Analog Devices

MAX349EAP+ - 8:1 Low-Voltage Multiplexer | Analog Devices

Teilenummer: MAX349EAP+ ✓ Aktiv
2.7 V to 16 V Vdss 100 ohms Rds(on) SSOP-20 Package
MOQ: 1 |

MAX349EAP+ Übersicht

Analog Devices MAX349EAP+ is a serially controlled, low-voltage 8-channel analog multiplexer with a maximum on-resistance of 100 ohms, supplied in a 20-pin SSOP package. It accepts single-supply operation from 2.7 V to 16 V or dual-supply operation from ±2.7 V to ±8 V. The matched on-resistance is limited to 16 ohms, with variation of no more than 10 ohms across the specified signal range.

An analog multiplexer is an interface switch that connects one of several input or output channels to a common terminal. The MAX349 belongs to the hierarchy of analog switches, multiplexers, interface ICs, and semiconductors. Its eight channels can be selected through a serial control interface, reducing the number of GPIO pins required when a controller must route multiple analog signals through a shared circuit.

The MAX349's maximum on-resistance of 100 ohms minimizes signal attenuation when it routes low-frequency analog signals. On-resistance matching between switches is specified at 16 ohms maximum, while flatness is limited to 10 ohms over the signal range. This matching helps preserve consistent signal behavior as the selected channel changes. The device also supports operation in either signal direction, allowing it to function as either a multiplexer or a demultiplexer.

The MAX349 family is intended for low-voltage equipment where analog channels must be routed through a limited number of printed-circuit-board traces. Digital control reduces routing complexity, while dual-supply support permits bipolar signal handling when paired with negative and positive rails. A single 2.7 V to 16 V supply supports lower-voltage designs where a negative rail is unnecessary.

Typical uses include multiplexed data acquisition, automated test equipment, industrial measurement systems, and portable instruments. An eight-channel arrangement is useful when several sensors, divider outputs, or control signals share a common converter input. The serial interface is particularly helpful in compact systems where conserving microcontroller or processor I/O is important.

Designers should verify signal amplitude, supply configuration, serial-interface timing, and switch behavior before assigning channels. Keep routed analog signals within the device's specified operating range, account for the 100-ohm maximum on-resistance when calculating divider ratios, and use the manufacturer's pin-description table when making PCB connections. The MAX349 and MAX350 are related dual-supply multiplexer families, but they should not be treated as interchangeable without verifying channel count and pinout.

This product page combines the official device identity, electrical characteristics, package information, application guidance, and practical replacement considerations. It also distinguishes the MAX349 from the MAX350 and explains when a verified drop-in substitute is preferable to redesigning around a different multiplexer architecture.

Drop-in-Alternativen für MAX349EAP+ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

MAX349EAP

✅ Drop-In
📦 20-pin SSOP
Same MAX349 8:1 architecture and 20-pin SSOP footprint; ordering designation differs by the + suffix, with the exact lead-finish and marking requirements requiring confirmation

📋 Referenzalternative (nicht im Katalog)

MAX349EAP+ Technische Daten

Multiplexer Configuration 8:1
Number of Channels 8 channels
Control Interface Serial
Maximum On-Resistance 100 ohms
On-Resistance Matching 16 ohms maximum
On-Resistance Flatness 10 ohms maximum
Single-Supply Voltage Range 2.7 V to 16 V
Dual-Supply Voltage Range ±2.7 V to ±8 V
Signal Conduction Direction Bidirectional
Circuit Count 1 circuit
Gehäuse SSOP-20
Montageart Surface mount

MAX349EAP+ ssop-20 Pinbelegungsleitfaden

Pinbelegung für MAX349EAP+ (ssop-20-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für MAX349EAP+ im ssop-20-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für MAX349EAP+.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

MAX349EAP+ ist geeignet für 6 Anwendungs: Multiplexed Data Acquisition, Portable Test and Measurement, Industrial Sensor Routing, Battery-Powered Sensing Modules, Programmable Signal Conditioning, Bidirectional Analog Signal Routing.

📊

Multiplexed Data Acquisition

The MAX349EAP+ fits data-acquisition boards that must route several sensor or divider outputs to a shared converter input. Its eight-channel 8:1 configuration reduces the number of direct analog connections reaching the converter, while serial control preserves controller I/O for measurements and communication. With maximum on-resistance of 100 ohms and matching limited to 16 ohms, the device is appropriate for many low-frequency measurements. The design should include input-impedance and attenuation checks so channel resistance does not degrade accuracy.

