MAX349EAP+ - 8:1 Low-Voltage Multiplexer | Analog Devices
MPN: MAX349EAP+ ✓ 啟用中MAX349EAP+ 概覽
An analog multiplexer is an interface switch that connects one of several input or output channels to a common terminal. The MAX349 belongs to the hierarchy of analog switches, multiplexers, interface ICs, and semiconductors. Its eight channels can be selected through a serial control interface, reducing the number of GPIO pins required when a controller must route multiple analog signals through a shared circuit.
The MAX349's maximum on-resistance of 100 ohms minimizes signal attenuation when it routes low-frequency analog signals. On-resistance matching between switches is specified at 16 ohms maximum, while flatness is limited to 10 ohms over the signal range. This matching helps preserve consistent signal behavior as the selected channel changes. The device also supports operation in either signal direction, allowing it to function as either a multiplexer or a demultiplexer.
The MAX349 family is intended for low-voltage equipment where analog channels must be routed through a limited number of printed-circuit-board traces. Digital control reduces routing complexity, while dual-supply support permits bipolar signal handling when paired with negative and positive rails. A single 2.7 V to 16 V supply supports lower-voltage designs where a negative rail is unnecessary.
Typical uses include multiplexed data acquisition, automated test equipment, industrial measurement systems, and portable instruments. An eight-channel arrangement is useful when several sensors, divider outputs, or control signals share a common converter input. The serial interface is particularly helpful in compact systems where conserving microcontroller or processor I/O is important.
Designers should verify signal amplitude, supply configuration, serial-interface timing, and switch behavior before assigning channels. Keep routed analog signals within the device's specified operating range, account for the 100-ohm maximum on-resistance when calculating divider ratios, and use the manufacturer's pin-description table when making PCB connections. The MAX349 and MAX350 are related dual-supply multiplexer families, but they should not be treated as interchangeable without verifying channel count and pinout.
This product page combines the official device identity, electrical characteristics, package information, application guidance, and practical replacement considerations. It also distinguishes the MAX349 from the MAX350 and explains when a verified drop-in substitute is preferable to redesigning around a different multiplexer architecture.
直接替換替代品,適用於 MAX349EAP+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
MAX349EAP
✅ 直接替換📋 參考替代品(不在目錄中)
MAX349EAP+ 規格
| Multiplexer Configuration | 8:1 |
| Number of Channels | 8 channels |
| Control Interface | Serial |
| Maximum On-Resistance | 100 ohms |
| On-Resistance Matching | 16 ohms maximum |
| On-Resistance Flatness | 10 ohms maximum |
| Single-Supply Voltage Range | 2.7 V to 16 V |
| Dual-Supply Voltage Range | ±2.7 V to ±8 V |
| Signal Conduction Direction | Bidirectional |
| Circuit Count | 1 circuit |
| 封裝 | SSOP-20 |
| 安裝類型 | Surface mount |
MAX349EAP+ ssop-20 腳位配置指南
MAX349EAP+(ssop-20 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX349EAP+.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX349EAP+ 適用於 6 應用s: Multiplexed Data Acquisition, Portable Test and Measurement, Industrial Sensor Routing, Battery-Powered Sensing Modules, Programmable Signal Conditioning, Bidirectional Analog Signal Routing.
Multiplexed Data Acquisition
The MAX349EAP+ fits data-acquisition boards that must route several sensor or divider outputs to a shared converter input. Its eight-channel 8:1 configuration reduces the number of direct analog connections reaching the converter, while serial control preserves controller I/O for measurements and communication. With maximum on-resistance of 100 ohms and matching limited to 16 ohms, the device is appropriate for many low-frequency measurements. The design should include input-impedance and attenuation checks so channel resistance does not degrade accuracy.
推薦
Portable Test and Measurement
The MAX349EAP+ supports compact test instruments that need to present several measurement points to one analog front end. Its 2.7 V to 16 V single-supply range fits low-voltage portable equipment, and the serial interface reduces the number of selection lines required from the controller. Designers should account for the 100-ohm maximum channel resistance when calculating divider ratios and input loading. Control timing and the allowable analog signal range should be verified against the manufacturer datasheet before finalizing the acquisition front end.
