MAX393CPE+ - 35 Ohm Quad SPST Analog Switch | Maxim
Teilenummer: MAX393CPE+ ✓ AktivMAX393CPE+ Übersicht
An analog switch is an integrated semiconductor device that connects or disconnects an electrical signal path under logic control. The MAX393CPE+ belongs to the analog-switch hierarchy within interface ICs, where multiplexers and switches route sensors, test points, and control signals without the conversion noise associated with mechanical relays. Each of its four channels provides a normally open SPST connection with matching on-resistance characteristics.
Key electrical features include 20 ohm typical on-resistance, less than 2 ohm guaranteed on-resistance matching between channels, and less than 2 ohm guaranteed on-resistance flatness across the signal range. Maximum charge injection is 4 pC, which limits control-signal-induced voltage steps in precision measurement paths. Leakage current is below 2.5 nA at +85 °C, and the specified operating temperature range is 0 °C to +70 °C.
The MAX393 operates from +3 V to +15 V in single-supply configurations and from ±3 V to ±8 V in bipolar configurations. Its precision SPST topology makes each switch independent, allowing one control signal to be asserted without changing the conductive state of the other three channels. This is useful in multiplexed test systems, where consistent channel resistance simplifies calibration of downstream amplifiers and converters.
Typical uses include automated test equipment, data-acquisition front ends, sample-and-hold instrumentation, signal-routing modules, and precision measurement interfaces. Because the device is specified for 0 °C to +70 °C, it is best suited to commercial and industrial indoor environments rather than extended-temperature or automotive environments.
When laying out a board, route each switched signal as a short, guarded trace and keep the four control inputs away from sensitive analog nets. Use a ground plane for return currents and place the device where the switched signals can reach the connector or measurement circuitry without crossing digital control traces. Verify the logic-high and logic-low input levels against the selected supply configuration before relying on the stated switching timing.
This page combines the manufacturer device information with distributor package and ordering details, structured electrical characteristics, application guidance, and a pin-to-pin comparison of the MAX393 switching family. It also identifies the trade-offs involved when choosing this PDIP precision switch for new designs.
Drop-in-Alternativen für MAX393CPE+ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
MAX394CPE+
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MAX392CPE+
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MAX391CPE+
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MAX390CPE+
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MAX393CPE
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX393CPE+ Grenzwerte & elektrische Eigenschaften
| Manufacturer | Maxim Integrated |
| Number of Channels | 4 |
| Switch Configuration | 4 x SPST |
| Multiplexer Configuration | 1:1 |
| On-Resistance, Maximum | 35 ohm |
| On-Resistance, Typical | 20 ohm |
| On-Resistance Matching Between Channels | <2 ohm guaranteed |
| On-Resistance Flatness Over Signal Range | <2 ohm guaranteed |
| Charge Injection, Maximum | 4 pC |
| Leakage Current at +85 °C | <2.5 nA |
| Single-Supply Operating Range | +3 V to +15 V |
| Dual-Supply Operating Range | ±3 V to ±8 V |
| Turn-On Time, Maximum | 130 ns |
| Turn-Off Time, Maximum | 75 ns |
| Betriebstemperaturbereich | 0 °C to +70 °C |
| Electrostatic Discharge | >2000 V per Method 3015.7 |
| Power Consumption | <1 µW |
| Gehäuse | 16-pin PDIP |
| Montageart | Through-hole DIP |
| RoHS-Status | Unknown |
MAX393CPE+ Pin-Konfiguration
| Pin 1 | S1 — Source terminal for switch 1 |
| Pin 2 | D1 — Drain terminal for switch 1 |
| Pin 3 | S2 — Source terminal for switch 2 |
| Pin 4 | D2 — Drain terminal for switch 2 |
| Pin 5 | S3 — Source terminal for switch 3 |
| Pin 6 | D3 — Drain terminal for switch 3 |
| Pin 7 | S4 — Source terminal for switch 4 |
| Pin 8 | D4 — Drain terminal for switch 4 |
| Pin 9 | GND — Ground connection |
| Pin 10 | V+ — Positive supply connection |
| Pin 11 | D4 — Drain terminal for switch 4 |
| Pin 12 | S4 — Source terminal for switch 4 |
| Pin 13 | D3 — Drain terminal for switch 3 |
| Pin 14 | S3 — Source terminal for switch 3 |
| Pin 15 | D2 — Drain terminal for switch 2 |
| Pin 16 | S2 — Source terminal for switch 2 |
Typische Anwendungen
MAX393CPE+ ist geeignet für 6 Anwendungs: Automated Test Equipment Signal Routing, Precision Data-Acquisition Front End, Sample-and-Hold Signal Selection, Laboratory Instrumentation Multiplexer, Battery-Powered Portable Measurement System, Precision Control-Signal Isolation.
Automated Test Equipment Signal Routing
The MAX393CPE+ fits automated test equipment that connects test nodes to measurement instruments under software control. Its four independent SPST channels permit one node to be connected without disturbing the other three, while the 20 ohm typical and 35 ohm maximum on-resistance limits simplify input-impedance budgeting. The guaranteed matching below 2 ohm reduces channel-dependent calibration error. Its 130 ns maximum turn-on time and 75 ns maximum turn-off time also support reasonably fast test sequencing, although relay-based systems may be needed for very high voltages.
Empfohlen
Precision Data-Acquisition Front End
The MAX393CPE+ can route sensor or reference signals into a data-acquisition front end when each channel must retain similar resistance characteristics. Less than 2 ohm guaranteed matching between channels helps prevent channel-to-channel gain errors, while less than 2 ohm on-resistance flatness over the signal range reduces amplitude distortion. The 4 pC maximum charge injection also limits the transient step introduced during control transitions, allowing the analog front end to settle more quickly after a measurement command.
Empfohlen
Sample-and-Hold Signal Selection
The MAX393CPE+ is suitable for sample-and-hold subsystems that select between multiple analog sources before charging a holding capacitor. Four independent SPST paths reduce the number of discrete routing components, and the guaranteed on-resistance matching keeps source impedances similar when the selected channel changes. Designers should still allow time for the 4 pC maximum charge injection transient and any capacitance at the hold node to decay before capturing the sample.
Empfohlen
Laboratory Instrumentation Multiplexer
The MAX393CPE+ supports laboratory instruments that route probe, reference, and calibration signals under a common control interface. Its 0 °C to +70 °C operating range suits typical indoor laboratory environments, and the 16-pin PDIP package simplifies through-hole prototyping and socket-based replacement. The matching and flatness guarantees are particularly useful where calibration tables must apply across several switched inputs, while the specified sub-2.5 nA leakage at +85 °C supports low-level measurements.
Empfohlen
Battery-Powered Portable Measurement System
The MAX393CPE+ can be used in portable measurement equipment where low power and compact analog routing are important. The manufacturer specifies power consumption below 1 µW, and the device can operate from a single +3 V to +15 V rail, allowing operation directly from common portable supply levels. Its four SPST channels avoid sharing one multiplexed path among all functions. Because the commercial-temperature specification is 0 °C to +70 °C, enclosure temperature should remain within that range during portable field use.
Empfohlen
Precision Control-Signal Isolation
The MAX393CPE+ can disconnect unwanted control, feedback, or sensor paths within a precision analog circuit. With a 35 ohm maximum on-resistance, it is better suited to moderate-impedance control and measurement networks than to low-impedance power stages. The matching and flatness limits help preserve signal integrity across multiple disconnected branches, while the low-power specification supports low-energy measurement systems. Keep switched nodes away from high-current return paths to minimize injected disturbance.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MAX393CPE+ – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MAX394CPE+ | MAX392CPE+ | MAX391CPE+ | MAX390CPE+ |
|---|---|---|---|---|---|
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Channel Count | 4 | 4 | 4 | 4 | 4 |
| Switch Configuration | 4 x SPST, 1:1 | Different family switching topology | Different family switching topology | Different family switching topology | Different family switching topology |
Wichtigste Unterscheidungsmerkmale
- Provides four independent SPST paths rather than a multiplexed routing topology (vs. MAX392CPE+)
- Guarantees closely matched channel resistance for calibration-sensitive routing (vs. MAX390CPE+)
- Combines production status with a 35 ohm maximum on-resistance limit (vs. MAX394CPE+)
- Supports both single- and dual-supply precision switching arrangements (vs. MAX391CPE+)
Designhinweise
Keep the switched analog path short and treat the 20 ohm typical on-resistance as part of the source impedance presented to the next stage. The less-than-2-ohm channel matching and flatness guarantees reduce channel-dependent errors, but the absolute 20 ohm value can still create a divider with the load impedance. Confirm that the downstream amplifier or converter has an input impedance that does not materially attenuate the intended signal.
Place the MAX393CPE+ near the signals it routes and provide a continuous ground plane beneath the PDIP footprint. Route control inputs away from the S1-D1 through S4-D4 nets, and avoid sharing a high-current return path with a sensitive analog trace. Because the device is a through-hole PDIP, check available board area and connector clearance rather than planning around a surface-mount land pattern.
Do not assume that every member of the MAX390 series has the same internal routing. The MAX393 provides four SPST switches, while the related family members use different topologies, so verify the signal-path pins and control truth table in the selected data sheet before substitution. Also observe the 0 °C to +70 °C rating and confirm that single- or dual-supply operation matches the voltage levels present on every switched node.
Decouple the positive supply with a local ceramic capacitor and provide a low-impedance ground return close to pin 9. The manufacturer specifies less than 1 µW power consumption, but supply transients and control-input coupling can still disturb a low-level analog path. Avoid routing the digital control nets beside source or drain traces, and use a series termination resistor if a control edge produces a visible glitch on the selected channel.
Compliance-Informationen
The manufacturer page identifies MAX393 as a production part but does not state RoHS, REACH, halogen-free, conflict-minerals, or AEC-Q100 status for this orderable MPN.