🖥️

Portable Test and Measurement

The MAX349EAP+ supports compact test instruments that need to present several measurement points to one analog front end. Its 2.7 V to 16 V single-supply range fits low-voltage portable equipment, and the serial interface reduces the number of selection lines required from the controller. Designers should account for the 100-ohm maximum channel resistance when calculating divider ratios and input loading. Control timing and the allowable analog signal range should be verified against the manufacturer datasheet before finalizing the acquisition front end.

🏭

Industrial Sensor Routing

The MAX349EAP+ is useful in industrial sensing systems that must select among multiple analog inputs before conversion or threshold evaluation. Serial control allows the controller to change channels without dedicating eight GPIO outputs, and the specified on-resistance matching of 16 ohms maximum helps maintain consistency between selected channels. The circuit must remain within the device's stated signal and supply limits. Input buffering should be added when source impedance would otherwise interact strongly with the mux's maximum 100-ohm channel resistance.

🔋

Battery-Powered Sensing Modules

The MAX349EAP+ can route multiple low-frequency sensor outputs in a low-voltage, battery-powered module. Its single-supply operation from 2.7 V to 16 V supports compact embedded systems, while the eight-channel arrangement concentrates routing into one serial-controlled device. Engineers should verify supply current in each operating state and include the 100-ohm maximum on-resistance in the signal-chain error budget. Power-saving strategies should also preserve the required control levels and avoid invalid analog conditions when channels are not selected.

🔧

Programmable Signal Conditioning

The MAX349EAP+ fits programmable signal-conditioning systems where several conditioned analog signals must reach a shared processing channel. The serial interface permits software-controlled selection while conserving processor pins, and the relatively flat resistance specification helps reduce channel-to-channel variation. The device conducts in either direction, which supports routing use cases as well as multiplexing. The analog input range, switching timing, and leakage-related limits should be checked in the datasheet, and source impedance must be high enough to avoid excessive loading through the switching path.

🌐

Bidirectional Analog Signal Routing

The MAX349EAP+ can support applications that route a common analog path among eight connections because the switches conduct equally well in either direction. This characteristic can simplify shared test paths, amplifier routing, or configurable sensor networks when the design respects the device's voltage and current limits. The 100-ohm maximum on-resistance may require gain compensation for precision measurements. Engineers should also confirm the serial-control behavior and supply arrangement from the manufacturer datasheet because the MAX350 offers a different dual four-channel pin organization.

