NXP Semiconductors

MC33990DR2 - 10.4 kbps J1850 Transceiver | NXP

MPN: MC33990DR2 ✓ Nakahanda
9 V to 16 V Vdss 8-pin SOIC Package
MOQ: 1 |

MC33990DR2 Ulas

The NXP Semiconductors MC33990DR2 is a half-duplex J1850 serial transceiver for automotive Class B data networks, operating at 10.4 kbps from a 9 V to 16 V supply in an 8-pin SOIC package. It combines a transmitter, receiver, and bus interface in one device, providing bidirectional communication over a shared vehicle network.

An automotive serial transceiver is an interface IC that converts logic-level signals into a physical bus waveform and reconstructs valid receive data from that waveform. The MC33990DR2 belongs to the line-driver and receiver hierarchy, where it connects an automotive controller or ECU to a J1850 network while handling the voltage levels, bus contention, and noise characteristic of vehicle wiring. SAE J1850 Class B is the network specification identified for this device.

The principal operating characteristics are a 10.4 kbps data rate, a 9 V to 16 V supply range, and 200 mV receiver hysteresis. The 200 mV hysteresis helps the receiver distinguish signal states when noise or slow transitions appear on the bus. Its single half-duplex transceiver arrangement allows the same bus connection to transmit and receive, although software or hardware must ensure that only one node drives the network at a time.

The MC33990DR2 is packaged in an 8-pin SOIC for surface-mount assembly and is identified as an automotive-temperature-grade part. Its principal role is to provide a compact physical-layer interface between an automotive electronic control unit and a J1850 Class B network. The half-duplex topology supports body and powertrain systems where distributed modules share a low-speed diagnostic or communication backbone.

Typical uses include powertrain control modules, body control modules, instrument clusters, engine controllers, and vehicle diagnostic interfaces. In these systems, the transceiver can carry messages between ECUs while providing stronger signal conditioning than a general-purpose logic interface. Its dedicated network function reduces the need for separate transmit and receive circuitry at the ECU.

Design the bus connection with the recommended network termination, protection, and decoupling arrangements from the NXP datasheet. Because vehicle networks can experience transients and wiring faults, verify the external protection network, logic-level compatibility, and grounding strategy rather than relying only on the IC's operating-voltage range. The 8-pin SOIC footprint also requires adequate copper spacing and thermal consideration for automotive temperature conditions.

This product page combines the device's electrical operating limits with application guidance, practical interface considerations, a qualified comparison framework, and sourcing information for engineers designing a J1850 Class B node.

Mga alternatibo na pwedeng ilagay na MC33990DR2 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok MC33990DR2 (parehas na form factor at footprint) — pagkakaiba sa Temperature Grade.

NXP Semiconductors
Temperature Grade: Automotive (AEC-Q100)
Ikabit sa MC33990DR2 →

Wala ng magagamit na drop-in alternatibo para sa produkto na ito.

Hilingin ang Alternatibo

MC33990DR2 Mga Spesipikasyon

Product Type Half-duplex serial transceiver
Transceiver Configuration 1 transmitter and 1 receiver
Communication Mode Half-duplex
Network Standard SAE J1850 Class B
Maximum Data Rate 10.4 kbps
Supply Voltage Range 9 V to 16 V
Receiver Hysteresis 200 mV
Packhaging 8-pin SOIC
Terminal Count 8 pins
Uri ng Pagpapasok Surface mount
Temperature Grade Automotive
Lead Form Gull wing
Package Shape Rectangular

Gabay sa Pin Configuration ng MC33990DR2 rectangular

Pin configuration para sa MC33990DR2 (rectangular package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.

Pinout diagram ng rectangular package para sa MC33990DR2

Wala ng detalyadong pinout data na magagamit para sa MC33990DR2.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

MC33990DR2 ay nararapat para sa 6 aplikasyons: Powertrain Control Module J1850 Interface, Body Control Module Network Node, Vehicle Diagnostic Interface, Engine Management ECU, Instrument Cluster Communication, Automotive Service Test Equipment.

🚗

Powertrain Control Module J1850 Interface

The MC33990DR2 fits a powertrain controller that must exchange low-speed diagnostic or status messages over a SAE J1850 Class B network. Its 10.4 kbps half-duplex architecture lets one controller node both transmit requests and receive responses through the same physical bus connection. Operating from 9 V to 16 V aligns with conventional 12 V vehicle power systems, while the 200 mV receiver hysteresis improves state recognition under vehicle wiring noise. The controller should ensure that only one node drives the bus at a time and should implement the timing and arbitration behavior expected by the network. External bus protection and grounding must be designed around the NXP application circuit rather than inferred solely from the 8-pin SOIC footprint.

