MAX333CPP+ - Quad SPDT CMOS Analog Switch | Maxim Integrated
MPN: MAX333CPP+ ✓ فعالMAX333CPP+ جائزہ
A CMOS analog switch is a voltage-controlled semiconductor device that routes analog signals between circuit nodes under digital control. An SPDT switch provides one common connection and two switched terminals, allowing a signal to select between two paths. The MAX333 belongs to the analog-switch hierarchy within interface ICs, where low on-resistance, controlled switching behavior, and broad supply-voltage support are important for signal routing and test systems.
The MAX333CPP+ combines four independent SPDT switches in one package. Its 250 ohm on-resistance supports general-purpose analog routing, while break-before-make operation prevents the two switched paths from being connected simultaneously during transition. The control inputs accept both TTL and CMOS logic levels across a +0.8 V to +2.4 V input range. Logic inputs and switched analog signals may operate anywhere between the supply rails without damage, according to the manufacturer datasheet.
The device can operate from dual bipolar supplies or a single-ended supply. Its switching architecture is intended to provide low-cost replacement of a DG211 and DG212 pair when four SPDT channels are required. The 200 ns typical break-before-make timing is relevant when the switched network must avoid momentarily connecting two sources together. Analog signal amplitude, supply polarity, control timing, and channel isolation remain important system-level constraints.
Typical uses include analog measurement systems, signal multiplexing, instrumentation, communications equipment, and industrial control modules where several independently controlled analog paths are needed. Each switch can route a sensor, reference, or test signal without requiring a separate discrete switch package for every channel. The quad integration reduces board area and simplifies control logic, although all four channels still require careful consideration of signal loading and supply bypassing.
For layout, place the device close to the signals being routed and keep analog traces away from high-speed digital switching nodes. Keep power-ground and signal-ground returns compact, and follow the pin-description table in the manufacturer datasheet when assigning PCB tracks. Designers should verify the maximum analog and logic voltages, supply configuration, and off-state behavior against the exact operating conditions before production release.
This page combines the manufacturer switching characteristics with package, application, replacement, and PCB-oriented guidance. It also identifies pin-compatible family options and clarifies the electrical constraints that matter when evaluating the MAX333CPP+ as a quad SPDT routing element.
کے لیے ڈراپ اِن متبادل MAX333CPP+ — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
MAX333CPA
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX333CPE
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX333CPP
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX333EPP
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX333EPE
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX333CPP+ زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Number of Switches | 4 circuits |
| Switch Configuration | 2:1 SPDT per circuit |
| On-Resistance | 250 ohm |
| پیکیج | 20-pin PDIP |
| Positive Supply Range | +10 V to +30 V |
| Negative Supply Range | -5 V to -18 V |
| Logic Input Compatibility | TTL and CMOS |
| Guaranteed Logic Input Range | +0.8 V to +2.4 V |
| Break-Before-Make Time | 200 ns typical |
| Control Inputs | 4 independent logic inputs |
| Analog Signal Range | Anywhere between the supply voltages |
| ماؤنٹنگ ٹائپ | Through-hole |
MAX333CPP+ پن کنفیگریشن
| پن 1 | COM1 — Common terminal for switch 1 |
| پن 2 | NO1 — Normally open terminal for switch 1 |
| پن 3 | NC1 — Normally closed terminal for switch 1 |
| پن 4 | COM2 — Common terminal for switch 2 |
| پن 5 | NO2 — Normally open terminal for switch 2 |
| پن 6 | NC2 — Normally closed terminal for switch 2 |
| پن 7 | V+ — Positive supply connection |
| پن 8 | GND — Ground connection |
| پن 9 | COM3 — Common terminal for switch 3 |
| پن 10 | NO3 — Normally open terminal for switch 3 |
| پن 11 | NC3 — Normally closed terminal for switch 3 |
| پن 12 | COM4 — Common terminal for switch 4 |
| پن 13 | NO4 — Normally open terminal for switch 4 |
| پن 14 | NC4 — Normally closed terminal for switch 4 |
| پن 15 | V- — Negative supply connection |
| پن 16 | IN1 — Control input for switch 1 |
| پن 17 | IN2 — Control input for switch 2 |
| پن 18 | IN3 — Control input for switch 3 |
| پن 19 | IN4 — Control input for switch 4 |
| پن 20 | GND — Ground connection |
عام استعمالات
MAX333CPP+ کے لیے موزوں ہے 6 ایپلیکیشنs: Analog Sensor Multiplexing, Instrumentation Signal Routing, Communications Signal Multiplexing, Industrial Control Signal Routing, Automated Test Equipment, Precision Analog Reference Selection.
Analog Sensor Multiplexing
The MAX333CPP+ fits sensor multiplexing because it combines four independent 2:1 switches with a 250 ohm on-resistance in one 20-pin PDIP package. Each channel can select between two sensor or conditioning paths under separate CMOS-compatible control signals. The guaranteed +0.8 V to +2.4 V logic-input range simplifies interfacing with common controller families. When multiplexed sensors have high source impedance, account for the 250 ohm path resistance to avoid excessive loading and settling errors. Break-before-make operation, rated at 200 ns typical, also helps prevent two selected sensor sources from being connected momentarily during switching.
تجویز کردہ
Instrumentation Signal Routing
The MAX333CPP+ is suitable for instrumentation systems that route test or measurement signals among multiple front-end paths. Four independent SPDT channels provide compact multiplexing without requiring four separate switch packages, while the 250 ohm on-resistance supports many general-purpose measurement interfaces. The logic inputs accept TTL and CMOS levels, allowing direct control from test-controller hardware. Layout should minimize trace length around the switched nodes because longer routes can increase capacitive pickup. Use a low-impedance return path and stable supply bypassing to preserve measurement repeatability during each 200 ns typical break-before-make transition.
تجویز کردہ
Communications Signal Multiplexing
The MAX333CPP+ can route low-level analog paths in communications equipment where two sources must be selected for a common receiver or measurement chain. Its quad SPDT organization permits four independent selections, and its 250 ohm resistance should be considered against the source impedance and required attenuation. The device supports +10 V to +30 V single-ended operation or ±5 V to ±18 V bipolar operation, which accommodates several industrial signal-chain architectures. Keep routing traces short and away from clocks or fast data lines to reduce injected noise. The 200 ns typical break-before-make behavior prevents the old and new signal paths from overlapping during a transition.
تجویز کردہ
Industrial Control Signal Routing
The MAX333CPP+ supports industrial control modules that must route command, feedback, or reference signals between two possible sources. Its independent control inputs allow software to manage all four switches, and the fully TTL- and CMOS-compatible +0.8 V to +2.4 V input range simplifies integration with industrial logic levels. The 250 ohm on-resistance is appropriate for many control and instrumentation paths rather than high-current power switching. Environmental requirements must be checked against the selected full ordering suffix. For factory equipment, place the device away from motor-switching nodes, use solid ground returns, and include local supply bypass capacitors close to the package pins.
تجویز کردہ
Automated Test Equipment
The MAX333CPP+ can connect one common test node to either of two possible fixtures or sources in automated test equipment. Four independent channels reduce the number of discrete SPDT packages needed for a multi-point fixture, while the 250 ohm resistance should be included in the test-path error budget. TTL and CMOS-compatible control inputs simplify sequencing from test logic operating across the guaranteed +0.8 V to +2.4 V range. Keep fixture traces short and terminate unused channels according to the application. The break-before-make characteristic helps avoid connecting the active fixture to an incompatible source during switching.
تجویز کردہ
Precision Analog Reference Selection
The MAX333CPP+ can select between two analog references or conditioned signals when a system needs to change routing under digital control. Its 250 ohm on-resistance is simple to include in a precision error budget, provided the source impedance and downstream input are appropriate. Break-before-make operation prevents two references from being shorted together during transition, and the 200 ns typical timing provides a defined switching interval. The device does not improve source accuracy or buffer the selected signal, so reference noise, loading, and settling must be evaluated separately. Use careful grounding and short analog traces to preserve the selected reference during measurement.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا MAX333CPP+ — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MAX333CPA | MAX333CPE | MAX333CPP | MAX333EPP | MAX333EPE |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP |
| Number of Switches | 4 | 4 | 4 | 4 | 4 | 4 |
| Switch Configuration | SPDT, 2:1 | SPDT, 2:1 | SPDT, 2:1 | SPDT, 2:1 | SPDT, 2:1 | SPDT, 2:1 |
| On-Resistance | 250 ohm | 250 ohm | 250 ohm | 250 ohm | 250 ohm | 250 ohm |
| Positive Supply Range | +10 V to +30 V | +10 V to +30 V | +10 V to +30 V | +10 V to +30 V | +10 V to +30 V | +10 V to +30 V |
| Bipolar Supply Range | ±5 V to ±18 V | ±5 V to ±18 V | ±5 V to ±18 V | ±5 V to ±18 V | ±5 V to ±18 V | ±5 V to ±18 V |
| Guaranteed Logic Input Range | +0.8 V to +2.4 V | +0.8 V to +2.4 V | +0.8 V to +2.4 V | +0.8 V to +2.4 V | +0.8 V to +2.4 V | +0.8 V to +2.4 V |
| Break-Before-Make Time | 200 ns typical | 200 ns typical | 200 ns typical | 200 ns typical | 200 ns typical | 200 ns typical |
| Ordering-Suffix Qualification | MAX333CPP+ commercial suffix | MAX333CPA commercial suffix | MAX333CPE extended suffix | MAX333CPP non-plus suffix | MAX333EPP extended suffix | MAX333EPE extended suffix |
اہم امتیازی خصوصیات
- Four independently controlled routing channels in one package (بمقابلہDG211)
- Consistent 250 ohm on-resistance across same-family alternatives (بمقابلہMAX333CPP)
- Guaranteed TTL and CMOS control-input compatibility (بمقابلہMAX333EPP)
- Integrated four-channel SPDT function (بمقابلہDG211 and DG212)
ڈیزائن نوٹس
Route the four switched analog channels as short, direct traces because capacitance and pickup increase with loop area. Place the MAX333CPP+ near the source and destination nodes rather than near a distant connector, and avoid crossing the analog paths with clock, relay-driver, or high-current power traces. Keep bypass-capacitor connections to V+, V-, and ground short and use a continuous ground plane to reduce return-path discontinuities.
Do not treat the SPDT switches as power switches or allow switched signals to exceed the supply rails. The manufacturer states that logic inputs and analog signals can range anywhere between the supply voltages without damage, but normal operating signals should remain inside the permitted analog-signal range. Also confirm the complete ordering suffix before substitution because the MAX333CPP, MAX333CPA, MAX333CPE, MAX333EPP, and MAX333EPE variants differ in temperature-grade designators.
Include the 250 ohm on-resistance in the source-loading and gain-error calculation. If either connected source has appreciable impedance, the switch resistance can alter attenuation and input biasing. Keep switched nodes away from high-impedance leakage-sensitive inputs, and use the break-before-make interval, rated at 200 ns typical, to account for the transient period during which the previous path is being opened before the new path closes.
Separate the four control inputs from sensitive analog nodes where possible, even though the inputs are TTL- and CMOS-compatible over +0.8 V to +2.4 V. A logic transition can cause charge injection or coupling into a high-impedance switched node. Provide a low-impedance ground reference, avoid sharing long return paths with switching elements, and place any input filtering or protection close to the connector rather than at the device.
تعمیل کی معلومات
The available manufacturer and distributor pages do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for this ordering code. AEC-Q100 qualification is not applicable to this general-purpose commercial interface IC.