推薦
Industrial Sensor Routing
The MAX349EAP+ is useful in industrial sensing systems that must select among multiple analog inputs before conversion or threshold evaluation. Serial control allows the controller to change channels without dedicating eight GPIO outputs, and the specified on-resistance matching of 16 ohms maximum helps maintain consistency between selected channels. The circuit must remain within the device's stated signal and supply limits. Input buffering should be added when source impedance would otherwise interact strongly with the mux's maximum 100-ohm channel resistance.
推薦
Battery-Powered Sensing Modules
The MAX349EAP+ can route multiple low-frequency sensor outputs in a low-voltage, battery-powered module. Its single-supply operation from 2.7 V to 16 V supports compact embedded systems, while the eight-channel arrangement concentrates routing into one serial-controlled device. Engineers should verify supply current in each operating state and include the 100-ohm maximum on-resistance in the signal-chain error budget. Power-saving strategies should also preserve the required control levels and avoid invalid analog conditions when channels are not selected.
推薦
Programmable Signal Conditioning
The MAX349EAP+ fits programmable signal-conditioning systems where several conditioned analog signals must reach a shared processing channel. The serial interface permits software-controlled selection while conserving processor pins, and the relatively flat resistance specification helps reduce channel-to-channel variation. The device conducts in either direction, which supports routing use cases as well as multiplexing. The analog input range, switching timing, and leakage-related limits should be checked in the datasheet, and source impedance must be high enough to avoid excessive loading through the switching path.
推薦
Bidirectional Analog Signal Routing
The MAX349EAP+ can support applications that route a common analog path among eight connections because the switches conduct equally well in either direction. This characteristic can simplify shared test paths, amplifier routing, or configurable sensor networks when the design respects the device's voltage and current limits. The 100-ohm maximum on-resistance may require gain compensation for precision measurements. Engineers should also confirm the serial-control behavior and supply arrangement from the manufacturer datasheet because the MAX350 offers a different dual four-channel pin organization.
推薦
推薦產品摘要
工程參考資料,適用於 MAX349EAP+ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Multiplexer Configuration | 8:1 |
| Number of Channels | 8 channels |
| Maximum On-Resistance | 100 ohms |
| On-Resistance Matching | 16 ohms maximum |
| On-Resistance Flatness | 10 ohms maximum |
| Single-Supply Voltage Range | 2.7 V to 16 V |
| Dual-Supply Voltage Range | ±2.7 V to ±8 V |
| Package | SSOP-20 |
| Brand | Analog Devices |
主要差異化特點
- Eight-to-one channel organization (對比MAX350)
- Defined resistance matching (對比MAX350)
- Single- and dual-supply operation (對比MAX350)
設計說明
Include the 100-ohm maximum on-resistance in the complete signal-path calculation, including source impedance, converter input impedance, and any termination network. The 16-ohm maximum matching and 10-ohm maximum flatness figures help estimate channel variation, but application accuracy still depends on the surrounding circuit. For high-impedance sources, consider buffering ahead of the multiplexer or using a lower-resistance interface architecture.
Select either the single-supply range of 2.7 V to 16 V or the dual-supply range of ±2.7 V to ±8 V according to the signal requirements. Check the supply current for each control and switching state in the manufacturer datasheet rather than estimating it. When dual supplies are used, confirm that negative-rail startup and shutdown sequences remain within the device's operating requirements, particularly if the selected analog input can exceed a rail during transitions.
Assign every SSOP-20 connection from the pin-description table in the Analog Devices MAX349 datasheet. Place the multiplexer close to the shared analog path to minimize trace resistance and susceptibility to interference. Keep sensitive analog routing away from serial-control and supply-return paths where practical, and use a continuous ground reference beneath the device. The MAX350 family has a different channel count and pin organization, so its land pattern must not be copied without verification.
Do not treat the MAX350 as a drop-in substitute for the MAX349EAP+ because one provides an 8:1 channel organization while the other provides dual 4-channel groups. Likewise, generic cross-reference tools do not establish pin compatibility, control timing, or electrical equivalence. A true replacement should require the same SSOP-20 land pattern, pin-for-pin behavior, compatible serial interface, and equivalent voltage and signal ratings, followed by circuit-level validation.
合規資訊
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact MAX349EAP+ ordering code.