Zusammenfassung der empfohlenen Produkte

MAX349 8-channel multiplexer family Verwendet in: Multiplexed Data Acquisition, Portable Test and Measurement, Industrial Sensor Routing, Battery-Powered Sensing Modules, Programmable Signal Conditioning, Bidirectional Analog Signal Routing MAX350 Related dual 4-channel multiplexer family Verwendet in: Multiplexed Data Acquisition, Portable Test and Measurement, Industrial Sensor Routing, Battery-Powered Sensing Modules, Programmable Signal Conditioning, Bidirectional Analog Signal Routing
What is the MAX349EAP+?
The MAX349EAP+ is a single 8:1, serially controlled, low-voltage analog multiplexer from Analog Devices. It provides eight channels, supports maximum on-resistance of 100 ohms, and operates in either signal direction. According to the Analog Devices MAX349 datasheet, on-resistance matching is 16 ohms maximum and on-resistance flatness is 10 ohms maximum across the specified signal range. The device is packaged in a 20-pin SSOP and supports both single- and dual-supply configurations.
What is the operating voltage of MAX349EAP+?
The MAX349EAP+ operates from 2.7 V to 16 V with a single supply or from ±2.7 V to ±8 V with dual supplies. These ranges appear in the Analog Devices MAX349 datasheet and product information. Single-supply operation is suitable for low-voltage systems that do not need a negative analog rail, while dual-supply operation allows bipolar signal routing when the application and board architecture support positive and negative rails.
What is the on-resistance of MAX349EAP+?
The MAX349EAP+ has a maximum on-resistance of 100 ohms. According to the Analog Devices MAX349 datasheet, the resistance between switches is matched within 16 ohms maximum, and its variation across the specified signal range is limited to 10 ohms maximum. These matching and flatness figures help maintain more consistent channel behavior when a multiplexed signal is routed through different selections.
Where can I download the MAX349EAP+ datasheet PDF?
The official MAX349 datasheet and product documentation are available from the Analog Devices MAX349 product page at https://www.analog.com/en/products/MAX349.html. Open the Data Sheet link in the documentation section to obtain the manufacturer PDF. The document contains the pin description, electrical characteristics, operating information, and multiplex configuration. Use the manufacturer document for final PCB, supply, and signal-limit decisions rather than relying on a secondary listing.
Where can I find the MAX349EAP+ pinout?
The MAX349EAP+ pinout is found in the pin-description table of the Analog Devices MAX349 datasheet. The device uses a 20-pin SSOP package, and the manufacturer document assigns each pin its control, supply, ground, or analog-channel function. Use that table when assigning PCB nets because the MAX350 family has a different channel arrangement and is not automatically a pin-for-pin substitute for the MAX349.
What can replace the MAX349EAP+?
A replacement for the MAX349EAP+ must match the 20-pin SSOP footprint, eight-channel 8:1 architecture, serial-control behavior, supply range, and signal ratings. No independently verified drop-in replacement is established for this exact MPN, so a substitute should not be selected solely from a generic cross-reference result. Check the Analog Devices MAX349 datasheet for the required interface timing and pin functions, then validate any proposed replacement against every operating condition before releasing it to production.
Is MAX349EAP+ the same as MAX350?
No. The MAX349EAP+ is an 8-channel 8:1 multiplexer, while the MAX350 is a dual 4-channel multiplexer in the related MAX349 family. The Analog Devices family description identifies both parts as serially controlled, low-voltage devices that conduct equally well in either direction. Their channel counts and pin assignments differ, so MAX350 is not a drop-in replacement for MAX349EAP+ without a documented PCB and firmware redesign.
MAX349EAP+ vs MAX350 — which is better for a multiplexed converter?
Choose the MAX349EAP+ when the design requires eight channels selected through one common path; choose the MAX350 when two independent 4-channel paths are more useful. Both belong to Analog Devices' serially controlled, low-voltage multiplexer family and support matched, relatively flat on-resistance. The MAX349 is listed with 100-ohm maximum on-resistance, 16-ohm maximum matching, and 10-ohm maximum flatness. The deciding factors are channel count, pinout, and signal architecture rather than price alone.
When should I choose MAX349EAP+ over MAX350?
Choose the MAX349EAP+ when one analog signal path must select among eight inputs, especially where conserving controller I/O is important. Its serial control reduces the number of discrete select pins, while the 100-ohm maximum on-resistance is suitable for many low-frequency measurement circuits. Choose the MAX350 instead when the board needs two separate four-channel groups. Confirm supply configuration and the complete pin mapping before deciding.
Is MAX349EAP+ suitable for battery-powered instrumentation?
The MAX349EAP+ is suitable for low-voltage instrumentation that can operate within its 2.7 V to 16 V single-supply range and that can tolerate the specified channel resistance. The Analog Devices MAX349 datasheet identifies the device as a low-voltage CMOS multiplexer with matched on-resistance. In a battery-powered design, verify actual supply current for the selected operating state, calculate the signal-path attenuation caused by the 100-ohm maximum resistance, and ensure that power-gating arrangements do not disturb controlled signals.
What are the key specifications of MAX349EAP+ that engineers should know?
The key MAX349EAP+ specifications are an 8:1 configuration, eight channels, serial control, 100-ohm maximum on-resistance, 16-ohm maximum matching, and 10-ohm maximum flatness. According to the Analog Devices MAX349 datasheet, it supports 2.7 V to 16 V single-supply operation or ±2.7 V to ±8 V dual-supply operation. It conducts signals in either direction and is offered in a 20-pin SSOP package. Signal amplitude, supply current, timing, and temperature limits should be checked in the datasheet.
What is the best Analog Devices equivalent for MAX349EAP+?
The closest documented family member is the MAX350, but it is not a drop-in equivalent because it provides dual 4-channel multiplexing rather than one 8:1 multiplexer. No verified same-package, pin-compatible equivalent is established for the exact MAX349EAP+ ordering code. For a redesign, evaluate the MAX350 when two independent channel groups solve the system architecture, but plan for pinout, control, and firmware changes rather than treating it as a component-for-component replacement.
Where can I buy MAX349EAP+ online?
Use the Request a Quote form on this page to ask for MAX349EAP+ availability, current lead time, and order handling. The Analog Devices product page identifies the MAX349 family as being in production, but that status does not by itself confirm a current lot, packaging allocation, or shipment date. Include your required quantity, date code preference, and delivery destination in the request so the quotation reflects the configuration you intend to use.
What is the price of MAX349EAP+?
Use the Request a Quote form on this page for the current MAX349EAP+ commercial quotation. Pricing depends on the ordered quantity, package or shipping configuration, date-code requirements, and current market conditions. The manufacturer product page shows a starting list price for the MAX349 family, but that family-level figure does not establish a quantity-break price for the exact MAX349EAP+ ordering code, so it should not be treated as the quotation for your order.
What is the lead time and stock status for MAX349EAP+?
Request the current lead time and stock allocation through the Request a Quote form on this page. The Analog Devices MAX349 product page lists the family as PRODUCTION, but production status does not reveal the quantity currently available for the MAX349EAP+ package code. A firm delivery commitment should therefore be obtained for the required quantity and date-code policy. Include your production schedule so the supplier can confirm the most appropriate supply plan.

Technische Referenzdaten für MAX349EAP+ – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose MAX349EAP+ when the circuit needs eight analog channels to share one common path and serial control is preferred to eight discrete select lines. It is particularly useful in low-voltage data-acquisition and test systems where the signal bandwidth and source impedance can accommodate the 100-ohm maximum channel resistance. Choose MAX350 when two independent four-channel groups are required; although it belongs to the same family, its channel count and pinout differ, so it is not a drop-in replacement. No verified pin-compatible substitute has been established for the exact MAX349EAP+ ordering code. For any proposed replacement, require the same SSOP-20 footprint, compatible serial-control timing, matching supply requirements, and equivalent analog-signal limits, then validate operation across channel, voltage, and temperature conditions.

Vergleich mit Alternativen

Parameter Dieses Produkt
Multiplexer Configuration 8:1
Number of Channels 8 channels
Maximum On-Resistance 100 ohms
On-Resistance Matching 16 ohms maximum
On-Resistance Flatness 10 ohms maximum
Single-Supply Voltage Range 2.7 V to 16 V
Dual-Supply Voltage Range ±2.7 V to ±8 V
Package SSOP-20
Brand Analog Devices

Wichtigste Unterscheidungsmerkmale

  • Eight-to-one channel organization (vs. MAX350)
  • Defined resistance matching (vs. MAX350)
  • Single- and dual-supply operation (vs. MAX350)

Designhinweise

Include the 100-ohm maximum on-resistance in the complete signal-path calculation, including source impedance, converter input impedance, and any termination network. The 16-ohm maximum matching and 10-ohm maximum flatness figures help estimate channel variation, but application accuracy still depends on the surrounding circuit. For high-impedance sources, consider buffering ahead of the multiplexer or using a lower-resistance interface architecture.

Select either the single-supply range of 2.7 V to 16 V or the dual-supply range of ±2.7 V to ±8 V according to the signal requirements. Check the supply current for each control and switching state in the manufacturer datasheet rather than estimating it. When dual supplies are used, confirm that negative-rail startup and shutdown sequences remain within the device's operating requirements, particularly if the selected analog input can exceed a rail during transitions.

Assign every SSOP-20 connection from the pin-description table in the Analog Devices MAX349 datasheet. Place the multiplexer close to the shared analog path to minimize trace resistance and susceptibility to interference. Keep sensitive analog routing away from serial-control and supply-return paths where practical, and use a continuous ground reference beneath the device. The MAX350 family has a different channel count and pin organization, so its land pattern must not be copied without verification.

Do not treat the MAX350 as a drop-in substitute for the MAX349EAP+ because one provides an 8:1 channel organization while the other provides dual 4-channel groups. Likewise, generic cross-reference tools do not establish pin compatibility, control timing, or electrical equivalence. A true replacement should require the same SSOP-20 land pattern, pin-for-pin behavior, compatible serial interface, and equivalent voltage and signal ratings, followed by circuit-level validation.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact MAX349EAP+ ordering code.

Daten verifiziert am: 2026-11-09 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

MAX349EAP+ datasheet MAX349EAP+ datasheet pdf MAX349EAP+ pinout MAX349EAP+ specifications MAX349EAP+ equivalent MAX349EAP+ replacement MAX349EAP+ cross reference MAX349EAP+ vs MAX350 MAX349EAP+ SSOP-20 footprint MAX349EAP+ 8:1 multiplexer MAX349EAP+ 100 ohm on resistance Analog Devices MAX349EAP+ MAX349EAP+ price MAX349EAP+ stock MAX349EAP+ lead time

Verwandte Bauteile & Begriffe

Analog Devices MAX349EAP+ MAX349 MAX350 8:1 analog multiplexer analog switch multiplexer demultiplexer interface IC semiconductor serial control on-resistance on-resistance matching on-resistance flatness single-supply operation dual-supply operation SSOP-20 SSOP package family surface-mount package data acquisition industrial sensor routing test and measurement signal conditioning bidirectional signal routing
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen