MAX355EWE+ Dual Fault-Protected 4:1 Mux | Maxim
Teilenummer: MAX355EWE+ ✓ AktivMAX355EWE+ Übersicht
An analog multiplexer routes one of several analog inputs to an output according to digital select-control signals. The MAX355 family belongs to the analog-switch and multiplexer hierarchy, where switch resistance, channel isolation, logic levels, supply range, and fault tolerance determine whether a device is suitable for precision measurement, test equipment, battery systems, or signal-routing networks.
The MAX355EWE+ combines two 4:1 muxes in one 16-pin package. Its principal electrical characteristics include 2 circuits, 8 selectable channels, 350 ohm on-resistance, and a 4.5 V to 36 V operating supply range. The series N-channel, P-channel, N-channel switch architecture is designed to limit fault current and protect downstream circuitry during power-up, power-down, and overvoltage conditions.
Fault protection extends as much as 40 V beyond the positive and negative supply rails. This characteristic is important when an external signal may exceed the local supply range during startup or an electrical fault. The protection structure is intended to preserve sensitive measurement circuits rather than serve as a substitute for normal operating-voltage design or external surge protection.
Typical uses include battery-powered instrumentation, programmable test and measurement systems, industrial sensor acquisition, analog signal routing, and communication equipment that must select among several analog inputs. The wide 4.5 V to 36 V supply span supports both low-voltage portable systems and higher-voltage industrial signal chains.
PCB design should reserve the complete 16-pin footprint exactly as defined by the manufacturer pin description and place bypass capacitors close to the supply pins. Before substituting the device into an existing board, verify control-logic thresholds, input signal range, switch timing, and the specific operating-temperature grade.
This page combines the manufacturer product information with practical fault-protection guidance, same-footprint alternatives, sourcing instructions, and design considerations for engineers evaluating the MAX355EWE+ as a protected dual analog multiplexer.
Drop-in-Alternativen für MAX355EWE+ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MAX355EWE+ (gleiche Bauform und Footprint) – abweichend in Multiplexer Configuration, On-Resistance, Package.
MAX355CWE+T
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX355EWE+T
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX355EWE+ Technische Daten
| Multiplexer Configuration | Dual 4:1 analog multiplexer |
| Number of Circuits | 2 circuits |
| Number of Selectable Channels | 8 channels total |
| Switch Circuit Type | SP4T |
| On-Resistance | 350 ohm |
| Supply Voltage Range | 4.5 V to 36 V |
| Fault-Protection Range | Up to 40 V beyond supply rails |
| Switch Architecture | Series N-channel, P-channel, N-channel structure |
| Anzahl der Pins | 16 pins |
| Gehäuse | 16-pin WSOIC, 7.62 mm body |
| Montageart | Surface mount |
| Production Status | Production |
MAX355EWE+ 16-pin wsoic, 7.62 mm body Pinbelegungsleitfaden
Pinbelegung für MAX355EWE+ (16-pin wsoic, 7.62 mm body-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für MAX355EWE+.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MAX355EWE+ ist geeignet für 6 Anwendungs: Battery-Powered Test and Measurement, Industrial Sensor Acquisition, Programmable Analog Signal Routing, Battery Management Monitoring, Communications and Network Equipment, Automated ATE and Signal Conditioning.
Battery-Powered Test and Measurement
The MAX355EWE+ is well suited to portable measurement systems that must select among several analog inputs while the external source may temporarily exceed the local supply rails. Its two 4:1 sections provide eight selectable inputs in one 16-pin package, while 350 ohm on-resistance helps define the source impedance presented to the following amplifier. Fault protection up to 40 V beyond the supply rails adds an extra safety margin during startup, shutdown, and abnormal source conditions. The 4.5 V to 36 V operating range also permits use in both compact low-voltage equipment and higher-voltage industrial test fixtures when the selected grade meets the environmental requirements.
Empfohlen
Industrial Sensor Acquisition
The MAX355EWE+ can route outputs from multiple industrial sensors into a shared analog front end without requiring a separate multiplexer package for every channel. Two independent 4:1 sections allow simultaneous selection of two signal groups, and the 350 ohm on-resistance should be included when calculating divider ratios, ADC settling behavior, and amplifier-input loading. The device's fault-protected architecture is particularly useful when sensor inputs originate outside the local electronics supply or can experience transients during equipment startup. With a 4.5 V to 36 V supply range, the multiplexer can support both compact control electronics and industrial signal chains, subject to the signal and temperature limits of the selected grade.
Empfohlen
Programmable Analog Signal Routing
The MAX355EWE+ is appropriate for programmable analog routing where a controller must select among four sources on either multiplexer half. Digital select and enable inputs allow the same routing system to connect sensors, calibration references, or test points to a shared converter input. Its 350 ohm on-resistance is a key design parameter for high-impedance sources, while the 4.5 V to 36 V supply range supports broad industrial operating environments. The dual 4:1 organization reduces board area by combining two routing banks in one 16-pin wide SOIC package. Engineers should verify logic thresholds and switching timing against the control system, especially when the selected input can exceed the supply rails during fault recovery.
Empfohlen
Battery Management Monitoring
The MAX355EWE+ can monitor several battery-related voltages in systems where the measured source may temporarily sit outside the measurement circuitry's local supply range. Its two 4:1 sections can select separate groups of battery, current-sense, or auxiliary signals for monitoring and protection functions. The 4.5 V minimum supply supports low-energy designs, while the 36 V maximum permits use across a broad range of industrial battery architectures. Protection up to 40 V beyond the supply rails helps isolate downstream circuitry during startup or abnormal operating conditions. Designers must still ensure that every selected signal remains within the multiplexer family's specified analog input limits and that the 350 ohm on-resistance is acceptable for the measurement node.
Empfohlen
Communications and Network Equipment
The MAX355EWE+ supports analog routing in communication equipment where multiple transmit, receive, monitor, or calibration paths must be selected by control logic. Two 4:1 banks in a 16-pin wide SOIC package provide a compact routing solution for line cards and interface modules. The 4.5 V to 36 V supply span accommodates many board-level rails, and the fault-protected switch structure can limit harm to sensitive downstream circuitry when an external line is overvoltage. Signal integrity assessments should account for the specified 350 ohm on-resistance, off-isolation, and switching behavior. Because this device is an analog multiplexer rather than a high-frequency RF switch, its use is best concentrated on lower-frequency monitoring and control paths.
Empfohlen
Automated ATE and Signal Conditioning
The MAX355EWE+ is suitable for automated test equipment that routes several conditioned or raw analog nodes into a shared measurement chain. Its dual 4:1 organization permits two independently selected inputs, reducing the footprint and component count compared with separate switch packages. Fault protection up to 40 V beyond the supply rails is useful in fixtures where test-point voltages can exceed the local rails during setup or fault conditions. The 350 ohm on-resistance must be considered alongside the source impedance, ADC input capacitance, and required settling time. The 4.5 V to 36 V supply range supports broad test-system compatibility, provided the selected temperature grade and control-logic levels are appropriate for the production environment.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MAX355EWE+ – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MAX355CWE+T | MAX355EWE+T |
|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Multiplexer Configuration | Dual 4:1 analog multiplexer | Dual 4:1 analog multiplexer | Dual 4:1 analog multiplexer |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits |
| On-Resistance | 350 ohm | 350 ohm | 350 ohm |
| Supply Voltage Range | 4.5 V to 36 V | 4.5 V to 36 V | 4.5 V to 36 V |
| Fault Protection | Up to 40 V beyond supply rails | Up to 40 V beyond supply rails | Up to 40 V beyond supply rails |
| Switch Architecture | Series N-channel, P-channel, N-channel structure | Series N-channel, P-channel, N-channel structure | Series N-channel, P-channel, N-channel structure |
| Number of Pins | 16 pins | 16 pins | 16 pins |
| Surface-Mount Packaging | Yes | Yes | Yes |
Wichtigste Unterscheidungsmerkmale
- Integrated dual analog multiplexer with fault protection (vs. MAX355CWE+T)
- Direct same-footprint sourcing option (vs. MAX355EWE+T)
- Wide operating supply range for industrial signal routing (vs. MAX355CWE+T)
Designhinweise
Route each analog input directly to its associated MAX355EWE+ pin and keep the sensitive-node traces away from digital select and enable lines. Place the device close to the source or destination buffer when possible, especially when the 350 ohm on-resistance contributes materially to source impedance. Use a continuous ground reference beneath the signal path and avoid shared high-current return paths beneath the multiplexer.
Apply a local bypass capacitor from the supply pins to ground and keep its connection loop short. The MAX355EWE+ operates across 4.5 V to 36 V, so the decoupling capacitor's voltage rating and dielectric class should suit the highest rail, tolerances, and transient conditions. Confirm the logic-reference arrangement in the manufacturer pin-description table before connecting control signals from another supply domain.
Do not assume that 40 V fault protection makes every signal safe for continuous operation. Use the manufacturer input-voltage limits for normal signals and the specified fault conditions for transient protection. Also avoid substituting a generic 16-pin SOIC device solely because its package matches; the dual 4:1 channel arrangement, common terminals, select logic, and enable behavior must match the original board.
Include the 350 ohm on-resistance when designing dividers, sensor interfaces, and ADC front ends. Verify off-isolation, channel-to-channel isolation, and switching timing against the operating frequency using the manufacturer's electrical tables. For high-impedance sources, an input buffer placed close to the multiplexer can reduce sensitivity to leakage and parasitic capacitance.
Compliance-Informationen
Compliance declarations require confirmation from the manufacturer product page or the applicable declaration document for the exact orderable part number.