🚗

Body Control Module Network Node

The MC33990DR2 is appropriate for a body control module that shares a Class B vehicle network with door, lighting, climate, or seat controllers. The single half-duplex interface reduces the number of external bus-driver components needed for each node and supports bidirectional message exchange at 10.4 kbps. Its 9 V to 16 V operating range is suited to regulated automotive supplies, while receiver hysteresis helps the module interpret a signal disturbed by wiring noise. Because the network is shared, the body controller must obey J1850 arbitration rules and avoid transmissions that overlap another node's message. Validate the ECU power source, connector transients, ground offset, and bus termination against the NXP manufacturer datasheet during hardware qualification.

🔧

Vehicle Diagnostic Interface

The MC33990DR2 can serve as the physical-layer interface in an automotive diagnostic gateway or service equipment node communicating through a SAE J1850 Class B backbone. The device transmits diagnostic requests, receives responses, and provides a defined 10.4 kbps communication rate for a half-duplex bus. Its 200 mV receiver hysteresis supports dependable recognition of the bus level in electrically noisy vehicle environments, while the 9 V to 16 V supply range supports automotive power rails. Diagnostic software must handle request prioritization, message timing, node coexistence, and bus inactivity behavior. The interface circuit should also include the protection and conditioning recommended by NXP, especially when service equipment connects through long external cables or poorly controlled vehicle wiring.

🚗

Engine Management ECU

The MC33990DR2 is suitable for an engine-management ECU that communicates supervisory or diagnostic information over a J1850 Class B network. At 10.4 kbps, it supports the low-speed network role identified for this transceiver rather than high-bandwidth engine sensor streaming. The integrated transmitter and receiver provide a compact half-duplex connection, and the 200 mV hysteresis helps reject noise present on long harness runs. The ECU should coordinate access with other modules and maintain signal timing that complies with the network specification. Automotive qualification must include transient immunity, ground-bounce behavior, temperature extremes, and connector fault conditions. The design should follow the NXP recommended network interface and decoupling arrangement so that protection components do not distort the specified bus waveform.

📺

Instrument Cluster Communication

The MC33990DR2 can connect an instrument cluster or status-display controller to a J1850 Class B vehicle network. The cluster may need to transmit short control or diagnostic messages while receiving data from other modules, which matches the device's half-duplex 1-transceiver, 1-receiver configuration. The specified 10.4 kbps rate is appropriate for low-speed network traffic, and the 200 mV hysteresis improves transition recognition in the presence of harness noise. The display controller should enforce bus arbitration and message timing to prevent contention. Review the available indicator, warning, or service functions in an early architecture decision because they may require a different data interface. For the J1850 physical layer, use the NXP application information to select bus protection, grounding, and connector components.

🔧

Automotive Service Test Equipment

The MC33990DR2 is useful in compact J1850 Class B service tools that connect to a vehicle network for diagnostics. The device provides a compact half-duplex interface for transmitting service requests and receiving responses at 10.4 kbps. Its 9 V to 16 V operating range supports automotive supply environments, and the 200 mV receiver hysteresis improves noise tolerance on connected harnesses. The test equipment should include current-limited protection and controlled bus access so that it cannot interfere with active vehicle modules. Communication software must manage timing, acknowledgments, and node contention in accordance with the J1850 network requirements. For production use, evaluate cable transients, ESD exposure, and connector grounding because external service cables can expose the interface to conditions that differ from an internal ECU installation.

