Analog Devices

MAX3485ECSA+T - 12Mbps 3.3V RS-485/RS-422 Transceiver | Analog Devices

部品番号: MAX3485ECSA+T ✓ 生産中
3 V to 3.6 V Vdss 8-pin NSOIC (SOIC-8) Package
MOQ: 1 |

MAX3485ECSA+T 概要

The Analog Devices MAX3485ECSA+T is a 3.3 V-powered, slew-rate-limited true RS-485/RS-422 half-duplex transceiver rated for data rates up to 12 Mbps, with ±15 kV ESD protection on the bus pins, housed in an 8-pin SOIC (NSOIC-8) surface-mount package.

An RS-485/RS-422 transceiver is a differential line-driver and line-receiver pair that lets two systems exchange data over a long, noisy cable. RS-422 is the balanced point-to-point standard, while RS-485 adds a multi-drop capability. Within the signal-chain hierarchy, a transceiver sits between a logic-level UART or microcontroller and a physical copper bus: UART logic levels enter the DI pin, the differential driver places Y and Z onto the cable, and the differential receiver returns a clean logic level on ROUT. A transceiver is therefore a physical-layer interface IC within the interface-IC category of semiconductor products.

Key features of the MAX3485ECSA+T include a 3 V to 3.6 V single supply operation, one driver and one receiver in a single package, 12 Mbps maximum signalling rate, ±15 kV ESD protection on bus pins, and a slew-rate-limited driver that reduces EMI and ringing on long cables. Short-circuit current limiting and thermal shutdown protect the driver output during overload or bus contention conditions.

Technically, the device combines a low-power differential driver with a fail-safe-tolerant receiver, so the receiver still resolves valid logic states when the bus is idle, partially terminated, or driven by another node. Because the driver edge rate is deliberately limited, the output spectrum is cleaner than a 12 Mbps-capable unlimited-rate driver, which makes the part easier to pass EMC pre-compliance testing in industrial cabinets. The single 3.3 V rail also allows direct interfacing with modern 3.3 V microcontrollers without level translation.

Typical uses include industrial instrumentation links, building-automation nodes, RS-485 to RS-485 repeater and concentrator designs, POS and metering equipment, and any point-to-point or multi-drop field bus running at 3.3 V logic levels.

When designing around this part, remember that the DE and /RE pins control direction, so pull both to a defined state at reset to avoid a floating bus. Also keep the Y and Z traces a matched, tightly coupled pair on a continuous ground plane to preserve differential impedance.

This page consolidates distributor availability data, verified drop-in alternatives, a parameter-by-parameter comparison, and practical layout notes that are not found in a single place in the manufacturer datasheet.

ドロップイン代替品: MAX3485ECSA+T — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: MAX3485ECSA+T (同一形状・フットプリント) — 相違点: Package, Product Type, Maximum Data Rate, Supported Standards, Driver Count.

Maxim Integrated
Package: 8-SOIC, 0.154 inch, 3.90 mm width
Product Type: RS-485/RS-422 transceiver
Supported Standards: RS-485 and RS-422
比較対象 MAX3485ECSA+T →
Analog Devices
Package: 8-pin SOIC (NSOIC-8)
Maximum Data Rate: 10 Mbps
Supported Standards: RS-422 and RS-485
比較対象 MAX3485ECSA+T →
Analog Devices
Package: 8-pin SOIC
Product Type: 1/1 RS-422/RS-485 transceiver
Maximum Data Rate: 12Mbps
比較対象 MAX3485ECSA+T →
Analog Devices
Package: 8-SOIC
Product Type: RS-485/RS-422 transceiver
Maximum Data Rate: 10 Mbps
比較対象 MAX3485ECSA+T →

MAX3485ESA+T

✅ ドロップイン
Analog Devices
📦 8-SOIC (NSOIC)
RS-485/RS-422 transceiver · 3.3 V · 10 Mbps · 1 · 1 · Half-duplex · RS-422 and RS-485 · 8-SOIC

価格はお問い合わせください

データシートを見る →

MAX3485CSA+

✅ ドロップイン
Maxim Integrated
📦 8-SOIC (NSOIC)
RS-485/RS-422 transceiver · 3.3 V · 10 Mbps · Half-duplex · 1 driver · 1 receiver · RS-485 and RS-422 · Slew-rate-limited driver family feature

価格はお問い合わせください

データシートを見る →

MAX3490ECSA-T

✅ ドロップイン
📦 8-SOIC (NSOIC)
same SOIC-8 RS-485/RS-422 footprint and 3.3 V class operation, but with different fail-safe and bus-recovery behaviour plus a different maximum data rate than the 12 Mbps MAX3485ECSA+T

📋 参考代替品(カタログ未掲載)

MAX3485EESA+T

✅ ドロップイン
Analog Devices
📦 8-SOIC (NSOIC)
1/1 RS-422/RS-485 transceiver · 3V to 3.6V · 12Mbps · ±15kV · 1 driver · 1 receiver · RS-422 and RS-485 · Half-duplex

価格はお問い合わせください

データシートを見る →

SN75HVD11DR

✅ ドロップイン
📦 8-SOIC (NSOIC)
same 3.3 V half-duplex 8-SOIC transceiver footprint, but offers a 1/8 unit-load option for up to 256 nodes and selectable 1/10/32 Mbps driver transition times instead of one fixed 12 Mbps slew-limited profile

📋 参考代替品(カタログ未掲載)

MAX3485ECSA+T 仕様

Product Type RS-485/RS-422 half-duplex transceiver
Supply Voltage Range 3 V to 3.6 V
Maximum Data Rate 12 Mbps
ESD Protection (Bus Pins) +/-15 kV
Driver / Receiver Count 1 driver, 1 receiver
Duplex Half-duplex
Driver Output Type Slew-rate-limited differential
パッケージ 8-pin NSOIC (SOIC-8)
実装タイプ Surface mount
Operating Supply Range 3.3 V powered, single supply
RoHS ステータス RoHS3 compliant
Lead-Free Status Lead free
Driver Protection Short-circuit current limit and thermal shutdown
ESD Rating Reference +/-15 kV ESD-protected bus pins
Data Rate of Alternative MAX3485CSA+ 10 Mbps

MAX3485ECSA+T ピン構成

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
ピン 1 ROUT — Receiver output, logic-level data from the bus
ピン 2 RE — Receiver enable, active low
ピン 3 DE — Driver enable, active high
ピン 4 DI — Driver input, logic-level data to the bus
ピン 5 GND — Ground
ピン 6 Y — Driver inverting output / bus node
ピン 7 Z — Driver noninverting output / bus node
ピン 8 VCC — Positive supply, 3.3 V nominal

主な用途

MAX3485ECSA+T の用途: 6 件s: Industrial Sensor and Instrumentation Bus, Building Automation and HVAC Controllers, Point-to-Point RS-422 Link Between Boards, RS-485 to RS-485 Repeater and Concentrator, Metering, POS and Retail Terminal Equipment, Interface Bridge to Microcontroller UART.

🏭

Industrial Sensor and Instrumentation Bus

The MAX3485ECSA+T suits field-bus nodes that must pull data from remote sensors over long shielded cables. Its 12 Mbps maximum rate gives ample margin for 115.2 kbit/s or 1 Mbit/s instrument protocols, while the slew-rate-limited driver keeps the differential spectrum narrow and reduces ringing that would otherwise corrupt readings on unterminated runs. The +/-15 kV bus-pin ESD rating matters in cabinets where cables are frequently plugged and unplugged under maintenance. Operating from a single 3.3 V rail lets the transceiver sit directly beside a 3.3 V microcontroller, and the half-duplex DE//RE control lets one transceiver serve the whole node instead of separate transmit and receive parts.

🏠

Building Automation and HVAC Controllers

Building-automation panels typically run RS-485 or RS-422 links between floor controllers, dampers and thermostats, and the MAX3485ECSA+T is a good fit for those nodes. Because the driver edge rate is deliberately limited, the device minimises common-mode energy and radiated emissions, which helps multi-controller cabinets pass EMC pre-compliance testing without heavy filtering. The 8-pin SOIC footprint is easy to place alongside an MCU on a mixed-signal control board, and the 3 V to 3.6 V supply range matches the single 3.3 V rails common in modern HVAC controllers. Half-duplex operation means one pair of twisted wires serves the whole controller chain, reducing wiring cost in building retrofits.

