Maxim Integrated

MAX393CPE+ - 35 Ohm Quad SPST Analog Switch | Maxim

MPN: MAX393CPE+ ✓ نشط
+3 V to +15 V Vdss <2.5 nA Id 35 ohm Rds(on) 16-pin PDIP Package
الحد الأدنى للطلب: 1 |

MAX393CPE+ نظرة عامة

The Maxim Integrated MAX393CPE+ is a precision, quad SPST analog switch with four independently controlled 1:1 channels, 35 ohm maximum on-resistance, and a 16-pin PDIP package. It operates from a single +3 V to +15 V supply or from dual ±3 V to ±8 V rails. The MAX393 family supports 130 ns maximum on-time and 75 ns maximum off-time, making it suitable for precision signal routing, instrumentation, and test systems.

An analog switch is an integrated semiconductor device that connects or disconnects an electrical signal path under logic control. The MAX393CPE+ belongs to the analog-switch hierarchy within interface ICs, where multiplexers and switches route sensors, test points, and control signals without the conversion noise associated with mechanical relays. Each of its four channels provides a normally open SPST connection with matching on-resistance characteristics.

Key electrical features include 20 ohm typical on-resistance, less than 2 ohm guaranteed on-resistance matching between channels, and less than 2 ohm guaranteed on-resistance flatness across the signal range. Maximum charge injection is 4 pC, which limits control-signal-induced voltage steps in precision measurement paths. Leakage current is below 2.5 nA at +85 °C, and the specified operating temperature range is 0 °C to +70 °C.

The MAX393 operates from +3 V to +15 V in single-supply configurations and from ±3 V to ±8 V in bipolar configurations. Its precision SPST topology makes each switch independent, allowing one control signal to be asserted without changing the conductive state of the other three channels. This is useful in multiplexed test systems, where consistent channel resistance simplifies calibration of downstream amplifiers and converters.

Typical uses include automated test equipment, data-acquisition front ends, sample-and-hold instrumentation, signal-routing modules, and precision measurement interfaces. Because the device is specified for 0 °C to +70 °C, it is best suited to commercial and industrial indoor environments rather than extended-temperature or automotive environments.

When laying out a board, route each switched signal as a short, guarded trace and keep the four control inputs away from sensitive analog nets. Use a ground plane for return currents and place the device where the switched signals can reach the connector or measurement circuitry without crossing digital control traces. Verify the logic-high and logic-low input levels against the selected supply configuration before relying on the stated switching timing.

This page combines the manufacturer device information with distributor package and ordering details, structured electrical characteristics, application guidance, and a pin-to-pin comparison of the MAX393 switching family. It also identifies the trade-offs involved when choosing this PDIP precision switch for new designs.

بدائل مباشرة لـ MAX393CPE+ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

MAX394CPE+

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 16-pin PDIP
Same 16-pin PDIP family footprint, but the internal switch configuration differs from the MAX393; confirm signal-path pin assignments

📋 بديل مرجعي (غير موجود في الكتالوج)

MAX392CPE+

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 16-pin PDIP
Same 16-pin PDIP family footprint, but channel topology and control behavior differ from the four-SPST MAX393

📋 بديل مرجعي (غير موجود في الكتالوج)

MAX391CPE+

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 16-pin PDIP
Same 16-pin PDIP family footprint, but the internal routing topology differs from the MAX393

📋 بديل مرجعي (غير موجود في الكتالوج)

MAX390CPE+

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 16-pin PDIP
Same 16-pin PDIP family footprint, but the internal switching configuration differs from the MAX393

📋 بديل مرجعي (غير موجود في الكتالوج)

MAX393CPE

✅ بديل مباشر
📦 16-pin PDIP
Same MAX393 electrical configuration and 16-pin PDIP package, distinguished by the non-plus orderable designation

📋 بديل مرجعي (غير موجود في الكتالوج)

MAX393CPE+ الحدود القصوى والخصائص الكهربائية

Manufacturer Maxim Integrated
Number of Channels 4
Switch Configuration 4 x SPST
Multiplexer Configuration 1:1
On-Resistance, Maximum 35 ohm
On-Resistance, Typical 20 ohm
On-Resistance Matching Between Channels <2 ohm guaranteed
On-Resistance Flatness Over Signal Range <2 ohm guaranteed
Charge Injection, Maximum 4 pC
Leakage Current at +85 °C <2.5 nA
Single-Supply Operating Range +3 V to +15 V
Dual-Supply Operating Range ±3 V to ±8 V
Turn-On Time, Maximum 130 ns
Turn-Off Time, Maximum 75 ns
نطاق درجة حرارة التشغيل 0 °C to +70 °C
Electrostatic Discharge >2000 V per Method 3015.7
Power Consumption <1 µW
العلبة 16-pin PDIP
نوع التركيب Through-hole DIP
حالة RoHS Unknown

تكوين أطراف MAX393CPE+

DIP-16 Package Pinout Diagram DIP-16 16-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 DIP-16
دبوس 1 S1 — Source terminal for switch 1
دبوس 2 D1 — Drain terminal for switch 1
دبوس 3 S2 — Source terminal for switch 2
دبوس 4 D2 — Drain terminal for switch 2
دبوس 5 S3 — Source terminal for switch 3
دبوس 6 D3 — Drain terminal for switch 3
دبوس 7 S4 — Source terminal for switch 4
دبوس 8 D4 — Drain terminal for switch 4
دبوس 9 GND — Ground connection
دبوس 10 V+ — Positive supply connection
دبوس 11 D4 — Drain terminal for switch 4
دبوس 12 S4 — Source terminal for switch 4
دبوس 13 D3 — Drain terminal for switch 3
دبوس 14 S3 — Source terminal for switch 3
دبوس 15 D2 — Drain terminal for switch 2
دبوس 16 S2 — Source terminal for switch 2

التطبيقات النموذجية

MAX393CPE+ مناسب لـ 6 التطبيقs: Automated Test Equipment Signal Routing, Precision Data-Acquisition Front End, Sample-and-Hold Signal Selection, Laboratory Instrumentation Multiplexer, Battery-Powered Portable Measurement System, Precision Control-Signal Isolation.

🏭

Automated Test Equipment Signal Routing

The MAX393CPE+ fits automated test equipment that connects test nodes to measurement instruments under software control. Its four independent SPST channels permit one node to be connected without disturbing the other three, while the 20 ohm typical and 35 ohm maximum on-resistance limits simplify input-impedance budgeting. The guaranteed matching below 2 ohm reduces channel-dependent calibration error. Its 130 ns maximum turn-on time and 75 ns maximum turn-off time also support reasonably fast test sequencing, although relay-based systems may be needed for very high voltages.

📊

Precision Data-Acquisition Front End

The MAX393CPE+ can route sensor or reference signals into a data-acquisition front end when each channel must retain similar resistance characteristics. Less than 2 ohm guaranteed matching between channels helps prevent channel-to-channel gain errors, while less than 2 ohm on-resistance flatness over the signal range reduces amplitude distortion. The 4 pC maximum charge injection also limits the transient step introduced during control transitions, allowing the analog front end to settle more quickly after a measurement command.

🌐

Sample-and-Hold Signal Selection

The MAX393CPE+ is suitable for sample-and-hold subsystems that select between multiple analog sources before charging a holding capacitor. Four independent SPST paths reduce the number of discrete routing components, and the guaranteed on-resistance matching keeps source impedances similar when the selected channel changes. Designers should still allow time for the 4 pC maximum charge injection transient and any capacitance at the hold node to decay before capturing the sample.

🔬

Laboratory Instrumentation Multiplexer

The MAX393CPE+ supports laboratory instruments that route probe, reference, and calibration signals under a common control interface. Its 0 °C to +70 °C operating range suits typical indoor laboratory environments, and the 16-pin PDIP package simplifies through-hole prototyping and socket-based replacement. The matching and flatness guarantees are particularly useful where calibration tables must apply across several switched inputs, while the specified sub-2.5 nA leakage at +85 °C supports low-level measurements.

