Maxim Integrated

MAX355EWE+ Dual Fault-Protected 4:1 Mux | Maxim

MPN: MAX355EWE+ ✓ Active
4.5 V to 36 V Vdss 350 ohm Rds(on) 16-pin WSOIC, 7.62 mm body Package
MOQ: 1 |

MAX355EWE+ Overview

The Maxim Integrated MAX355EWE+ is a dual 4:1 analog multiplexer with two independent SP4T switching circuits, a 350 ohm on-resistance, and fault protection to 40 V beyond the supply rails. It operates from 4.5 V to 36 V and is packaged in a 16-pin wide SOIC configuration for surface-mount industrial electronics.

An analog multiplexer routes one of several analog inputs to an output according to digital select-control signals. The MAX355 family belongs to the analog-switch and multiplexer hierarchy, where switch resistance, channel isolation, logic levels, supply range, and fault tolerance determine whether a device is suitable for precision measurement, test equipment, battery systems, or signal-routing networks.

The MAX355EWE+ combines two 4:1 muxes in one 16-pin package. Its principal electrical characteristics include 2 circuits, 8 selectable channels, 350 ohm on-resistance, and a 4.5 V to 36 V operating supply range. The series N-channel, P-channel, N-channel switch architecture is designed to limit fault current and protect downstream circuitry during power-up, power-down, and overvoltage conditions.

Fault protection extends as much as 40 V beyond the positive and negative supply rails. This characteristic is important when an external signal may exceed the local supply range during startup or an electrical fault. The protection structure is intended to preserve sensitive measurement circuits rather than serve as a substitute for normal operating-voltage design or external surge protection.

Typical uses include battery-powered instrumentation, programmable test and measurement systems, industrial sensor acquisition, analog signal routing, and communication equipment that must select among several analog inputs. The wide 4.5 V to 36 V supply span supports both low-voltage portable systems and higher-voltage industrial signal chains.

PCB design should reserve the complete 16-pin footprint exactly as defined by the manufacturer pin description and place bypass capacitors close to the supply pins. Before substituting the device into an existing board, verify control-logic thresholds, input signal range, switch timing, and the specific operating-temperature grade.

This page combines the manufacturer product information with practical fault-protection guidance, same-footprint alternatives, sourcing instructions, and design considerations for engineers evaluating the MAX355EWE+ as a protected dual analog multiplexer.

Drop-in alternatives for MAX355EWE+ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with MAX355EWE+ (same form factor and footprint) — differing in Multiplexer Configuration, On-Resistance, Package.

Maxim Integrated
Multiplexer Configuration: Dual 4:1
On-Resistance: 350 ohm maximum
Package: 16-SOIC, 7.50 mm width
Compare with MAX355EWE+ →

MAX355CWE+T

✅ Drop-In
📦 16-SOIC
Temperature-grade suffix changes from E to C while the dual 4:1 configuration, 350 ohm on-resistance, and 16-pin footprint are retained; key electrical difference is 0%

📋 Reference alternative (not in catalog)

MAX355EWE+T

✅ Drop-In
📦 16-SOIC
Tape-and-reel ordering suffix changes while the 4:1 configuration, 350 ohm on-resistance, and 16-pin footprint remain unchanged; key electrical difference is 0%

📋 Reference alternative (not in catalog)

MAX355EWE+ Specifications

Multiplexer Configuration Dual 4:1 analog multiplexer
Number of Circuits 2 circuits
Number of Selectable Channels 8 channels total
Switch Circuit Type SP4T
On-Resistance 350 ohm
Supply Voltage Range 4.5 V to 36 V
Fault-Protection Range Up to 40 V beyond supply rails
Switch Architecture Series N-channel, P-channel, N-channel structure
Number of Pins 16 pins
Package 16-pin WSOIC, 7.62 mm body
Mounting Type Surface mount
Production Status Production

MAX355EWE+ 16-pin wsoic, 7.62 mm body Pin Configuration Guide

Pin configuration for MAX355EWE+ (16-pin wsoic, 7.62 mm body package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

16-pin wsoic, 7.62 mm body package pinout diagram for MAX355EWE+

No detailed pinout data available for MAX355EWE+.

Refer to the datasheet for full pin configuration.

Typical Applications

MAX355EWE+ is suitable for 6 applications: Battery-Powered Test and Measurement, Industrial Sensor Acquisition, Programmable Analog Signal Routing, Battery Management Monitoring, Communications and Network Equipment, Automated ATE and Signal Conditioning.

🔧

Battery-Powered Test and Measurement

The MAX355EWE+ is well suited to portable measurement systems that must select among several analog inputs while the external source may temporarily exceed the local supply rails. Its two 4:1 sections provide eight selectable inputs in one 16-pin package, while 350 ohm on-resistance helps define the source impedance presented to the following amplifier. Fault protection up to 40 V beyond the supply rails adds an extra safety margin during startup, shutdown, and abnormal source conditions. The 4.5 V to 36 V operating range also permits use in both compact low-voltage equipment and higher-voltage industrial test fixtures when the selected grade meets the environmental requirements.

🏭

Industrial Sensor Acquisition

The MAX355EWE+ can route outputs from multiple industrial sensors into a shared analog front end without requiring a separate multiplexer package for every channel. Two independent 4:1 sections allow simultaneous selection of two signal groups, and the 350 ohm on-resistance should be included when calculating divider ratios, ADC settling behavior, and amplifier-input loading. The device's fault-protected architecture is particularly useful when sensor inputs originate outside the local electronics supply or can experience transients during equipment startup. With a 4.5 V to 36 V supply range, the multiplexer can support both compact control electronics and industrial signal chains, subject to the signal and temperature limits of the selected grade.

⚡

Programmable Analog Signal Routing

The MAX355EWE+ is appropriate for programmable analog routing where a controller must select among four sources on either multiplexer half. Digital select and enable inputs allow the same routing system to connect sensors, calibration references, or test points to a shared converter input. Its 350 ohm on-resistance is a key design parameter for high-impedance sources, while the 4.5 V to 36 V supply range supports broad industrial operating environments. The dual 4:1 organization reduces board area by combining two routing banks in one 16-pin wide SOIC package. Engineers should verify logic thresholds and switching timing against the control system, especially when the selected input can exceed the supply rails during fault recovery.

🔋

Battery Management Monitoring

The MAX355EWE+ can monitor several battery-related voltages in systems where the measured source may temporarily sit outside the measurement circuitry's local supply range. Its two 4:1 sections can select separate groups of battery, current-sense, or auxiliary signals for monitoring and protection functions. The 4.5 V minimum supply supports low-energy designs, while the 36 V maximum permits use across a broad range of industrial battery architectures. Protection up to 40 V beyond the supply rails helps isolate downstream circuitry during startup or abnormal operating conditions. Designers must still ensure that every selected signal remains within the multiplexer family's specified analog input limits and that the 350 ohm on-resistance is acceptable for the measurement node.

🌐

Communications and Network Equipment

The MAX355EWE+ supports analog routing in communication equipment where multiple transmit, receive, monitor, or calibration paths must be selected by control logic. Two 4:1 banks in a 16-pin wide SOIC package provide a compact routing solution for line cards and interface modules. The 4.5 V to 36 V supply span accommodates many board-level rails, and the fault-protected switch structure can limit harm to sensitive downstream circuitry when an external line is overvoltage. Signal integrity assessments should account for the specified 350 ohm on-resistance, off-isolation, and switching behavior. Because this device is an analog multiplexer rather than a high-frequency RF switch, its use is best concentrated on lower-frequency monitoring and control paths.

🖥️

Automated ATE and Signal Conditioning

The MAX355EWE+ is suitable for automated test equipment that routes several conditioned or raw analog nodes into a shared measurement chain. Its dual 4:1 organization permits two independently selected inputs, reducing the footprint and component count compared with separate switch packages. Fault protection up to 40 V beyond the supply rails is useful in fixtures where test-point voltages can exceed the local rails during setup or fault conditions. The 350 ohm on-resistance must be considered alongside the source impedance, ADC input capacitance, and required settling time. The 4.5 V to 36 V supply range supports broad test-system compatibility, provided the selected temperature grade and control-logic levels are appropriate for the production environment.

Recommended Products Summary

MAX355EWE+T Same electrical configuration in a tape-and-reel ordering option Used in: Battery-Powered Test and Measurement, Industrial Sensor Acquisition, Programmable Analog Signal Routing, Battery Management Monitoring, Communications and Network Equipment, Automated ATE and Signal Conditioning MAX355CWE+T Same-footprint dual multiplexer with a different temperature-grade suffix Used in: Battery-Powered Test and Measurement, Industrial Sensor Acquisition, Programmable Analog Signal Routing, Battery Management Monitoring, Communications and Network Equipment, Automated ATE and Signal Conditioning
What is the MAX355EWE+ used for?
The MAX355EWE+ is a dual 4:1 analog multiplexer used to route signals from eight analog inputs to two common outputs. According to the Maxim Integrated MAX355 product documentation, the device uses a series N-channel, P-channel, N-channel structure that provides fault protection up to 40 V beyond the supply rails during power-up, power-down, and fault conditions.
What is the supply voltage range of MAX355EWE+?
The MAX355EWE+ operates from 4.5 V to 36 V. According to the MAX355 manufacturer datasheet, this wide supply range permits use in low-voltage portable systems as well as higher-voltage industrial measurement and signal-routing equipment. The selected input and output signal voltages must remain within the limits specified for the operating grade.
How much fault protection does MAX355EWE+ provide?
The MAX355EWE+ protects downstream circuitry from overvoltage as much as 40 V beyond its supply rails. Maxim Integrated states that the MAX354 and MAX355 fault-protected multiplexers use a series N-channel, P-channel, N-channel structure to limit fault current during startup, shutdown, and abnormal voltage conditions.
What is the on-resistance of MAX355EWE+?
The MAX355EWE+ has a specified on-resistance of 350 ohm. Maxim Integrated identifies the MAX355 as a pair of 4:1 analog multiplexers with a nominal 350 ohm switch resistance. This value is important when designing divider networks, sensor interfaces, and acquisition paths where the switch contributes to the effective source impedance.
Where can I download the MAX355EWE+ datasheet?
The official MAX355EWE+ documentation is available from the Maxim Integrated product page at analog.com. The product page provides the MAX355 data sheet and selection information. Use the manufacturer pin-description table and electrical-characteristics tables to assign PCB connections, verify control thresholds, and confirm suitability for the intended voltage and temperature range.
Where is the MAX355EWE+ pinout located?
The MAX355EWE+ pinout is located in the pin-description table of the official MAX355 manufacturer data sheet. The device is offered in a 16-pin wide SOIC configuration. Assign PCB tracks from the manufacturer diagram rather than inferring connections from a generic SOIC footprint, because multiplexer enable and common-terminal assignments are specific to the device.
What is the difference between MAX355EWE+ and MAX355CWE+T?
