MC33990DR2 - 10.4 kbps J1850 Transceiver | NXP
Teilenummer: MC33990DR2 ✓ AktivMC33990DR2 Übersicht
An automotive serial transceiver is an interface IC that converts logic-level signals into a physical bus waveform and reconstructs valid receive data from that waveform. The MC33990DR2 belongs to the line-driver and receiver hierarchy, where it connects an automotive controller or ECU to a J1850 network while handling the voltage levels, bus contention, and noise characteristic of vehicle wiring. SAE J1850 Class B is the network specification identified for this device.
The principal operating characteristics are a 10.4 kbps data rate, a 9 V to 16 V supply range, and 200 mV receiver hysteresis. The 200 mV hysteresis helps the receiver distinguish signal states when noise or slow transitions appear on the bus. Its single half-duplex transceiver arrangement allows the same bus connection to transmit and receive, although software or hardware must ensure that only one node drives the network at a time.
The MC33990DR2 is packaged in an 8-pin SOIC for surface-mount assembly and is identified as an automotive-temperature-grade part. Its principal role is to provide a compact physical-layer interface between an automotive electronic control unit and a J1850 Class B network. The half-duplex topology supports body and powertrain systems where distributed modules share a low-speed diagnostic or communication backbone.
Typical uses include powertrain control modules, body control modules, instrument clusters, engine controllers, and vehicle diagnostic interfaces. In these systems, the transceiver can carry messages between ECUs while providing stronger signal conditioning than a general-purpose logic interface. Its dedicated network function reduces the need for separate transmit and receive circuitry at the ECU.
Design the bus connection with the recommended network termination, protection, and decoupling arrangements from the NXP datasheet. Because vehicle networks can experience transients and wiring faults, verify the external protection network, logic-level compatibility, and grounding strategy rather than relying only on the IC's operating-voltage range. The 8-pin SOIC footprint also requires adequate copper spacing and thermal consideration for automotive temperature conditions.
This product page combines the device's electrical operating limits with application guidance, practical interface considerations, a qualified comparison framework, and sourcing information for engineers designing a J1850 Class B node.
Drop-in-Alternativen für MC33990DR2 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MC33990DR2 (gleiche Bauform und Footprint) – abweichend in Temperature Grade.
Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.
Alternativen anfordernMC33990DR2 Technische Daten
| Product Type | Half-duplex serial transceiver |
| Transceiver Configuration | 1 transmitter and 1 receiver |
| Communication Mode | Half-duplex |
| Network Standard | SAE J1850 Class B |
| Maximum Data Rate | 10.4 kbps |
| Supply Voltage Range | 9 V to 16 V |
| Receiver Hysteresis | 200 mV |
| Gehäuse | 8-pin SOIC |
| Terminal Count | 8 pins |
| Montageart | Surface mount |
| Temperature Grade | Automotive |
| Lead Form | Gull wing |
| Package Shape | Rectangular |
MC33990DR2 rectangular Pinbelegungsleitfaden
Pinbelegung für MC33990DR2 (rectangular-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für MC33990DR2.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MC33990DR2 ist geeignet für 6 Anwendungs: Powertrain Control Module J1850 Interface, Body Control Module Network Node, Vehicle Diagnostic Interface, Engine Management ECU, Instrument Cluster Communication, Automotive Service Test Equipment.
Powertrain Control Module J1850 Interface
The MC33990DR2 fits a powertrain controller that must exchange low-speed diagnostic or status messages over a SAE J1850 Class B network. Its 10.4 kbps half-duplex architecture lets one controller node both transmit requests and receive responses through the same physical bus connection. Operating from 9 V to 16 V aligns with conventional 12 V vehicle power systems, while the 200 mV receiver hysteresis improves state recognition under vehicle wiring noise. The controller should ensure that only one node drives the bus at a time and should implement the timing and arbitration behavior expected by the network. External bus protection and grounding must be designed around the NXP application circuit rather than inferred solely from the 8-pin SOIC footprint.
Empfohlen
Body Control Module Network Node
The MC33990DR2 is appropriate for a body control module that shares a Class B vehicle network with door, lighting, climate, or seat controllers. The single half-duplex interface reduces the number of external bus-driver components needed for each node and supports bidirectional message exchange at 10.4 kbps. Its 9 V to 16 V operating range is suited to regulated automotive supplies, while receiver hysteresis helps the module interpret a signal disturbed by wiring noise. Because the network is shared, the body controller must obey J1850 arbitration rules and avoid transmissions that overlap another node's message. Validate the ECU power source, connector transients, ground offset, and bus termination against the NXP manufacturer datasheet during hardware qualification.