🔧

Point-to-Point RS-422 Link Between Boards

When two assemblies must exchange data over a balanced line with no shared bus, RS-422 gives better noise immunity than RS-485, and the MAX3485ECSA+T implements both standards with the same pins. Running the two nodes at opposite ends of a cable inside a machine or rack benefits from the receiver's ability to resolve valid states on an idle bus, while the short-circuit and thermal-shutdown protection on the driver prevents latch-up if the far end is powered down or mis-terminated. The 12 Mbps ceiling lets the same design scale from a 9600 baud service port to a fast motion-control command path, so engineers can standardise on one transceiver SKU across several boards.

🌐

RS-485 to RS-485 Repeater and Concentrator

Repeaters and concentrators sit between two bus segments and must regenerate the signal rather than merely buffer logic levels, so a true RS-485/RS-422 transceiver with a controlled driver edge is the correct building block. The MAX3485ECSA+T's slew-rate-limited output produces a clean differential waveform that regenerates well across the repeater boundary, and its 12 Mbps headroom allows each segment to run at full node rate. The DE and /RE pins let the repeater switch direction instantly at the end of a packet, and the single 3.3 V rail simplifies powering many repeater channels from one supply in a DIN-rail or rack-mount enclosure.

💳

Metering, POS and Retail Terminal Equipment

Electricity meters, fuel dispensers and point-of-sale terminals commonly expose an RS-485 or RS-422 service port for utility readers, and the MAX3485ECSA+T provides the physical layer for those links. The device's low 3.3 V operation lets it share the rail with the terminal's display and communications processor, while ±15 kV bus-pin ESD protection guards the port against the electrostatic exposure typical of shop-floor and outdoor metering cabinets. The 12 Mbps capability covers current high-speed meter protocols, and the compact SOIC-8 outline leaves board area for the connector and isolation components in a crowded terminal enclosure.

🖥️

Interface Bridge to Microcontroller UART

Many microcontrollers expose only a UART, so a level-converting transceiver is required to reach a differential RS-485 network. The MAX3485ECSA+T bridges that gap with a DI input and a ROUT output that sit at 3.3 V logic levels, so no translator IC is needed between the MCU pins and the transceiver. Firmware can toggle DE around each transmission to arbitrate bus direction, and the /RE pin can be tied low so the receiver is always active for diagnostics and collision detection. At 12 Mbps the link rate is limited by the UART and cable, not the transceiver, which gives ample margin for protocol overhead and framing.

What is the MAX3485ECSA+T and what does it do?
The MAX3485ECSA+T is a 3.3 V-powered, half-duplex transceiver that combines one differential driver and one differential receiver for true RS-485 and RS-422 communication. According to the Analog Devices product page for the MAX3485E family, it is a 3.3 V powered, +/-15 kV ESD-protected, 12 Mbps, slew-rate-limited true RS-485/RS-422 transceiver. The driver converts the DI logic input into a balanced differential pair on Y and Z, while the receiver converts that differential pair back into a logic level on ROUT, so a single pair of conductors carries data in both directions with one driver active at a time.
What is the operating voltage range of the MAX3485ECSA+T?
The MAX3485ECSA+T operates from a single 3.3 V supply with a stated range of 3 V to 3.6 V. The manufacturer describes the MAX3485E family as a 3.3 V-powered part, and the part listing confirms the 3 V to 3.6 V supply condition. Because the device runs entirely from a 3.3 V rail, its DI, DE, /RE and ROUT logic levels are directly compatible with 3.3 V microcontrollers, UARTs and FPGAs without external level translators. No negative supply is required, which simplifies rail planning in low-voltage industrial and portable designs.
What is the maximum data rate of the MAX3485ECSA+T?
The MAX3485ECSA+T supports data rates up to 12 Mbps. Analog Devices specifies the MAX3485E family as a 12 Mbps, slew-rate-limited true RS-485/RS-422 transceiver, and distributor product listings repeat the 12 Mbps figure in the part title. The controlled driver transition rate keeps the differential output spectrum narrow enough to reduce ringing and radiated emissions on long cables, which is why the part remains usable at its full rated speed in industrial cable runs rather than only on short bench wiring.
How much ESD protection does the MAX3485ECSA+T provide?
The MAX3485ECSA+T provides +/-15 kV ESD protection on the bus pins. Both the Analog Devices product page and distributor listings describe the device as a 15 kV ESD-protected RS-485/RS-422 transceiver. This protection is specified at the Y and Z bus pins, where cables are plugged in and electrostatic discharge events actually occur, rather than only on logic pins. It makes the part suitable for exposed industrial and building-automation cabling without adding external TVS protection on every node.
What package does the MAX3485ECSA+T come in, and where is the pinout?
The MAX3485ECSA+T is supplied in an 8-pin NSOIC package, equivalent to an SOIC-8 surface-mount footprint, and the pinout is fully documented in the manufacturer datasheet. The 8-pin SOIC arrangement places ROUT on pin 1, /RE on pin 2, DE on pin 3, DI on pin 4, GND on pin 5, Y on pin 6, Z on pin 7 and VCC on pin 8. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks and keep the Y/Z pair adjacent for controlled differential impedance.
Where can I download the MAX3485ECSA+T datasheet PDF?
The MAX3485ECSA+T datasheet is available from the Analog Devices product page for the MAX3485E family at https://www.analog.com/en/products/max3485e.html, and mirrored PDF copies are hosted by parts-data providers such as alldatasheet.com and digchip.com. The manufacturer document describes the device as a 3.3 V-powered, +/-15 kV ESD-protected, 12 Mbps, slew-rate-limited true RS-485/RS-422 transceiver, and includes the pin description, electrical characteristics and typical application circuit. Download the manufacturer PDF for design sign-off, since third-party mirrors are re-hostings of the same document.
Is the MAX3485ECSA+T half-duplex or full-duplex, and how many drivers does it contain?
The MAX3485ECSA+T is a half-duplex transceiver containing one driver and one receiver. The manufacturer product description and distributor listings identify it as a one-driver, one-receiver half-duplex RS-485/RS-422 device in an 8-pin SOIC package. Direction is controlled by the DE (driver enable) and /RE (receiver enable, active low) pins, so a single pair of bus wires is shared for transmit and receive. Because the driver and receiver share the same Y and Z nodes, the two enables should never be asserted at the same time except in the deliberate echo-enabled case.
What is the difference between the MAX3485ECSA+T and the MAX3485CSA+?
The MAX3485ECSA+T is rated for 12 Mbps while the MAX3485CSA+ is rated for 10 Mbps, a 17 percent lower maximum data rate, and both are 3.3 V-powered true RS-485/RS-422 half-duplex transceivers in an 8-pin NSOIC package. The MAX3485CSA+ description states a transmission data rate up to 10 Mbps with short-circuit current limiting and thermal shutdown, and both families carry driver short-circuit protection. If your link runs at a fixed baud rate well below 10 Mbps, the MAX3485CSA+ is functionally sufficient; if you need the full 12 Mbps margin, stay with the MAX3485ECSA+T.
MAX3485ECSA+T vs SN75HVD11DR - which is better for a 3.3V RS-485 link?
Both devices are 3.3 V half-duplex RS-485 transceivers in 8-pin SOIC packages, but they target different bus topologies. The SN75HVD11 offers a 1/8 unit-load option supporting up to 256 nodes on the bus, selectable driver transition times for 1 Mbps, 10 Mbps and 32 Mbps signalling, and ESD protection exceeding 16 kV HBM. The MAX3485ECSA+T offers a single slew-rate-limited profile up to 12 Mbps with +/-15 kV ESD protection. Choose the MAX3485ECSA+T for clean fixed-rate industrial links and the SN75HVD11DR for dense multi-drop node counts and selectable edge rates.
When should I choose the MAX3485ECSA+T over the MAX3490ECSA-T?
Choose the MAX3485ECSA+T when you need a single 3.3 V supply with 12 Mbps operation and a slew-rate-limited driver for reduced EMI, and choose the MAX3490ECSA-T when your design requires that part's specific fail-safe and bus-recovery behaviour. Both sit in the same SOIC-8 footprint family for RS-485/RS-422 interfaces, so they are frequently compared in replacement guides. The MAX3485ECSA+T is the safer general-purpose choice for 3.3 V nodes that must interoperate with standard half-duplex field-bus equipment without special termination networks.
What is the best drop-in replacement for the MAX3485ECSA+T?
The best drop-in replacements for the MAX3485ECSA+T in the 8-pin SOIC footprint are the MAX3485CSA+ at 10 Mbps, the MAX3485ESA+T temperature-grade variant, and the Texas Instruments SN75HVD11DR for high-node-count buses. All share the same SOIC-8 pin arrangement with ROUT, /RE, DE, DI, GND, Y, Z and VCC, so the PCB does not change. Because driver edge rates and receiver thresholds differ between families, re-verify signalling margins and bus termination in the target system before releasing a substitute into production.
Is the MAX3485ECSA+T the same as the MAX3485ESA+T?
The MAX3485ECSA+T and the MAX3485ESA+T are the same 3.3 V, 12 Mbps, slew-rate-limited true RS-485/RS-422 transceiver die in the 8-pin NSOIC package, differing mainly in their temperature grade and ordering codes. The E suffix in the MAX3485E family denotes the extended-temperature option, while the +T suffix denotes tape-and-reel packaging. Drop-in interchange between them is electrically valid because the pinout and core ratings are identical, but verify the temperature range of the specific grade against your ambient requirements before substituting.
Where can I buy the MAX3485ECSA+T online and what does it cost?
The MAX3485ECSA+T is stocked by major authorized distributors and is also listed on the manufacturer product page for the MAX3485E family, which links to regional sales contacts. Pricing for this part changes with volume, currency and market conditions, so the current unit price and stock position are shown on this page and can be requested directly through the Request a Quote form on this page. For prototype quantities one piece, for production builds use the quantity-break table on this page, and for scheduled deliveries submit a Request a Quote with your target quantity and required delivery date.
What is the lead time and stock status for the MAX3485ECSA+T?
The MAX3485ECSA+T is listed as a production part on the Analog Devices product page for the MAX3485E family, and distributor listings for the 8-SOIC ordering code show the part as an active, orderable item. Current lead time, minimum order quantity and stock levels vary by region and order volume, so they should be confirmed for your project through the Request a Quote form on this page. For new designs, request a scheduled allocation early because RS-485 interface parts commonly move between lead-time bands as industry inventory cycles change.
What are the key specifications of the MAX3485ECSA+T that engineers should know?
The MAX3485ECSA+T is a 3.3 V-powered (3 V to 3.6 V) half-duplex RS-485/RS-422 transceiver with one driver and one receiver, rated for 12 Mbps data rate with +/-15 kV ESD protection on the bus pins. It uses a slew-rate-limited differential driver, includes driver short-circuit current limiting and thermal shutdown, and comes in an 8-pin NSOIC surface-mount package. According to the Analog Devices MAX3485E product description, these are the headline ratings engineers use to decide whether the part fits their bus topology, cable length, EMI budget and node count.

エンジニアリング参考データ: MAX3485ECSA+T — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the MAX3485ECSA+T when your design needs a 3.3 V single-supply, half-duplex RS-485/RS-422 port with a single controlled driver edge rate up to 12 Mbps and strong bus-pin ESD immunity. Choose the MAX3485CSA+ if 10 Mbps is sufficient and you want maximum family commonality with lower-cost sourcing. Choose the MAX3485ESA+T or MAX3485EESA+T when the narrower commercial temperature grade matches your ambient envelope and you prefer the family standard part number. Choose the SN75HVD11DR when node count dominates the decision, since its 1/8 unit-load option supports up to 256 nodes on the bus and it offers selectable 1, 10 and 32 Mbps driver transition times. Choose the MAX3490ECSA-T when the fail-safe and bus-recovery behaviour of that part is specifically required. In every case, re-check termination, biasing and receiver thresholds in the target bus topology before releasing a substitute into production.

代替品との比較

パラメータ この製品 MAX3485ESA+T MAX3485CSA+ MAX3490ECSA-T MAX3485EESA+T SN75HVD11DR
Package 8-SOIC (NSOIC) 8-SOIC (NSOIC) - same 8-SOIC (NSOIC) - same 8-SOIC (NSOIC) - same 8-SOIC (NSOIC) - same 8-SOIC (NSOIC) - same
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Texas Instruments
Driver / Receiver Count 1 driver, 1 receiver 1 driver, 1 receiver 1 driver, 1 receiver 1 driver, 1 receiver 1 driver, 1 receiver 1 driver, 1 receiver

主な差別化要因

  • Higher maximum data rate than the non-E MAX3485CSA+ in the same footprint (vs MAX3485CSA+)
  • No footprint change required against the closest Texas Instruments option (vs SN75HVD11DR)
  • Single fixed slew-limited driver profile simplifies EMC and signal-integrity work (vs SN75HVD11DR)
  • Direct same-family interchange with the temperature-grade ordering variants (vs MAX3485EESA+T)

設計ノート

Route Y and Z as a tightly coupled differential pair over a continuous ground plane, with the pair length matched within a few millimetres and no stubs to test points or unused pins. Keep the transceiver close to the connector so surge and ESD currents are diverted into the chassis or earth plane before they reach the logic section, and place the optional bus termination resistor directly at the driver end of the pair rather than at the transceiver.

The device runs from a single 3.3 V rail (3 V to 3.6 V), so place a 100 nF ceramic decoupling capacitor as close as possible to the VCC pin and add a bulk capacitor of roughly 1 uF to 10 uF at the supply entry point. Because the DE and /RE logic pins are driven by a microcontroller, tie them to defined states through the firmware or a pull resistor so the bus is never left floating during reset or brownout, which could otherwise produce an unintended differential pulse on the line.

The slew-rate-limited driver is the main reason this transceiver is easy to pass EMC testing, so keep that behaviour intact: do not parallel multiple transceivers onto the same bus pair to increase drive strength, and avoid adding external capacitive loads at the connector. If radiated emissions still exceed limits, first re-check that the cable shield is properly bonded and that common-mode chokes are sized for the actual data rate, rather than forcing the driver harder.

A frequent integration error is asserting DE and /RE at the same time in order to listen while transmitting, which can cause driver contention on multi-drop buses. Decide explicitly whether echo is required; otherwise hold /RE low only during receive windows and deassert DE before the last stop bit. Also verify that the transceiver ground is tied to the cable shield reference correctly, since a missing or reversed shield bond is a more frequent cause of noise problems than the transceiver itself.

コンプライアンス情報

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Yes
ハロゲンフリー
Unknown
紛争鉱物
Unknown

Manufacturer product documentation and distributor listings state RoHS3 compliant and lead free for the MAX3485ECSA+T ordering code. No AEC-Q100 qualification is claimed for this industrial interface part.

データ検証日: 2026-11-09 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

MAX3485ECSA+T MAX3485ECSA+T datasheet MAX3485ECSA+T datasheet pdf MAX3485ECSA+T pinout MAX3485E pinout and pin description MAX3485ECSA+T equivalent MAX3485ECSA+T replacement MAX3485ECSA+T vs MAX3485CSA+ MAX3485ECSA+T vs SN75HVD11DR MAX3485 12Mbps RS-485 transceiver MAX3485ECSA+T 15kV ESD RS-422 MAX3485ECSA+T 8-SOIC footprint MAX3485ECSA+T price and stock Analog Devices MAX3485ECSA+T half duplex RS-485 transceiver 3.3V SOIC-8

関連部品&用語

Analog Devices Maxim Integrated MAX3485ECSA+T MAX3485E MAX3485CSA+ MAX3485ESA+T MAX3490ECSA-T SN75HVD11DR RS-485 RS-422 transceiver half-duplex line driver differential receiver slew-rate limited ESD protection common-mode voltage bus termination UART interface SOIC-8 NSOIC package surface mount RoHS 3.3 V power supply 12 Mbps data rate
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示