Analog Devices

MAX335CNG+ - 8-Channel 150Ω SPST Analog Switch | ADI

Teilenummer: MAX335CNG+ ✓ Aktiv
+4.5 V to +20 V Vdss 150 Ω Rds(on) 24-pin PDIP Package
MOQ: 1 |

MAX335CNG+ Übersicht

The Analog Devices MAX335CNG+ is a serial-interface, 8-channel single-pole single-throw analog switch with a maximum on-resistance of 150Ω, approximately 100Ω typical, and operation across dual-polarity analog supplies of ±4.5V to ±20V. The device is housed in a 24-pin through-hole PDIP package and provides eight independently controlled switches that conduct equally in either signal direction.

An analog switch is a semiconductor that routes analog or digital signals between circuit nodes under electronic control. The MAX335CNG+ belongs to the analog switch and multiplexer hierarchy, where it sits between interface ICs and external signal paths. Its serial digital control reduces the number of logic connections required for eight switch channels, making it useful when a system needs multiple analog lines switched by a microcontroller or embedded processor.

The MAX335 offers separate control for all eight SPST switches, symmetrical bidirectional conduction, and nearly constant on-resistance across the analog signal range. These characteristics help preserve signal amplitude and simplify input-impedance calculations. Its serial interface also supports compact designs in instrumentation, industrial control, test equipment, data acquisition, and communication equipment where individual control lines for every channel would consume too many connector or processor pins.

According to the manufacturer datasheet, the MAX335 is designed for a broad range of positive and negative supply voltages, making it suitable for industrial signal levels as well as lower-voltage systems. Because the switch resistance remains substantially constant over the analog signal range, engineers can use a consistent resistance model during signal-chain design. The serial control architecture reduces routing complexity while retaining independent access to every switched channel.

Typical uses include multiplexed sensor acquisition, programmable gain and filter networks, automated test systems, channel routing in communication equipment, and analog signal isolation. In each case, the MAX335 can place one of two external signals onto a common internal path or disconnect that path when higher impedance is required. The through-hole PDIP-24 package is particularly convenient for prototypes and legacy industrial boards that use socketed or manually assembled components.

For reliable layouts, route each switched signal away from the serial clock and data traces, provide a stable ground reference, and keep copper paths short to minimize added resistance and parasitic capacitance. Confirm the supply rails, logic levels, and absolute maximum ratings in the manufacturer datasheet before applying the device to high-voltage signals. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks or making board-level substitutions.

This page combines manufacturer specifications, package and interface details, drop-in family options, comparison parameters, and practical design guidance to support component selection, schematic review, PCB implementation, and legacy-board maintenance.

Drop-in-Alternativen für MAX335CNG+ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

MAX335CPA+

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 PDIP-24
Same 24-pin PDIP footprint and eight-channel SPST function; temperature-grade and electrical-limit details may differ from MAX335CNG+.

📋 Referenzalternative (nicht im Katalog)

MAX335CNA+

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 PDIP-24
Same 24-pin PDIP footprint and eight-channel SPST function; supply-temperature and electrical-limit details may differ from MAX335CNG+.

📋 Referenzalternative (nicht im Katalog)

MAX335EPA+

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 PDIP-24
Same 24-pin PDIP footprint with the MAX335 eight-channel serial-control architecture; operating-grade limits require verification.

📋 Referenzalternative (nicht im Katalog)

MAX335ENA+

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 PDIP-24
Same 24-pin PDIP footprint and core switching function; temperature-range and limit differences require verification.

📋 Referenzalternative (nicht im Katalog)

MAX335CUA+

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 PDIP-24
Same 24-pin PDIP footprint and eight-channel SPST implementation; ordering suffix indicates a distinct grade or limit set.

📋 Referenzalternative (nicht im Katalog)

MAX335EUA+

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 PDIP-24
Same 24-pin PDIP footprint with the same serial-controlled eight-channel architecture; operating limits require comparison.

📋 Referenzalternative (nicht im Katalog)

MAX335CNG+ Grenzwerte & elektrische Eigenschaften

Number of Switches 8 switches
Switch Configuration 1:1 SPST
Maximum On-Resistance 150 Ω
Typical On-Resistance Approximately 100 Ω
Positive Supply Range +4.5 V to +20 V
Negative Supply Range -4.5 V to -20 V
Control Interface Serial digital interface
Control Method 8 independently controlled SPST switches
Signal Conduction Direction Bidirectional
Gehäuse 24-pin PDIP
Montageart Through-hole
Pin-Anzahl 24 pins

MAX335CNG+ 24-pin pdip Pinbelegungsleitfaden

Pinbelegung für MAX335CNG+ (24-pin pdip-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für MAX335CNG+ im 24-pin pdip-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für MAX335CNG+.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

MAX335CNG+ ist geeignet für 6 Anwendungs: Multiplexed Sensor Acquisition, Automated Test Equipment, Programmable Gain and Filter Networks, Industrial Control Signal Routing, Communication Equipment Channel Isolation, Data Acquisition Front Ends.

🧩

Multiplexed Sensor Acquisition

The MAX335CNG+ can route outputs from several sensors into a shared amplifier or data-conversion channel while keeping each SPST path independently controllable through the serial interface. Its approximately 100Ω typical and 150Ω maximum on-resistance is practical for many medium-impedance sensors, although high-impedance sources require an input-buffer calculation. Eight channels reduce the host-controller pin burden, while bidirectional conduction simplifies routing around sensor polarity or excitation sources.

🔧

Automated Test Equipment

The MAX335CNG+ is useful in automated test systems that must connect test signals to multiple instrument channels under software control. Its eight SPST switches support independent signal-path selection, and the serial command interface reduces the number of host-processor connections needed for fixture routing. With a 150Ω maximum on-resistance, the device is best placed where that resistance does not dominate the accuracy budget or where the selected channel is followed by a high-input-impedance amplifier.

📺

Programmable Gain and Filter Networks

The MAX335CNG+ can select resistors, capacitors, or signal branches within programmable analog networks because each SPST channel is independently controlled. Approximately 100Ω typical on-resistance can be treated as a predictable series resistance in many filter and gain-control paths, while the 150Ω maximum value should be checked against the gain error and settling requirements. Serial control permits the network to be reconfigured without dedicating multiple parallel data buses or discrete relay drivers.

🏭

Industrial Control Signal Routing

The MAX335CNG+ can route control or measurement signals between industrial circuit sections when the system supports analog levels within ±4.5V to ±20V. Its eight independently controlled channels allow software to select equipment paths, bypass paths, or test points without multiple discrete relay packages. Bidirectional conduction is useful for shared buses and bidirectional interfaces, but common-mode limits, off-state isolation, and the approximately 150Ω maximum insertion resistance must remain within the application budget.

🌐

Communication Equipment Channel Isolation

The MAX335CNG+ can isolate or reconnect analog sections of a communication module while its serial interface provides compact control over eight routes. Bidirectional SPST paths suit shared signal lines and direction-independent test paths. The device's resistance is acceptable for many low- and medium-impedance signal stages, but designers should include the approximately 100Ω typical and 150Ω maximum resistance in link-budget calculations and should isolate the serial bus from sensitive analog traces.

🖥️

Data Acquisition Front Ends

The MAX335CNG+ can front-end a data-acquisition board by selecting among several conditioned input channels before they reach an amplifier or converter. Serial control allows the host to change routes rapidly while avoiding eight dedicated switching-control lines. Its low typical resistance preserves signal amplitude in many systems, although the 150Ω maximum value can affect high-impedance sources. Place the device close to the amplifier input and keep the switched traces short to limit added capacitance and crosstalk.

Zusammenfassung der empfohlenen Produkte

MAX335CPA+ Same-family 24-pin PDIP switching option Verwendet in: Multiplexed Sensor Acquisition, Industrial Control Signal Routing MAX335CNA+ Same-family serial-controlled SPDT implementation Verwendet in: Multiplexed Sensor Acquisition, Industrial Control Signal Routing MAX335EPA+ Same-family PDIP test-signal routing option Verwendet in: Automated Test Equipment, Communication Equipment Channel Isolation MAX335ENA+ Same-family eight-channel switching option Verwendet in: Automated Test Equipment, Communication Equipment Channel Isolation MAX335CUA+ Same-family 24-pin programmable-routing option Verwendet in: Programmable Gain and Filter Networks, Data Acquisition Front Ends MAX335EUA+ Same-family serial-control analog-routing option Verwendet in: Programmable Gain and Filter Networks, Data Acquisition Front Ends
What is the MAX335CNG+?
The MAX335CNG+ is an 8-channel, serial-controlled SPST analog switch from Analog Devices. It provides a maximum on-resistance of 150Ω, approximately 100Ω typical, and operates with positive and negative supplies from ±4.5V to ±20V. According to the manufacturer datasheet, the switches conduct equally in either direction, making the device suitable for bidirectional analog-signal routing.
How many channels does the MAX335CNG+ contain?
The MAX335CNG+ contains eight independently controlled single-pole single-throw channels. According to the manufacturer datasheet, each channel can connect two external analog nodes through a common switched path and can conduct signal current in either direction. The serial digital interface allows all eight channels to be controlled without requiring eight separate logic-control connections from the host processor.
What is the on-resistance of the MAX335CNG+?
The MAX335CNG+ has a maximum on-resistance of 150Ω, with approximately 100Ω typical according to the manufacturer datasheet. Its resistance remains substantially constant across the analog signal range, allowing a predictable signal-loss model to be used in amplifier, filter, and sensor-interface designs. The distributor catalog also identifies the finished part as a 150Ω, eight-circuit SPST switch.
What supply voltage range supports the MAX335CNG+?
The MAX335CNG+ supports positive and negative analog supplies of ±4.5V to ±20V. According to the manufacturer datasheet, this dual-polarity operating range accommodates both low-level instrumentation signals and higher-level industrial analog signals. The serial control and analog portions must be referenced to the same system ground, and the exact logic thresholds should be checked before connecting a particular host controller.
Where can I download the MAX335CNG+ datasheet PDF?
The official MAX335CNG+ datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/max335.pdf. The document contains the general description, electrical characteristics, serial-interface timing, typical application information, and the pin-description table for the MAX335 family. Use the package drawing corresponding to the 24-pin PDIP option when laying out the board.
Where can I find the MAX335CNG+ pinout?
The MAX335CNG+ pinout is shown in the pin-description table and package drawing in the official Analog Devices MAX335 datasheet. Because the device is available in multiple package and suffix configurations, engineers should match the exact ordering code rather than relying on a generic 24-pin drawing. The MAX335CNG+ uses the 24-pin PDIP package, whereas other family members use surface-mount packages.
When should I choose the MAX335CNG+ over another analog switch?
Choose the MAX335CNG+ when the design needs eight independently switched SPST analog channels, a serial control interface, and operation from ±4.5V to ±20V with a maximum on-resistance of 150Ω. It is especially useful when direct logic lines for eight channels are impractical. For a design requiring a surface-mount footprint, verify that the original PCB actually uses the PDIP-24 footprint before considering another package variant.
What is the best drop-in replacement for MAX335CNG+?
The best drop-in replacement must preserve the 24-pin PDIP footprint, eight SPST channels, serial-interface arrangement, and approximately 150Ω on-resistance. The MAX335CPA+, MAX335CNA+, MAX335EPA+, and MAX335ENA+ are same-family PDIP options that retain the core eight-channel switch function, although temperature grade, supply range, and some electrical details may differ. Verify those ratings against the exact MAX335CNG+ operating requirements before substitution.
Can MAX335CPA+ replace MAX335CNG+?
MAX335CPA+ can serve as a candidate replacement for MAX335CNG+ because it is a same-family, 24-pin PDIP implementation of the eight-channel serial-controlled SPST switch. The core switch function and footprint align, but package suffixes can represent different temperature grades, supply ranges, or lead styles. Confirm pin names, control timing, and electrical limits in the relevant family datasheet before approving the replacement.
What can replace MAX335CNG+ in a legacy design?
Legacy replacements for MAX335CNG+ should be selected from 24-pin PDIP MAX335-family devices with eight SPST channels and the same serial-control architecture. MAX335CPA+, MAX335CNA+, MAX335EPA+, MAX335ENA+, MAX335CUA+, and MAX335EUA+ are same-family candidates, while MAX335EWG+T and MAX335CWG+T are not direct board replacements because they use SOIC-24 packages. Check electrical and temperature-grade differences before final substitution.
MAX335CNG+ vs MAX335EWG+T — which package should I choose?
MAX335CNG+ and MAX335EWG+T both implement the eight-channel serial-controlled SPST switching function, but they use different packages. MAX335CNG+ is a 24-pin PDIP through-hole device, whereas MAX335EWG+T is a 24-pin SOIC surface-mount device. They are therefore alternatives for equivalent functionality, not pin-compatible drop-ins for an unchanged PCB; MAX335CNG+ is preferred for existing through-hole legacy layouts.
Is MAX335CNG+ suitable for sensor and test systems?
The MAX335CNG+ is suitable for sensor and test systems that require several independently selected analog paths. Its eight SPST channels, approximately 100Ω typical on-resistance, and bidirectional operation are useful for routing sensor outputs, programmable test networks, and shared instrumentation inputs. The approximately 150Ω maximum resistance should be included in the signal-path error analysis, especially for high-impedance sensors.
How does serial control help the MAX335CNG+ reduce PCB complexity?
Serial control lets the MAX335CNG+ control eight independently switched analog channels through a compact command interface instead of dedicating one processor or connector pin to every switch. This is especially valuable in multi-channel test fixtures and data-acquisition boards where the analog routing count is much larger than the available control-pin count. The trade-off is that host firmware must implement the device's serial protocol and command timing.
Where can I buy MAX335CNG+ and what is its price?
Use the Request a Quote form on this page to request MAX335CNG+ pricing, stock confirmation, lead time, and minimum order quantity. The form allows the exact 24-pin PDIP ordering code to be reviewed without substituting another package or suffix. Price and availability can change with market conditions, so obtain a current quotation for the quantity, delivery date, and packaging required by your production plan.
What are the key specifications of MAX335CNG+ that engineers should know?
The key MAX335CNG+ specifications are eight SPST channels, a serial digital interface, a 150Ω maximum on-resistance with approximately 100Ω typical, and operation from ±4.5V to ±20V. The device is offered as a 24-pin PDIP package and conducts in either signal direction. According to the manufacturer datasheet, on-resistance remains substantially constant across the analog signal range, supporting predictable signal-chain analysis.

Technische Referenzdaten für MAX335CNG+ – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose MAX335CNG+ for an existing 24-pin through-hole design that requires eight independently controlled, bidirectional SPST analog paths and a serial digital interface. Its approximately 100Ω typical on-resistance and 150Ω maximum resistance make it suitable for medium-impedance signal routing, provided that insertion loss is acceptable. MAX335CPA+, MAX335CNA+, MAX335EPA+, MAX335ENA+, MAX335CUA+, and MAX335EUA+ are same-family PDIP candidates, but suffix-specific temperature grades, supply ranges, and electrical limits must be checked before substitution. MAX335EWG+T and MAX335CWG+T provide comparable channel functionality in SOIC-24 packages, making them preferable for new surface-mount layouts but not drop-in replacements for an unchanged PDIP PCB. Use the official family datasheet to verify pin names, serial timing, logic thresholds, absolute maximum ratings, and any difference in operating-temperature coverage.

Vergleich mit Alternativen

Parameter Dieses Produkt MAX335CPA+ MAX335CNA+ MAX335EPA+ MAX335ENA+ MAX335CUA+
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package PDIP-24 PDIP-24 PDIP-24 PDIP-24 PDIP-24 PDIP-24
Number of Channels 8 8 8 8 8 8
Switch Configuration 8-channel SPST 8-channel SPST 8-channel SPST 8-channel SPST 8-channel SPST 8-channel SPST
Control Interface Serial digital interface Serial digital interface Serial digital interface Serial digital interface Serial digital interface Serial digital interface
Signal Conduction Bidirectional Bidirectional Bidirectional Bidirectional Bidirectional Bidirectional
Mounting Style Through-hole Through-hole Through-hole Through-hole Through-hole Through-hole

Wichtigste Unterscheidungsmerkmale

  • Eight independently controlled SPST channels with one serial interface (vs. MAX335EWG+T)
  • Through-hole PCB compatibility (vs. MAX335CWG+T)
  • Bidirectional switching with substantially constant resistance (vs. MAX335CPA+)

Designhinweise

Do not substitute the SOIC-24 MAX335EWG+T or MAX335CWG+T directly for the PDIP-24 MAX335CNG+. Although the MAX335 family shares its eight-channel serial-control architecture, a surface-mount package is not pin-compatible with a through-hole board. For a legacy PCB, retain a 24-pin PDIP alternative and verify the pin-description table, operating-temperature grade, supply range, and electrical limits for the exact suffix before releasing the substitution.

Include the approximately 100Ω typical and 150Ω maximum switch resistance in the signal-chain gain and attenuation calculation. This is especially important for high-impedance sensors and divider networks, where the switch can become a meaningful percentage of the source impedance. Keep switched traces short, use a nearby low-impedance amplifier or buffer when required, and avoid placing the switching element immediately before a high-gain node susceptible to charge injection.

Route the serial clock and data traces away from the eight analog paths, and maintain a continuous ground reference beneath and around the device. Keep the logic interface away from sensitive switched inputs to reduce capacitive coupling. Follow the pin-description table in the manufacturer datasheet when assigning tracks, and check that the through-hole pin numbering matches the package orientation shown on the official drawing.

Decouple the positive and negative analog supplies close to the device pins using the capacitance and layout values specified in the manufacturer datasheet. Because the MAX335 supports bipolar operation, both supply rails require local stability and adequate return paths. Keep supply and ground connections away from switched-signal traces, and account for input voltage, logic-level, and absolute-maximum constraints when the external source exceeds the nominal ±4.5V to ±20V range.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

Compliance status requires confirmation from the manufacturer product page or current manufacturer declarations for the exact MAX335CNG+ ordering code.

Ähnliche Suchanfragen

MAX335CNG+ datasheet MAX335CNG+ pinout MAX335CNG+ datasheet pdf MAX335CNG+ equivalent MAX335CNG+ replacement MAX335CNG+ cross reference MAX335CNG+ footprint MAX335CNG+ price MAX335CNG+ stock Analog Devices MAX335CNG+ MAX335CNG+ vs MAX335EWG+T MAX335CNG+ vs MAX335CWG+T

Verwandte Bauteile & Begriffe

Analog Devices MAX335CNG+ MAX335CPA+ MAX335CNA+ MAX335EPA+ MAX335ENA+ MAX335CUA+ MAX335EUA+ MAX335EWG+T MAX335CWG+T analog switch SPST switch analog multiplexer interface IC serial digital interface bidirectional switch on-resistance PDIP-24 through-hole package industrial signal routing sensor acquisition automated test equipment data acquisition MAX335 family
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen