, the correct decision is based on the full suffix rather than the base device name alone.
When should I choose MAX333CPP+ over another MAX333 suffix?
Choose MAX333CPP+ when a commercial-temperature, 20-pin PDIP quad-SPDT switch is required and its complete ordering code matches the system specification. Select MAX333CPA, MAX333CPE, MAX333EPP, or MAX333EPE only when their temperature grade is appropriate. All of these options retain the four-channel SPDT topology, while the suffix determines the qualification and environmental range.
Is MAX333CPP+ suitable for industrial analog measurement?
The MAX333CPP+ can suit industrial analog measurement systems when signal amplitude, bandwidth, isolation, and temperature requirements remain within the device limits. Its four independent SPDT channels allow multiplexing of sensors or test paths, and its 250 ohm on-resistance is appropriate for many general-purpose routing tasks. The industrial operating grade should be confirmed by selecting the appropriate MAX333 suffix for the required temperature range.
What is the difference between MAX333CPP+ and DG211 plus DG212?
The MAX333CPP+ integrates four independent SPDT switches in one 20-pin PDIP device, while a DG211 and DG212 pair normally requires two packages to provide the same total number of SPDT channels. The manufacturer describes the MAX333 as a low-cost replacement for a DG211/DG212 pair. Pin assignments, control polarity, supply levels, and signal limits must still be compared before treating the devices as interchangeable.
How do I design the PCB layout for MAX333CPP+?
Place the MAX333CPP+ close to the routed analog nodes and connect bypass capacitors to the supply and ground pins with short, low-inductance traces. Keep switching-control traces away from sensitive analog paths and use a quiet ground return to reduce coupling into the switched signals. The manufacturer datasheet provides the electrical pin descriptions; follow them exactly when routing the 20-pin PDIP footprint.
Where to buy MAX333CPP+ online and what is its lead time?
Use the Request a Quote form on this page to ask about MAX333CPP+ availability, current lead time, and order quantities. The form is the appropriate channel for a quote request and lets the buyer confirm the exact MAX333CPP+ ordering suffix. Stock status can change continuously, so current availability should be established directly through the quote request rather than inferred from a historical catalog listing.
How much does MAX333CPP+ cost and is it in stock?
Use the Request a Quote form on this page for the current price and stock status of MAX333CPP+. Pricing and inventory are time-sensitive and are not embedded as static customer-facing values in this technical description. The requested MPN is MAX333CPP+, including its complete package and ordering suffix, so the quote request should identify that exact part rather than the base MAX333 family.

Technische Referenzdaten für MAX333CPP+ – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose MAX333CPP+ when the design needs four independent SPDT analog switches in a 20-pin PDIP footprint and the commercial-temperature ordering suffix satisfies the environmental requirement. Its 250 ohm on-resistance is appropriate for general-purpose signal routing, not high-current or very low-resistance precision applications. MAX333CPP is the closest non-plus ordering option, while MAX333CPA, MAX333CPE, MAX333EPP, and MAX333EPE provide other temperature-grade choices within the same family. If a mixed-signal system already uses DG211 and DG212 switches, the MAX333 can reduce package count, but control polarity, pin functions, supply requirements, and absolute signal limits must be compared before replacement. For new designs requiring a smaller package or substantially lower on-resistance, choose a different device family and redesign the PCB rather than treating a functional equivalent as a drop-in replacement.