What is the MC33990DR2?
The MC33990DR2 is an NXP half-duplex serial transceiver designed for SAE J1850 Class B automotive networks. It combines one transmitter and one receiver in an 8-pin SOIC package, supports bidirectional communication at 10.4 kbps, and operates from a 9 V to 16 V supply. The NXP manufacturer datasheet identifies it as an enhanced Class B serial transceiver for vehicle communication networks.
What are the key specifications of MC33990DR2 that engineers should know?
The MC33990DR2 combines a 10.4 kbps data rate, a 9 V to 16 V supply range, and 200 mV receiver hysteresis in an 8-pin SOIC package. It is a half-duplex 1-transceiver, 1-receiver device intended for SAE J1850 Class B automotive networks. According to the NXP manufacturer datasheet, these characteristics position it for low-speed vehicle communication interfaces that require bidirectional bus access.
What is the operating voltage of MC33990DR2?
The MC33990DR2 operates from 9 V to 16 V. This supply range applies to the device's automotive bus interface and supports use in 12 V vehicle electrical systems where regulated power remains within the specified limits. The NXP manufacturer datasheet should be used for the exact supply, ground, and absolute-maximum ratings when designing the ECU power architecture.
What is the data rate of MC33990DR2?
The MC33990DR2 supports a maximum data rate of 10.4 kbps. This rate matches the low-speed communication class used by the SAE J1850 Class B application identified in the NXP manufacturer datasheet. Since the interface is half-duplex, only one node should actively transmit at a time, and the system must account for bus arbitration when scheduling network messages.
Where can I download the MC33990DR2 datasheet PDF?
The MC33990DR2 datasheet can be downloaded from the official NXP documentation page using the product link on this page. The document contains the recommended application circuit, electrical characteristics, bus timing, and pin descriptions needed for design review. Use the NXP manufacturer datasheet as the controlling source for wiring, decoupling, and external protection details.
Where can I find the MC33990DR2 pinout?
The MC33990DR2 pinout is documented in the pin-description section of the NXP manufacturer datasheet. The device uses an 8-pin SOIC package with gull-wing leads. Use the datasheet pin table when assigning the transceiver bus connection, supply, ground, logic input, and logic output because a physical drawing alone does not establish signal direction or electrical limits.
Is the MC33990DR2 suitable for automotive J1850 networks?
The MC33990DR2 is specifically suited to automotive SAE J1850 Class B communication networks. It is listed as an automotive-temperature-grade part, operates at 10.4 kbps, and provides a single half-duplex transceiver. Confirm the complete ECU electrical environment, including transient protection and node behavior, against the NXP manufacturer datasheet before production release.
What does 200 mV receiver hysteresis mean for MC33990DR2?
The MC33990DR2 receiver uses 200 mV hysteresis to distinguish valid logic states on a noisy or slowly changing bus signal. The threshold shift helps prevent repeated state transitions around a decision point. According to the NXP manufacturer datasheet, this feature supports reliable reception on automotive Class B networks, although system-level signal integrity and bus termination still require validation.
MC33990DR2 vs MC1489NG4: which is better for a J1850 bus?
The MC33990DR2 is the better choice for an SAE J1850 Class B bus because it is explicitly designed as a 10.4 kbps half-duplex J1850 transceiver. The MC1489NG4 is listed as a separate NXP interface device, but its J1850 compatibility cannot be established from the available product information. Confirm the candidate's protocol, supply range, pinout, and bus impedance before considering it.
What is the difference between MC33990DR2 and a generic RS-485 transceiver?
The MC33990DR2 is designed for SAE J1850 Class B operation, including a specified 10.4 kbps rate and 200 mV receiver hysteresis, whereas a generic RS-485 transceiver may use different thresholds, timing, and protection assumptions. Because J1850 and RS-485 are not automatically electrically interchangeable, verify the bus voltage, termination method, signaling waveform, and pin assignment against the applicable manufacturer datasheet.
When should I choose MC33990DR2 over another bus transceiver?
Choose the MC33990DR2 when the design must connect an ECU to a SAE J1850 Class B network and needs a 10.4 kbps half-duplex physical-layer interface. It is preferable to a generic transceiver only when the protocol, supply range, logic levels, bus waveform, and pin functions match. A device intended for a different automotive or RS-485 bus should not be selected solely by package size.
Is MC33990DR2 suitable for a bidirectional ECU communication link?
The MC33990DR2 supports bidirectional, half-duplex communication on a shared SAE J1850 Class B network. One transmitter and one receiver are integrated into each device, but the attached controller must coordinate bus access so that nodes do not drive the bus simultaneously. Bus timing, node priority, and fault behavior should follow the network specification and the NXP manufacturer datasheet.
What can replace MC33990DR2?
No verified pin-compatible drop-in replacement for the MC33990DR2 was identified in the available cross-reference information. A valid replacement must match the 8-pin SOIC footprint, SAE J1850 Class B electrical behavior, 10.4 kbps timing, 9 V to 16 V supply range, bus impedance, and pin functions. Do not treat a transceiver with the same package count as a drop-in device without a manufacturer-confirmed cross-reference.
What is the best cross-brand equivalent for MC33990DR2?
No cross-brand equivalent can be recommended responsibly for the MC33990DR2 because the available information does not establish pin and parameter compatibility for a specific candidate. A suitable cross-brand device would need the same 8-pin SOIC lead assignment and equivalent SAE J1850 Class B operation at 10.4 kbps. Confirm the candidate through its manufacturer datasheet and application information before changing the PCB.
Where can I buy MC33990DR2 and check its price?
Use the Request a Quote form on this page to request MC33990DR2 availability, current commercial terms, and lead time. The form allows the request to be associated with the exact manufacturer part number and package. Confirm the orderable suffix, quantity, and current lifecycle status before authorizing procurement.

Impormasyon ng Talumpati sa Engineering for MC33990DR2 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose the MC33990DR2 when an ECU must connect to an SAE J1850 Class B network and requires a compact half-duplex interface at 10.4 kbps. Its 9 V to 16 V supply range, 200 mV receiver hysteresis, and 8-pin SOIC package fit conventional 12 V vehicle-network designs. Do not select it for CAN, LIN, RS-485, or another protocol unless the physical layer has been proven equivalent. No verified drop-in substitute was identified, so a proposed alternative must match the J1850 waveform, timing, logic levels, bus impedance, supply range, and exact pin functions. Keep the existing PCB when changing parts, and validate transient protection, grounding, arbitration, and communication timing on production-representative harnesses.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto
Package 8-pin SOIC
Brand NXP Semiconductors
Product Type Half-duplex serial transceiver
Network Standard SAE J1850 Class B
Data Rate 10.4 kbps
Supply Voltage Range 9 V to 16 V
Receiver Hysteresis 200 mV
Temperature Grade Automotive

Pangunahing mga Pagkakaiba

  • Purpose-built J1850 Class B physical layer (kumpara saGeneric RS-485 transceiver)
  • Compact bidirectional bus connection (kumpara saSeparate transmitter and receiver implementation)
  • Noise-tolerant receiver threshold (kumpara saReceiver without specified hysteresis)

Talaan ng Disenyo

Place the transceiver and its input/output decoupling network close to the associated supply and ground pins. Keep the printed-circuit-board return path short and provide a clean ground reference for the bus interface. Follow the component and layout recommendations in the NXP manufacturer datasheet when placing the transceiver relative to connector protection devices; excessive trace length or inductance can degrade automotive transient performance.

Do not substitute a generic half-duplex transceiver solely because it also has eight pins. Confirm the SAE J1850 Class B waveform, 10.4 kbps timing, 9 V to 16 V supply range, receiver threshold, logic levels, and connector pin assignment. A package-compatible device can still be electrically incompatible, and changing the footprint without matching these functions can cause bus contention or unreliable reception.

Treat the vehicle wiring as a potentially noisy and electrically harsh environment. Use the protection and bus-conditioning network shown in the NXP manufacturer datasheet, maintain a low-impedance ground connection, and verify conducted emissions and transient immunity at the complete ECU level. The receiver's 200 mV hysteresis helps reject noise but cannot compensate for incorrect grounding, unsuitable termination, or an unprotected connector path.

Design the ECU supply around the MC33990DR2's 9 V to 16 V operating range and account for load-dump, reverse-battery, and inductive transient conditions at the wiring boundary. Separate the transceiver's supply path from noisy actuator drivers where practical, and validate the regulator's startup, output ripple, and behavior during bus contention. These checks belong at the ECU power and connector level rather than around the IC alone.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The part is identified as automotive-temperature-grade, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was established for MC33990DR2.

Data napatotohanan sa: 2026-11-16 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

MC33990DR2 MC33990DR2 datasheet MC33990DR2 datasheet pdf MC33990DR2 pinout MC33990DR2 schematic MC33990DR2 equivalent MC33990DR2 replacement MC33990DR2 price MC33990DR2 stock NXP MC33990DR2 J1850 MC33990DR2 automotive transceiver MC33990DR2 SOIC-8 pinout

Mga kaugnay na Mga Komponente at mga Tuntunin

NXP Semiconductors MC33990DR2 MC1489NG4 half-duplex serial transceiver line driver and receiver interface IC SAE J1850 J1850 Class B automotive network 10.4 kbps 9 V to 16 V 200 mV receiver hysteresis 8-pin SOIC SOIC family surface-mount package ECU powertrain control module body control module vehicle diagnostics bus contention automotive transient protection half-duplex communication bidirectional bus interface
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