The MAX355EWE+ and MAX355CWE+T use the same 16-pin wide SOIC footprint and retain the dual 4:1, 350 ohm multiplexer architecture. Their suffix-grade operating characteristics determine the appropriate temperature environment. Before substituting one for the other, compare the manufacturer temperature limits, lifecycle status, and grade-specific qualification requirements against the actual board requirements.
When should I choose MAX355EWE+ over a conventional analog switch?
Choose the MAX355EWE+ when inputs can exceed the local supply rails during startup, shutdown, or a fault and the downstream circuit needs protection. Its fault-protected series N-channel, P-channel, N-channel architecture tolerates overvoltage up to 40 V beyond the supply rails, making it more suitable than a conventional unprotected switch for many measurement and control applications.
Is MAX355EWE+ suitable for battery-powered instrumentation?
The MAX355EWE+ can suit battery-powered instrumentation when the operating supply remains within 4.5 V to 36 V and the selected analog signals meet the device ratings. Its 350 ohm on-resistance and dual 4:1 organization reduce the number of external switch packages needed. Power-consumption and logic-threshold details should be confirmed from the manufacturer data sheet for the exact grade.
What can replace MAX355EWE+?
The closest identified drop-in candidate is MAX355CWE+T, which retains the 16-pin wide SOIC footprint and the same dual 4:1, 350 ohm switching architecture. A valid replacement must also meet the board's supply range, logic thresholds, temperature limits, and fault-protection requirements. Review the manufacturer data sheet before approving any substitution.
Is MAX355EWE+ the same as MAX355EWE+T?
The MAX355EWE+ and MAX355EWE+T retain the same MAX355 electrical configuration, including two 4:1 circuits and 350 ohm on-resistance, in a 16-pin wide SOIC package. The ordering suffix identifies the supplier packaging format rather than a different circuit function. Verify reel orientation, moisture handling, and assembly requirements when changing the orderable part number.
What are the key specifications of MAX355EWE+ that engineers should know?
The key MAX355EWE+ specifications are a 4.5 V to 36 V supply range, 350 ohm on-resistance, two independent 4:1 switching circuits, and fault protection up to 40 V beyond the supply rails. Maxim Integrated describes the device as a production dual analog multiplexer in a 16-pin wide SOIC package. These characteristics position it for protected, multi-source analog routing.
What is the best Maxim Integrated equivalent for MAX355EWE+?
The MAX355CWE+T is the closest identified Maxim Integrated same-footprint alternative for MAX355EWE+. It preserves the 16-pin wide SOIC footprint, dual 4:1 configuration, and 350 ohm on-resistance while using a different temperature-grade suffix. Final substitution approval should compare grade limits, qualification, availability, and the exact control-pin behavior in the manufacturer data sheet.
Where can I buy MAX355EWE+ online?
Use the Request a Quote form on this page to request MAX355EWE+ availability, current commercial terms, and a lead-time quotation. The request should identify the exact MAX355EWE+ ordering code and required package quantity. Because availability and commercial conditions can change, obtain the current quantity and delivery commitment through the quotation process.
How much does MAX355EWE+ cost?
Current pricing for MAX355EWE+ should be obtained through the Request a Quote form on this page. The form allows the request to specify quantity, delivery requirements, and the exact MAX355EWE+ part number. Commercial quotations provide more useful purchasing information than a static unit-price figure because inventory, packaging, and lead time can change.
What is the lead time and stock status of MAX355EWE+?
Request the current stock status, minimum order quantity, and lead time for MAX355EWE+ through the Request a Quote form on this page. Include the required quantity, reel format, and target delivery date in the request. Maxim Integrated identifies MAX355 as a production device, but project-specific availability should be confirmed for the exact ordering suffix.

Engineering reference data for MAX355EWE+ — comparison, design guidance, and compliance information.

Selection Guide

Choose MAX355EWE+ when the design requires two 4:1 analog routing sections, 350 ohm on-resistance, and protection from inputs driven up to 40 V beyond the supply rails. The device is especially attractive for portable instrumentation, industrial sensor acquisition, automated test equipment, and analog routing where external sources may exceed the local rails during startup or faults. MAX355CWE+T is the closest same-footprint choice when its temperature grade better matches the installation environment; confirm all grade-specific limits before substitution. MAX355EWE+T offers the same core electrical characteristics in a tape-and-reel ordering format for automated assembly. None of these alternatives removes the need to check logic thresholds, analog signal limits, switch timing, and settling behavior. For designs where the package differs, a redesign is required rather than a drop-in change.

Comparison with Alternatives

Parameter This Product MAX355CWE+T MAX355EWE+T
Package 16-SOIC 16-SOIC 16-SOIC
Brand Maxim Integrated Maxim Integrated Maxim Integrated
Multiplexer Configuration Dual 4:1 analog multiplexer Dual 4:1 analog multiplexer Dual 4:1 analog multiplexer
Number of Circuits 2 circuits 2 circuits 2 circuits
On-Resistance 350 ohm 350 ohm 350 ohm
Supply Voltage Range 4.5 V to 36 V 4.5 V to 36 V 4.5 V to 36 V
Fault Protection Up to 40 V beyond supply rails Up to 40 V beyond supply rails Up to 40 V beyond supply rails
Switch Architecture Series N-channel, P-channel, N-channel structure Series N-channel, P-channel, N-channel structure Series N-channel, P-channel, N-channel structure
Number of Pins 16 pins 16 pins 16 pins
Surface-Mount Packaging Yes Yes Yes

Key Differentiators

  • Integrated dual analog multiplexer with fault protection (vs MAX355CWE+T)
  • Direct same-footprint sourcing option (vs MAX355EWE+T)
  • Wide operating supply range for industrial signal routing (vs MAX355CWE+T)

Design Notes

Route each analog input directly to its associated MAX355EWE+ pin and keep the sensitive-node traces away from digital select and enable lines. Place the device close to the source or destination buffer when possible, especially when the 350 ohm on-resistance contributes materially to source impedance. Use a continuous ground reference beneath the signal path and avoid shared high-current return paths beneath the multiplexer.

Apply a local bypass capacitor from the supply pins to ground and keep its connection loop short. The MAX355EWE+ operates across 4.5 V to 36 V, so the decoupling capacitor's voltage rating and dielectric class should suit the highest rail, tolerances, and transient conditions. Confirm the logic-reference arrangement in the manufacturer pin-description table before connecting control signals from another supply domain.

Do not assume that 40 V fault protection makes every signal safe for continuous operation. Use the manufacturer input-voltage limits for normal signals and the specified fault conditions for transient protection. Also avoid substituting a generic 16-pin SOIC device solely because its package matches; the dual 4:1 channel arrangement, common terminals, select logic, and enable behavior must match the original board.

Include the 350 ohm on-resistance when designing dividers, sensor interfaces, and ADC front ends. Verify off-isolation, channel-to-channel isolation, and switching timing against the operating frequency using the manufacturer's electrical tables. For high-impedance sources, an input buffer placed close to the multiplexer can reduce sensitivity to leakage and parasitic capacitance.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

Compliance declarations require confirmation from the manufacturer product page or the applicable declaration document for the exact orderable part number.

Data verified on: 2026-11-14 — data verified and curated by XAIPART's component engineering team

Related Searches

MAX355EWE+ datasheet MAX355EWE+ specifications MAX355EWE+ pinout MAX355EWE+ datasheet pdf MAX355EWE+ equivalent MAX355EWE+ replacement MAX355EWE+ cross reference MAX355EWE+ vs MAX355CWE+T MAX355EWE+ footprint MAX355EWE+ price MAX355EWE+ stock Maxim Integrated MAX355EWE+ MAX355 350 ohm analog multiplexer MAX355EWE+ application circuit what can replace MAX355EWE+

Related Components & Terms

Maxim Integrated MAX355EWE+ MAX355CWE+T MAX355EWE+T analog multiplexer analog switch SP4T switch 4:1 multiplexer fault-protected multiplexer N-channel MOSFET P-channel MOSFET on-resistance 350 ohm 4.5 V to 36 V 40 V fault protection 16-pin WSOIC SOIC package family surface mount industrial instrumentation battery management automated test equipment analog signal routing power management IC semiconductor
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details