Vergleich mit Alternativen

Parameter Dieses Produkt MAX333CPA MAX333CPE MAX333CPP MAX333EPP MAX333EPE
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 20-pin PDIP 20-pin PDIP 20-pin PDIP 20-pin PDIP 20-pin PDIP 20-pin PDIP
Number of Switches 4 4 4 4 4 4
Switch Configuration SPDT, 2:1 SPDT, 2:1 SPDT, 2:1 SPDT, 2:1 SPDT, 2:1 SPDT, 2:1
On-Resistance 250 ohm 250 ohm 250 ohm 250 ohm 250 ohm 250 ohm
Positive Supply Range +10 V to +30 V +10 V to +30 V +10 V to +30 V +10 V to +30 V +10 V to +30 V +10 V to +30 V
Bipolar Supply Range ±5 V to ±18 V ±5 V to ±18 V ±5 V to ±18 V ±5 V to ±18 V ±5 V to ±18 V ±5 V to ±18 V
Guaranteed Logic Input Range +0.8 V to +2.4 V +0.8 V to +2.4 V +0.8 V to +2.4 V +0.8 V to +2.4 V +0.8 V to +2.4 V +0.8 V to +2.4 V
Break-Before-Make Time 200 ns typical 200 ns typical 200 ns typical 200 ns typical 200 ns typical 200 ns typical
Ordering-Suffix Qualification MAX333CPP+ commercial suffix MAX333CPA commercial suffix MAX333CPE extended suffix MAX333CPP non-plus suffix MAX333EPP extended suffix MAX333EPE extended suffix

Wichtigste Unterscheidungsmerkmale

  • Four independently controlled routing channels in one package (vs. DG211)
  • Consistent 250 ohm on-resistance across same-family alternatives (vs. MAX333CPP)
  • Guaranteed TTL and CMOS control-input compatibility (vs. MAX333EPP)
  • Integrated four-channel SPDT function (vs. DG211 and DG212)

Designhinweise

Route the four switched analog channels as short, direct traces because capacitance and pickup increase with loop area. Place the MAX333CPP+ near the source and destination nodes rather than near a distant connector, and avoid crossing the analog paths with clock, relay-driver, or high-current power traces. Keep bypass-capacitor connections to V+, V-, and ground short and use a continuous ground plane to reduce return-path discontinuities.

Do not treat the SPDT switches as power switches or allow switched signals to exceed the supply rails. The manufacturer states that logic inputs and analog signals can range anywhere between the supply voltages without damage, but normal operating signals should remain inside the permitted analog-signal range. Also confirm the complete ordering suffix before substitution because the MAX333CPP, MAX333CPA, MAX333CPE, MAX333EPP, and MAX333EPE variants differ in temperature-grade designators.

Include the 250 ohm on-resistance in the source-loading and gain-error calculation. If either connected source has appreciable impedance, the switch resistance can alter attenuation and input biasing. Keep switched nodes away from high-impedance leakage-sensitive inputs, and use the break-before-make interval, rated at 200 ns typical, to account for the transient period during which the previous path is being opened before the new path closes.

Separate the four control inputs from sensitive analog nodes where possible, even though the inputs are TTL- and CMOS-compatible over +0.8 V to +2.4 V. A logic transition can cause charge injection or coupling into a high-impedance switched node. Provide a low-impedance ground reference, avoid sharing long return paths with switching elements, and place any input filtering or protection close to the connector rather than at the device.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The available manufacturer and distributor pages do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for this ordering code. AEC-Q100 qualification is not applicable to this general-purpose commercial interface IC.

Daten verifiziert am: 2026-11-18 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

MAX333CPP+ datasheet MAX333CPP+ pinout MAX333CPP+ datasheet pdf MAX333CPP+ specifications Maxim Integrated MAX333CPP+ MAX333CPP+ 250 ohm SPDT MAX333CPP+ 20 pin PDIP MAX333CPP+ equivalent MAX333CPP+ replacement MAX333CPP+ cross reference MAX333CPP+ vs MAX333CPP MAX333CPP+ price MAX333CPP+ stock MAX333CPP+ application circuit MAX333CPP+ footprint

Verwandte Bauteile & Begriffe

Analog Devices Maxim Integrated MAX333CPP+ MAX333CPP MAX333CPA MAX333CPE MAX333EPP MAX333EPE DG211 DG212 CMOS analog switch SPT SPDT switch 2:1 analog switch interface IC semiconductor TTL-compatible logic input CMOS-compatible logic input on-resistance break-before-make switching 250 ohm 200 ns 20-pin PDIP through-hole package analog signal multiplexing signal routing
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen