MAX485ECSA+ - 2.5 Mbps RS-485 Transceiver | Analog Devices
Teilenummer: MAX485ECSA+ ✓ AktivMAX485ECSA+ Übersicht
A half-duplex transceiver is a network interface that transmits and receives data on the same differential bus pair but cannot do both simultaneously. The MAX485ECSA+ supports a multidifferential bus architecture using differential data lines for noise immunity, while its driver and receiver enable inputs allow the host to control bus direction. This device sits within the hierarchy of line transceiver, physical-layer interface IC, communication interface, and semiconductor.
Principal features include a maximum data rate of 2.5 Mbps, 15 kV ESD protection, slew-rate-limited driver outputs, and low-power operation. The E version differs from the standard MAX485C family by emphasizing electrostatic-discharge protection for industrial environments. The narrow SOIC-8 package also supports compact PCB layouts in distributed control, building automation, instrumentation, and industrial data-acquisition systems.
The transceiver uses separate active-low receiver-enable and driver-enable control inputs, permitting a connected MCU to assert the driver for transmission and release it during reception. Differential signaling improves common-mode noise rejection on long cables, but system performance still depends on correct bus termination, controlled cable characteristics, protective grounding, and an appropriate transceiver slew rate. The receiver converts the A and B differential voltage into a single-ended logic signal at the R pin.
Typical uses include industrial supervisory control, factory automation, building automation, security equipment, remote instrumentation, and RS-485 links between microcontrollers or programmable logic controllers. The MAX485ECSA+ is particularly appropriate when ESD exposure is more important than minimizing package size. For low-data-rate meter buses, lower-power or higher-node-count variants may be preferable, so protocol and bus-topology requirements should be confirmed before substitution.
The critical design consideration is bus configuration. Place termination resistors of 120 ohm at both physical ends of a standard RS-485 trunk, not at every node, and avoid star topologies with heavy loading. Use a common reference ground, controlled cable routing, and suitable surge protection for cables leaving an enclosure. The MAX485ECSA+ is a line transceiver, not a full RS-232 interface, so the host must use differential-bus-compatible logic and a suitable isolation strategy where required.
This page consolidates verified distributor availability, an identified pin-compatible cross-reference, package-level comparison data, and application-specific engineering guidance. It distinguishes the MAX485ECSA+ from related MAX485 variants based on verified package, data-rate, ESD-protection, and interface information rather than treating all similarly named transceivers as interchangeable.
Drop-in-Alternativen für MAX485ECSA+ – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MAX485ECSA+ (gleiche Bauform und Footprint) – abweichend in Package, Product Type, Technology.
MAX487EESA
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX485EESA+T
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MAX485CSA+
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
SP485ECN-L
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →MAX3485EESA+
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MAX485ECSA+ Technische Daten
| Product Type | Half-duplex RS-485/RS-422 line transceiver |
| Transceiver Configuration | 1 driver, 1 receiver |
| Technology | CMOS |
| Maximum Data Rate | 2.5 Mbps |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Interface Standard | RS-485 and RS-422 |
| Driver Output Protection | 15 kV ESD |
| Receiver Input Protection | 15 kV ESD |
| Driver Output Type | Slew-rate-limited |
| Gehäuse | 8-SOIC (0.150 inch, MS-012A) |
| Montageart | Surface Mount |
MAX485ECSA+ Pin-Konfiguration
| Pin 1 | RO — Receiver output |
| Pin 2 | /RE — Active-low receiver enable |
| Pin 3 | DE — Driver enable |
| Pin 4 | DI — Driver input |
| Pin 5 | GND — Ground |
| Pin 6 | A — Non-inverting bus terminal |
| Pin 7 | B — Inverting bus terminal |
| Pin 8 | VCC — Positive supply connection |
Typische Anwendungen
MAX485ECSA+ ist geeignet für 6 Anwendungs: Industrial PLC and Controller Networks, Building Automation and HVAC Controllers, Security and Access-Control Equipment, Remote Instrumentation and Data Acquisition, Programmable Logic Controller Communication Modules, LED Lighting and DMX-Style Control Links.
Industrial PLC and Controller Networks
The MAX485ECSA+ fits half-duplex controller-to-controller links because it combines a 2.5 Mbps maximum data rate with differential RS-485 signaling in an 8-SOIC package. Place the transceiver beside the connector, route the A and B pair as a controlled pair, and terminate the two ends of the trunk with 120 ohm resistors. The 15 kV ESD rating of the E-series device improves robustness in industrial cabinets, although field cables crossing between buildings should still receive dedicated surge protection. Verify node count, cable length, and timing margins because the transceiver rating alone does not determine link reliability.
Empfohlen
Building Automation and HVAC Controllers
The MAX485ECSA+ is appropriate for building-automation nodes where a controller communicates with actuators, sensors, and variable-air-volume units over an RS-485 backbone. Its 2.5 Mbps capability exceeds the rate normally required for supervisory HVAC commands and status data, while the narrow SOIC-8 footprint leaves board area for sensor interfaces. The 15 kV ESD protection is useful around service ports and touchable equipment. Use a common ground reference, avoid star branches, and place termination only at the physical ends of the bus to reduce reflections and loading.
Empfohlen
Security and Access-Control Equipment
The MAX485ECSA+ can connect access-control readers, controllers, and intercom equipment located in panels where electrostatic discharge is a realistic concern. Differential A and B signaling provides better immunity to common-mode noise than a single-ended link, and the E-series 15 kV ESD protection adds a useful margin around exposed connectors. The half-duplex design reduces wiring by sharing one bus pair, but firmware must coordinate the DE and active-low /RE controls so only one transmitter drives the bus at a time. Add external protection for cables routed outdoors.
Empfohlen
Remote Instrumentation and Data Acquisition
For distributed measurement stations, the MAX485ECSA+ provides a compact physical layer between a microcontroller or PLC and remote RS-485 sensors. Its verified 2.5 Mbps rate supports burst-oriented acquisition and short laboratory links without adding a separate driver IC. The 8-SOIC package fits densely populated acquisition boards, and the 15 kV ESD protection helps when operators attach external leads. Keep analog and digital grounds managed, route the differential pair away from motor and relay wiring, and follow the RS-485 recommendation of a daisy-chain trunk rather than long star branches.
Empfohlen
Programmable Logic Controller Communication Modules
The MAX485ECSA+ is suitable for RS-485 expansion ports on programmable logic controllers and remote I/O modules. Its 2.5 Mbps capability supports command traffic and fast status updates, while the half-duplex arrangement limits the interface to one shared differential pair. Designers should account for enable timing, bus turnaround dead time, and the receiver's output state during transmission. The SOIC-8 package allows the interface to be placed close to a board connector, and the E-series ESD protection improves resilience during field wiring and maintenance.
Empfohlen
LED Lighting and DMX-Style Control Links
The MAX485ECSA+ can serve as the physical interface for master-to-fixture lighting control systems that use RS-485-style differential signaling. The 2.5 Mbps rate provides ample margin for rapid fixture updates and status acknowledgements, while differential signaling helps maintain data integrity when control cables run near power wiring. Keep the transceiver close to the bus connector, use controlled pair routing, and place a 120 ohm termination at each end of the trunk. The interface does not itself implement DMX timing, addressing, or isolation, so the host controller must provide those functions.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MAX485ECSA+ – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MAX487EESA | MAX485EESA+T | MAX485CSA+ | SP485ECN-L | MAX3485EESA+ |
|---|---|---|---|---|---|---|
| Package | 8-SOIC (0.150 inch, MS-012A) | 8-SOIC - identical package | 8-SOIC | 8-SOIC | 8-SOIC - pin compatible | 8-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | MaxLinear | Analog Devices |
| Transceiver Type | 1/1 half-duplex RS-422/RS-485 transceiver | 1/1 half-duplex RS-485/RS-422 transceiver | 1/1 RS-485/RS-422 transceiver | 1/1 RS-485/RS-422 transceiver | Pin-compatible RS-485/RS-422 transceiver | 1/1 RS-485/RS-422 transceiver |
Wichtigste Unterscheidungsmerkmale
- Higher documented data rate than the non-E C-series candidate (vs. MAX485CSA+)
- ESD-focused E-series protection for industrial connector exposure (vs. MAX485CSA+)
- Documented cross-brand second source (vs. SP485ECN-L)
- Straightforward node compatibility for conventional 32-unit buses (vs. MAX487EESA)
Designhinweise
Termination belongs at the two physical ends of the main RS-485 trunk, not at every connected node. A typical implementation uses 120 ohm resistors across A and B at each end and omits termination on intermediate nodes. Avoid long star branches because their stub capacitance and inductance can produce reflections that reduce the margin of the MAX485ECSA+ at faster signaling rates.
Place the MAX485ECSA+ close to the external connector and route A and B as a tightly coupled differential pair over a continuous reference plane. Keep the pair away from relays, switching-power inductors, and high-current motor wiring. Provide a common signal-ground reference, and use a dedicated surge-protection network at the connector when the cable crosses a building boundary or connects to unprotected field equipment.
The E-series slew-rate-limited driver reduces switching transients, but firmware must still insert an appropriate bus-turnaround delay between transmission and reception because the driver may not release the bus instantly. Treat DE and /RE as directional-control signals, avoid contention with another active driver, and verify receiver output behavior while DE is asserted against the selected device's truth table.
Compliance-Informationen
The verified search excerpts do not provide direct RoHS, REACH, lead-free, or halogen-free statements for MAX485ECSA+. Compliance fields are therefore left unknown rather than inferred from the distributor pages.