Empfohlen
Vehicle Diagnostic Interface
The MC33990DR2 can serve as the physical-layer interface in an automotive diagnostic gateway or service equipment node communicating through a SAE J1850 Class B backbone. The device transmits diagnostic requests, receives responses, and provides a defined 10.4 kbps communication rate for a half-duplex bus. Its 200 mV receiver hysteresis supports dependable recognition of the bus level in electrically noisy vehicle environments, while the 9 V to 16 V supply range supports automotive power rails. Diagnostic software must handle request prioritization, message timing, node coexistence, and bus inactivity behavior. The interface circuit should also include the protection and conditioning recommended by NXP, especially when service equipment connects through long external cables or poorly controlled vehicle wiring.
Empfohlen
Engine Management ECU
The MC33990DR2 is suitable for an engine-management ECU that communicates supervisory or diagnostic information over a J1850 Class B network. At 10.4 kbps, it supports the low-speed network role identified for this transceiver rather than high-bandwidth engine sensor streaming. The integrated transmitter and receiver provide a compact half-duplex connection, and the 200 mV hysteresis helps reject noise present on long harness runs. The ECU should coordinate access with other modules and maintain signal timing that complies with the network specification. Automotive qualification must include transient immunity, ground-bounce behavior, temperature extremes, and connector fault conditions. The design should follow the NXP recommended network interface and decoupling arrangement so that protection components do not distort the specified bus waveform.
Empfohlen
Instrument Cluster Communication
The MC33990DR2 can connect an instrument cluster or status-display controller to a J1850 Class B vehicle network. The cluster may need to transmit short control or diagnostic messages while receiving data from other modules, which matches the device's half-duplex 1-transceiver, 1-receiver configuration. The specified 10.4 kbps rate is appropriate for low-speed network traffic, and the 200 mV hysteresis improves transition recognition in the presence of harness noise. The display controller should enforce bus arbitration and message timing to prevent contention. Review the available indicator, warning, or service functions in an early architecture decision because they may require a different data interface. For the J1850 physical layer, use the NXP application information to select bus protection, grounding, and connector components.
Empfohlen
Automotive Service Test Equipment
The MC33990DR2 is useful in compact J1850 Class B service tools that connect to a vehicle network for diagnostics. The device provides a compact half-duplex interface for transmitting service requests and receiving responses at 10.4 kbps. Its 9 V to 16 V operating range supports automotive supply environments, and the 200 mV receiver hysteresis improves noise tolerance on connected harnesses. The test equipment should include current-limited protection and controlled bus access so that it cannot interfere with active vehicle modules. Communication software must manage timing, acknowledgments, and node contention in accordance with the J1850 network requirements. For production use, evaluate cable transients, ESD exposure, and connector grounding because external service cables can expose the interface to conditions that differ from an internal ECU installation.
Empfohlen
Technische Referenzdaten für MC33990DR2 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt |
|---|---|
| Package | 8-pin SOIC |
| Brand | NXP Semiconductors |
| Product Type | Half-duplex serial transceiver |
| Network Standard | SAE J1850 Class B |
| Data Rate | 10.4 kbps |
| Supply Voltage Range | 9 V to 16 V |
| Receiver Hysteresis | 200 mV |
| Temperature Grade | Automotive |
Wichtigste Unterscheidungsmerkmale
- Purpose-built J1850 Class B physical layer (vs. Generic RS-485 transceiver)
- Compact bidirectional bus connection (vs. Separate transmitter and receiver implementation)
- Noise-tolerant receiver threshold (vs. Receiver without specified hysteresis)
Designhinweise
Place the transceiver and its input/output decoupling network close to the associated supply and ground pins. Keep the printed-circuit-board return path short and provide a clean ground reference for the bus interface. Follow the component and layout recommendations in the NXP manufacturer datasheet when placing the transceiver relative to connector protection devices; excessive trace length or inductance can degrade automotive transient performance.
Do not substitute a generic half-duplex transceiver solely because it also has eight pins. Confirm the SAE J1850 Class B waveform, 10.4 kbps timing, 9 V to 16 V supply range, receiver threshold, logic levels, and connector pin assignment. A package-compatible device can still be electrically incompatible, and changing the footprint without matching these functions can cause bus contention or unreliable reception.
Treat the vehicle wiring as a potentially noisy and electrically harsh environment. Use the protection and bus-conditioning network shown in the NXP manufacturer datasheet, maintain a low-impedance ground connection, and verify conducted emissions and transient immunity at the complete ECU level. The receiver's 200 mV hysteresis helps reject noise but cannot compensate for incorrect grounding, unsuitable termination, or an unprotected connector path.
Design the ECU supply around the MC33990DR2's 9 V to 16 V operating range and account for load-dump, reverse-battery, and inductive transient conditions at the wiring boundary. Separate the transceiver's supply path from noisy actuator drivers where practical, and validate the regulator's startup, output ripple, and behavior during bus contention. These checks belong at the ECU power and connector level rather than around the IC alone.
Compliance-Informationen
The part is identified as automotive-temperature-grade, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was established for MC33990DR2.