📱

Battery-Powered Portable Measurement System

The MAX393CPE+ can be used in portable measurement equipment where low power and compact analog routing are important. The manufacturer specifies power consumption below 1 µW, and the device can operate from a single +3 V to +15 V rail, allowing operation directly from common portable supply levels. Its four SPST channels avoid sharing one multiplexed path among all functions. Because the commercial-temperature specification is 0 °C to +70 °C, enclosure temperature should remain within that range during portable field use.

⚡

Precision Control-Signal Isolation

The MAX393CPE+ can disconnect unwanted control, feedback, or sensor paths within a precision analog circuit. With a 35 ohm maximum on-resistance, it is better suited to moderate-impedance control and measurement networks than to low-impedance power stages. The matching and flatness limits help preserve signal integrity across multiple disconnected branches, while the low-power specification supports low-energy measurement systems. Keep switched nodes away from high-current return paths to minimize injected disturbance.

ملخص المنتجات الموصى بها

MAX392CPE+ Same-family precision analog switch for alternative routing topologies يُستخدم في: Automated Test Equipment Signal Routing, Sample-and-Hold Signal Selection, Battery-Powered Portable Measurement System MAX394CPE+ Same-family precision switch for additional configuration options يُستخدم في: Automated Test Equipment Signal Routing, Laboratory Instrumentation Multiplexer MAX390CPE+ Same-family precision switch for matched routing channels يُستخدم في: Precision Data-Acquisition Front End, Battery-Powered Portable Measurement System MAX391CPE+ Same-family switching option for alternate signal routing يُستخدم في: Precision Data-Acquisition Front End, Laboratory Instrumentation Multiplexer, Precision Control-Signal Isolation MAX393CPE Related MAX393 orderable with the same core switching configuration يُستخدم في: Sample-and-Hold Signal Selection, Precision Control-Signal Isolation
What is the MAX393CPE+ and what are its main specifications?
The MAX393CPE+ is a precision, four-channel SPST analog switch in a 16-pin PDIP package. According to the Analog Devices MAX393 product page, it provides 20 ohm typical on-resistance, less than 2 ohm guaranteed matching between channels, 130 ns maximum turn-on time, and 75 ns maximum turn-off time. The device accepts single supplies from +3 V to +15 V or dual supplies from ±3 V to ±8 V.
What is the operating voltage of the MAX393CPE+?
The MAX393CPE+ operates from +3 V to +15 V in a single-supply configuration or from ±3 V to ±8 V in a bipolar configuration. The Analog Devices MAX393 product page lists both ranges, and the Mouser listing independently identifies the 3 V to 15 V single-supply limits. Select the supply arrangement that keeps every switched signal within the input voltage rating of the following circuit.
How many independent switches are built into the MAX393CPE+?
The MAX393CPE+ contains four independent SPST analog switches arranged as a 1:1 switching configuration. Each channel has its own control input, so one channel can be closed while the other three remain open. The Analog Devices MAX393 product page identifies the device as a precision, quad, SPST analog switch, and the distributor listings confirm the four-channel configuration.
What are the on-resistance and matching characteristics of the MAX393?
The MAX393 has 20 ohm typical on-resistance and a 35 ohm maximum rated on-resistance. The Analog Devices MAX393 product page also guarantees less than 2 ohm matching between channels and less than 2 ohm on-resistance flatness over the signal range. These limits help simplify calibration when several switch channels feed the same downstream amplifier or converter.
How fast does the MAX393CPE+ switch its analog signal?
The MAX393CPE+ has a maximum turn-on time of 130 ns and a maximum turn-off time of 75 ns. These values appear in the Mouser MAX393 listing and in the manufacturer's device specifications. The timing is suitable for precision test and measurement systems where the main design priority is stable channel resistance rather than ultra-high-speed multiplexing.
What is the charge injection of the MAX393CPE+ and why does it matter?
The MAX393CPE+ has a maximum charge injection of 4 pC. The Analog Devices MAX393 product page lists this figure, which describes the unwanted control-signal charge coupled into the analog path when a switch changes state. Lower charge injection is valuable in precision measurement circuits because it reduces the transient voltage step that must be settled before a reading is taken.
Where can I download the MAX393CPE+ datasheet PDF?
The official MAX393CPE+ documentation is available from the Analog Devices MAX393 product page at https://www.analog.com/en/products/max393.html. That page provides the manufacturer data sheet and product documentation, while the MAX393CPE+ listing on FindIC also provides a downloadable PDF. Use the Analog Devices document for final pin, supply, timing, and absolute-maximum-rating decisions.
Where can I find the MAX393CPE+ pinout?
The MAX393CPE+ uses a 16-pin PDIP arrangement with four source, four drain, four control, ground, and positive-supply connections. Use the pin-description table and package drawing in the Analog Devices MAX393 data sheet for final assignments. The device page at https://www.analog.com/en/products/max393.html is the appropriate starting point for the authoritative 16-pin diagram.
What is the best drop-in replacement for the MAX393CPE+?
The closest same-family drop-in choices are the MAX394CPE+, MAX392CPE+, MAX391CPE+, and MAX390CPE+, each offered in the same 16-pin PDIP format. Their internal switching configurations differ, so a drop-in decision must confirm both the physical pin assignments and the required SPST behavior. No verified cross-brand drop-in part was established for the MAX393CPE+.
Can an MAX391, MAX392, or MAX394 replace the MAX393CPE+?
The MAX391, MAX392, and MAX394 belong to the same MAX390-series precision switch family and are available in comparable PDIP packages, but they do not implement the same SPST channel arrangement as the MAX393. Treat them as same-family alternatives rather than unconditional replacements, and verify the switch configuration, control polarity, signal-path pins, and electrical limits against the original circuit.
When should I choose the MAX393CPE+ instead of another quad analog switch?
Choose the MAX393CPE+ when the design needs four independent SPST channels, low and tightly matched on-resistance, and operation from a single +3 V to +15 V rail or dual ±3 V to ±8 V rails. Its 20 ohm typical on-resistance and less than 2 ohm channel matching are attractive for instrumentation. Select another topology only if the signal path requires multiplexing, SPDT switching, or a lower-resistance device.
Is the MAX393CPE+ suitable for automotive or extended-temperature systems?
The MAX393CPE+ is not the appropriate choice for an automotive or extended-temperature design because its specified operating range is 0 °C to +70 °C. The MAX393 product page also identifies it as a production part rather than an AEC-Q100-qualified automotive device. Use a part with explicit automotive qualification and a wider temperature range when those requirements apply.
What can replace the MAX393CPE+?
A same-family replacement should first be evaluated among the MAX394CPE+, MAX392CPE+, MAX391CPE+, and MAX390CPE+ because they use the same PDIP family format. Confirm the channel topology and pin mapping before treating any of them as a drop-in replacement. Cross-brand substitutes require an equivalent 16-pin footprint, compatible logic levels, and equivalent on-resistance and leakage performance.
Is the MAX393CPE+ the same as the MAX394CPE+?
No. The MAX393CPE+ implements four SPST channels, while the MAX394CPE+ belongs to the same precision analog-switch family with a different internal switching configuration. Their shared PDIP format does not by itself establish functional interchangeability. Review the signal-path pin assignments and control truth table in each data sheet before substituting one for the other.
What are the key specifications of MAX393CPE+ that engineers should know?
The MAX393CPE+ combines four independent SPST channels with a 16-pin PDIP package, 35 ohm maximum on-resistance, and 20 ohm typical on-resistance. According to the Analog Devices product page, it guarantees less than 2 ohm matching between channels, less than 2 ohm flatness over the signal range, and 4 pC maximum charge injection. It supports +3 V to +15 V single-supply or ±3 V to ±8 V bipolar operation at 0 °C to +70 °C.
Where can I buy the MAX393CPE+ and check its availability?
Use the Request a Quote form on this page to ask about MAX393CPE+ pricing, stock, minimum order quantity, and lead time. The manufacturer product page and distributor listings identify the MAX393CPE+ as a production precision, quad, SPST analog switch. The quotation form provides a single channel for a current commercial response against the exact 16-pin PDIP orderable MPN.

بيانات مرجعية هندسية لـ MAX393CPE+ — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the MAX393CPE+ when the design requires four independent SPST channels, low and guaranteed matched on-resistance, and operation from +3 V to +15 V or ±3 V to ±8 V rails. It is particularly suitable for precision instrumentation, automated test equipment, and data-acquisition paths where channel consistency matters more than minimum on-resistance. Consider the MAX394CPE+, MAX392CPE+, MAX391CPE+, or MAX390CPE+ only after confirming that their different internal switching topologies match the intended signal routing. A related MAX393 orderable can serve the same functional requirement in the same 16-pin PDIP format. Do not select this family for AEC-Q100 automotive applications or systems operating outside 0 °C to +70 °C.

المقارنة مع البدائل

المعامل هذا المنتج MAX394CPE+ MAX392CPE+ MAX391CPE+ MAX390CPE+
Package 16-pin PDIP 16-pin PDIP 16-pin PDIP 16-pin PDIP 16-pin PDIP
Brand Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated
Channel Count 4 4 4 4 4
Switch Configuration 4 x SPST, 1:1 Different family switching topology Different family switching topology Different family switching topology Different family switching topology

أبرز الفروقات

  • Provides four independent SPST paths rather than a multiplexed routing topology (مقابلMAX392CPE+)
  • Guarantees closely matched channel resistance for calibration-sensitive routing (مقابلMAX390CPE+)
  • Combines production status with a 35 ohm maximum on-resistance limit (مقابلMAX394CPE+)
  • Supports both single- and dual-supply precision switching arrangements (مقابلMAX391CPE+)

ملاحظات التصميم

Keep the switched analog path short and treat the 20 ohm typical on-resistance as part of the source impedance presented to the next stage. The less-than-2-ohm channel matching and flatness guarantees reduce channel-dependent errors, but the absolute 20 ohm value can still create a divider with the load impedance. Confirm that the downstream amplifier or converter has an input impedance that does not materially attenuate the intended signal.

Place the MAX393CPE+ near the signals it routes and provide a continuous ground plane beneath the PDIP footprint. Route control inputs away from the S1-D1 through S4-D4 nets, and avoid sharing a high-current return path with a sensitive analog trace. Because the device is a through-hole PDIP, check available board area and connector clearance rather than planning around a surface-mount land pattern.

Do not assume that every member of the MAX390 series has the same internal routing. The MAX393 provides four SPST switches, while the related family members use different topologies, so verify the signal-path pins and control truth table in the selected data sheet before substitution. Also observe the 0 °C to +70 °C rating and confirm that single- or dual-supply operation matches the voltage levels present on every switched node.

Decouple the positive supply with a local ceramic capacitor and provide a low-impedance ground return close to pin 9. The manufacturer specifies less than 1 µW power consumption, but supply transients and control-input coupling can still disturb a low-level analog path. Avoid routing the digital control nets beside source or drain traces, and use a series termination resistor if a control edge produces a visible glitch on the selected channel.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The manufacturer page identifies MAX393 as a production part but does not state RoHS, REACH, halogen-free, conflict-minerals, or AEC-Q100 status for this orderable MPN.

تم التحقق من البيانات في: 2026-11-19 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

MAX393CPE+ datasheet MAX393CPE+ pinout MAX393CPE+ datasheet pdf MAX393CPE+ schematic MAX393CPE+ equivalent MAX393CPE+ replacement MAX393CPE+ cross reference MAX393CPE+ footprint MAX393CPE+ spice model MAX393CPE+ price MAX393CPE+ stock Maxim Integrated MAX393CPE+ MAX393CPE+ 35 ohm analog switch MAX393CPE+ vs MAX394CPE+ 16-PDIP precision quad SPST switch

المكونات والمصطلحات ذات الصلة

Maxim Integrated MAX393CPE+ MAX393 MAX394CPE+ MAX392CPE+ MAX391CPE+ MAX390CPE+ precision analog switch SPST switch 1:1 multiplexer interface IC quad analog switch on-resistance charge injection off-state leakage PDIP-16 through-hole package single-supply operation bipolar-supply operation signal routing automated test equipment data acquisition precision instrumentation
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر