MAX3485ECSA+T - 12Mbps 3.3V RS-485/RS-422 Transceiver | Analog Devices
Teilenummer: MAX3485ECSA+T ✓ AktivMAX3485ECSA+T Übersicht
An RS-485/RS-422 transceiver is a differential line-driver and line-receiver pair that lets two systems exchange data over a long, noisy cable. RS-422 is the balanced point-to-point standard, while RS-485 adds a multi-drop capability. Within the signal-chain hierarchy, a transceiver sits between a logic-level UART or microcontroller and a physical copper bus: UART logic levels enter the DI pin, the differential driver places Y and Z onto the cable, and the differential receiver returns a clean logic level on ROUT. A transceiver is therefore a physical-layer interface IC within the interface-IC category of semiconductor products.
Key features of the MAX3485ECSA+T include a 3 V to 3.6 V single supply operation, one driver and one receiver in a single package, 12 Mbps maximum signalling rate, ±15 kV ESD protection on bus pins, and a slew-rate-limited driver that reduces EMI and ringing on long cables. Short-circuit current limiting and thermal shutdown protect the driver output during overload or bus contention conditions.
Technically, the device combines a low-power differential driver with a fail-safe-tolerant receiver, so the receiver still resolves valid logic states when the bus is idle, partially terminated, or driven by another node. Because the driver edge rate is deliberately limited, the output spectrum is cleaner than a 12 Mbps-capable unlimited-rate driver, which makes the part easier to pass EMC pre-compliance testing in industrial cabinets. The single 3.3 V rail also allows direct interfacing with modern 3.3 V microcontrollers without level translation.
Typical uses include industrial instrumentation links, building-automation nodes, RS-485 to RS-485 repeater and concentrator designs, POS and metering equipment, and any point-to-point or multi-drop field bus running at 3.3 V logic levels.
When designing around this part, remember that the DE and /RE pins control direction, so pull both to a defined state at reset to avoid a floating bus. Also keep the Y and Z traces a matched, tightly coupled pair on a continuous ground plane to preserve differential impedance.
This page consolidates distributor availability data, verified drop-in alternatives, a parameter-by-parameter comparison, and practical layout notes that are not found in a single place in the manufacturer datasheet.
Drop-in-Alternativen für MAX3485ECSA+T – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MAX3485ECSA+T (gleiche Bauform und Footprint) – abweichend in Package, Product Type, Maximum Data Rate, Supported Standards, Driver Count.
MAX3485ESA+T
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →MAX3485CSA+
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →MAX3490ECSA-T
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX3485EESA+T
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →SN75HVD11DR
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX3485ECSA+T Technische Daten
| Product Type | RS-485/RS-422 half-duplex transceiver |
| Supply Voltage Range | 3 V to 3.6 V |
| Maximum Data Rate | 12 Mbps |
| ESD Protection (Bus Pins) | +/-15 kV |
| Driver / Receiver Count | 1 driver, 1 receiver |
| Duplex | Half-duplex |
| Driver Output Type | Slew-rate-limited differential |
| Gehäuse | 8-pin NSOIC (SOIC-8) |
| Montageart | Surface mount |
| Operating Supply Range | 3.3 V powered, single supply |
| RoHS-Status | RoHS3 compliant |
| Lead-Free Status | Lead free |
| Driver Protection | Short-circuit current limit and thermal shutdown |
| ESD Rating Reference | +/-15 kV ESD-protected bus pins |
| Data Rate of Alternative MAX3485CSA+ | 10 Mbps |
MAX3485ECSA+T Pin-Konfiguration
| Pin 1 | ROUT — Receiver output, logic-level data from the bus |
| Pin 2 | RE — Receiver enable, active low |
| Pin 3 | DE — Driver enable, active high |
| Pin 4 | DI — Driver input, logic-level data to the bus |
| Pin 5 | GND — Ground |
| Pin 6 | Y — Driver inverting output / bus node |
| Pin 7 | Z — Driver noninverting output / bus node |
| Pin 8 | VCC — Positive supply, 3.3 V nominal |
Typische Anwendungen
MAX3485ECSA+T ist geeignet für 6 Anwendungs: Industrial Sensor and Instrumentation Bus, Building Automation and HVAC Controllers, Point-to-Point RS-422 Link Between Boards, RS-485 to RS-485 Repeater and Concentrator, Metering, POS and Retail Terminal Equipment, Interface Bridge to Microcontroller UART.
Industrial Sensor and Instrumentation Bus
The MAX3485ECSA+T suits field-bus nodes that must pull data from remote sensors over long shielded cables. Its 12 Mbps maximum rate gives ample margin for 115.2 kbit/s or 1 Mbit/s instrument protocols, while the slew-rate-limited driver keeps the differential spectrum narrow and reduces ringing that would otherwise corrupt readings on unterminated runs. The +/-15 kV bus-pin ESD rating matters in cabinets where cables are frequently plugged and unplugged under maintenance. Operating from a single 3.3 V rail lets the transceiver sit directly beside a 3.3 V microcontroller, and the half-duplex DE//RE control lets one transceiver serve the whole node instead of separate transmit and receive parts.
Empfohlen
Building Automation and HVAC Controllers
Building-automation panels typically run RS-485 or RS-422 links between floor controllers, dampers and thermostats, and the MAX3485ECSA+T is a good fit for those nodes. Because the driver edge rate is deliberately limited, the device minimises common-mode energy and radiated emissions, which helps multi-controller cabinets pass EMC pre-compliance testing without heavy filtering. The 8-pin SOIC footprint is easy to place alongside an MCU on a mixed-signal control board, and the 3 V to 3.6 V supply range matches the single 3.3 V rails common in modern HVAC controllers. Half-duplex operation means one pair of twisted wires serves the whole controller chain, reducing wiring cost in building retrofits.
Empfohlen
Point-to-Point RS-422 Link Between Boards
When two assemblies must exchange data over a balanced line with no shared bus, RS-422 gives better noise immunity than RS-485, and the MAX3485ECSA+T implements both standards with the same pins. Running the two nodes at opposite ends of a cable inside a machine or rack benefits from the receiver's ability to resolve valid states on an idle bus, while the short-circuit and thermal-shutdown protection on the driver prevents latch-up if the far end is powered down or mis-terminated. The 12 Mbps ceiling lets the same design scale from a 9600 baud service port to a fast motion-control command path, so engineers can standardise on one transceiver SKU across several boards.
Empfohlen
RS-485 to RS-485 Repeater and Concentrator
Repeaters and concentrators sit between two bus segments and must regenerate the signal rather than merely buffer logic levels, so a true RS-485/RS-422 transceiver with a controlled driver edge is the correct building block. The MAX3485ECSA+T's slew-rate-limited output produces a clean differential waveform that regenerates well across the repeater boundary, and its 12 Mbps headroom allows each segment to run at full node rate. The DE and /RE pins let the repeater switch direction instantly at the end of a packet, and the single 3.3 V rail simplifies powering many repeater channels from one supply in a DIN-rail or rack-mount enclosure.
Empfohlen
Metering, POS and Retail Terminal Equipment
Electricity meters, fuel dispensers and point-of-sale terminals commonly expose an RS-485 or RS-422 service port for utility readers, and the MAX3485ECSA+T provides the physical layer for those links. The device's low 3.3 V operation lets it share the rail with the terminal's display and communications processor, while ±15 kV bus-pin ESD protection guards the port against the electrostatic exposure typical of shop-floor and outdoor metering cabinets. The 12 Mbps capability covers current high-speed meter protocols, and the compact SOIC-8 outline leaves board area for the connector and isolation components in a crowded terminal enclosure.
Empfohlen
Interface Bridge to Microcontroller UART
Many microcontrollers expose only a UART, so a level-converting transceiver is required to reach a differential RS-485 network. The MAX3485ECSA+T bridges that gap with a DI input and a ROUT output that sit at 3.3 V logic levels, so no translator IC is needed between the MCU pins and the transceiver. Firmware can toggle DE around each transmission to arbitrate bus direction, and the /RE pin can be tied low so the receiver is always active for diagnostics and collision detection. At 12 Mbps the link rate is limited by the UART and cable, not the transceiver, which gives ample margin for protocol overhead and framing.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MAX3485ECSA+T – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MAX3485ESA+T | MAX3485CSA+ | MAX3490ECSA-T | MAX3485EESA+T | SN75HVD11DR |
|---|---|---|---|---|---|---|
| Package | 8-SOIC (NSOIC) | 8-SOIC (NSOIC) - same | 8-SOIC (NSOIC) - same | 8-SOIC (NSOIC) - same | 8-SOIC (NSOIC) - same | 8-SOIC (NSOIC) - same |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Texas Instruments |
| Driver / Receiver Count | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver |
Wichtigste Unterscheidungsmerkmale
- Higher maximum data rate than the non-E MAX3485CSA+ in the same footprint (vs. MAX3485CSA+)
- No footprint change required against the closest Texas Instruments option (vs. SN75HVD11DR)
- Single fixed slew-limited driver profile simplifies EMC and signal-integrity work (vs. SN75HVD11DR)
- Direct same-family interchange with the temperature-grade ordering variants (vs. MAX3485EESA+T)
Designhinweise
Route Y and Z as a tightly coupled differential pair over a continuous ground plane, with the pair length matched within a few millimetres and no stubs to test points or unused pins. Keep the transceiver close to the connector so surge and ESD currents are diverted into the chassis or earth plane before they reach the logic section, and place the optional bus termination resistor directly at the driver end of the pair rather than at the transceiver.
The device runs from a single 3.3 V rail (3 V to 3.6 V), so place a 100 nF ceramic decoupling capacitor as close as possible to the VCC pin and add a bulk capacitor of roughly 1 uF to 10 uF at the supply entry point. Because the DE and /RE logic pins are driven by a microcontroller, tie them to defined states through the firmware or a pull resistor so the bus is never left floating during reset or brownout, which could otherwise produce an unintended differential pulse on the line.
The slew-rate-limited driver is the main reason this transceiver is easy to pass EMC testing, so keep that behaviour intact: do not parallel multiple transceivers onto the same bus pair to increase drive strength, and avoid adding external capacitive loads at the connector. If radiated emissions still exceed limits, first re-check that the cable shield is properly bonded and that common-mode chokes are sized for the actual data rate, rather than forcing the driver harder.
A frequent integration error is asserting DE and /RE at the same time in order to listen while transmitting, which can cause driver contention on multi-drop buses. Decide explicitly whether echo is required; otherwise hold /RE low only during receive windows and deassert DE before the last stop bit. Also verify that the transceiver ground is tied to the cable shield reference correctly, since a missing or reversed shield bond is a more frequent cause of noise problems than the transceiver itself.
Compliance-Informationen
Manufacturer product documentation and distributor listings state RoHS3 compliant and lead free for the MAX3485ECSA+T ordering code. No AEC-Q100 qualification is claimed for this industrial interface part.