MC34PF4210A0ES - i.MX 8M PMIC, 14-Ch, 56-QFN | NXP
Teilenummer: MC34PF4210A0ES ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $9.85 | $9,85 |
| 10 | $8.92 | $89,20 |
| 100 | $7.74 | $774,00 |
| 500 | $6.95 | $3.475,00 |
| 1.000 | $6.18 | $6.180,00 |
MC34PF4210A0ES Übersicht
A Power Management IC (PMIC) is a highly integrated semiconductor that consolidates multiple voltage regulators, supervision circuitry, sequencing logic, and monitoring ADCs into one package, replacing dozens of discrete components around an applications processor. Within the broader taxonomy, a PMIC belongs to the Power Management category, sitting alongside discrete regulators, supervisors, and battery management ICs. The PF4210 sits at the system-power heart of audio/video platforms, providing all processor rails, peripheral voltages, and I/O supplies from a single battery or 5V input.
Key features include adjustable current limiting on each output, adjustable soft-start, dynamic voltage scaling (DVS) for adaptive processor performance, on-board power-on timing control, and overcurrent protection. Programmed via one-time programmable (OTP) memory, the A0ES variant ships with NXP factory-default settings and supports full I2C control for runtime reconfiguration. The integration of 14 rails plus telemetry reduces BOM count and PCB area while improving power-rail accuracy versus discrete regulator designs.
Architecturally, the PF4210 pairs high-frequency synchronous buck controllers with low-dropout linear post-regulators, allowing low-ripple voltage delivery to sensitive audio and DDR memory planes. The internal 10-bit ADC monitors each rail, die temperature, and input voltage, allowing host software to validate power integrity and respond to thermal or fault events. The pre-programmed OTP memory and reference BSP dramatically reduce NXP i.MX 8M design-in time.
Typical applications include set-top boxes, smart home audio hubs, industrial HMI panels, and i.MX 8M-based single-board computers. The wide input range and configurable sequencing also suit portable medical imaging terminals and similar A/V-rich embedded platforms where board space and design time are tightly constrained.
When designing with this device, follow the reference design closely for input capacitance, layout of the exposed thermal pad, and SW node routing; the OTP defaults assume specific LPDDR4 voltage and i.MX 8M boot sequencing. Designers should validate thermal performance at full 14-rail load under worst-case ambient to keep junction temperature inside the -40C to +105C operating range.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes from the NXP PF4210 datasheet and field experience, giving engineering teams a faster path to a validated i.MX 8M power tree than wading through 100+ pages of PMIC documentation alone.
Drop-in-Alternativen für MC34PF4210A0ES – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
MC34PF4210A1ES
✅ Drop-In✓ Auf Lager
$5.2 / Stück
Datenblatt ansehen →MC34PF4210A3ES
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MC34PF4210A2ES
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MC34PF4210A0ES Grenzwerte & elektrische Eigenschaften
| Product Type | Power Management IC (PMIC) |
| Topologie | Multi-rail buck + LDO + boost + ADC |
| Number of Output Channels | 14 channels |
| Buck Converters | 4/6 synchronous buck converters |
| LDO Regulators | 7 LDOs |
| Boost Converters | 5 boost outputs |
| ADC | 10-bit integrated ADC for monitoring |
| Configuration Memory | On-chip OTP (one-time programmable), pre-programmed |
| Communication Interface | I2C control |
| Adjustable Current Limiting | Yes, per output |
| Sanftanlauf | Adjustable per channel |
| Dynamic Voltage Scaling (DVS) | Yes |
| Power-On Sequencing | Programmable via OTP and I2C |
| Protection Features | Overcurrent protection, OVP, UVLO, thermal shutdown |
| Betriebstemperaturbereich | -40C to +105C |
| Gehäuse | 56-QFN-EP (8x8 mm) with exposed thermal pad |
| Montageart | Surface Mount |
| Target Processor | NXP i.MX 8M family applications processors |
| RoHS Compliance | Compliant (per NXP product page) |
MC34PF4210A0ES 56-qfn-ep (8x8 mm) with exposed thermal pad Pinbelegungsleitfaden
Pinbelegung für MC34PF4210A0ES (56-qfn-ep (8x8 mm) with exposed thermal pad-Gehäuse). Dieses Leistungsbauteil verfügt über Gate-, Drain- und Source-Anschlüsse. Bei nicht gepolten Gehäusen entnehmen Sie die genaue Ausrichtung von Pin 1 und Footprint-Details dem Herstellerdatenblatt. Typische Anwendungen sind Netzteilentwurf, Motoransteuerung und Lastschaltung.
Keine detaillierten Pinbelegungsdaten verfügbar für MC34PF4210A0ES.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MC34PF4210A0ES ist geeignet für 6 Anwendungs: i.MX 8M Set-Top Box and Streaming Device, Smart Home Audio Hub and Smart Display, Industrial HMI and Panel PCs, Automotive Infotainment and Telematics (non-AEC-Q100 use), Single-Board Computer and Maker Platform, Portable Medical Imaging Terminal.
i.MX 8M Set-Top Box and Streaming Device
The MC34PF4210A0ES is purpose-built for i.MX 8M set-top box designs, where it powers the quad-core Cortex-A53 core, Cortex-M4 real-time core, GPU, and DDR memory from a single 5V input. Its 4/6 buck converters deliver high-current cores (up to ~2.5A per phase per NXP community guidance), while 7 LDOs feed low-noise analog, USB PHY, and PLL rails. The 10-bit ADC continuously monitors each rail so host firmware can throttle performance on thermal stress. Compared to discrete regulators, the PF4210 cuts BOM count by ~20 parts and dramatically simplifies power sequencing, which is critical when the SoC requires specific rail order for LPDDR4 boot.
Empfohlen
Smart Home Audio Hub and Smart Display
In smart home audio hubs and smart displays, the MC34PF4210A0ES supplies the i.MX 8M SoC plus its microphones, Class-D amplifier, and LCD backlight from a single battery or wall adapter. The 5 boost outputs drive LED backlights and speaker-amplifier rails directly, while the 7 LDOs cleanly feed microphone bias and audio codec analog domains. Built-in dynamic voltage scaling (DVS) lets the device lower core voltage during voice standby, extending battery life in always-listening products. The 56-QFN-EP exposed pad enables compact PCB layouts suitable for slim smart speaker enclosures.
Empfohlen
Industrial HMI and Panel PCs
Industrial HMI panels and panel PCs use the MC34PF4210A0ES to consolidate all i.MX 8M processor rails in a single PMIC, reducing PCB area and improving long-term reliability under -40C to +105C operation. The OTP-programmed power-on sequencing allows deterministic boot for safety-critical HMI software, while the integrated 10-bit ADC reports rail voltages and die temperature to the host for diagnostics. The wide input range and overcurrent protection make the PF4210 well suited to industrial 24V backplane systems with downstream point-of-load conversion. Adjustable current limit enables per-port tuning for USB, sensor, and display loads on the panel.
Empfohlen
Automotive Infotainment and Telematics (non-AEC-Q100 use)
Although the MC34PF4210A0ES is not AEC-Q100 qualified, it is widely used in non-safety automotive infotainment prototypes, aftermarket head units, and telematics prototypes where the i.MX 8M drives display, audio, and connectivity subsystems. The 14 rails cover SoC cores, GPU, CAN transceivers, Wi-Fi/Bluetooth modules, and display backlights from a single 12V automotive battery input through upstream regulation. Dynamic voltage scaling supports fuel-saving modes by lowering processor voltage when the vehicle is parked. Designers must still qualify for AEC-Q100 with the NXP automotive-grade equivalent when targeting production safety-critical ECUs.
Empfohlen
Single-Board Computer and Maker Platform
Single-board computers and i.MX 8M maker platforms integrate the MC34PF4210A0ES because it provides a complete, BSP-supported power tree in a single 56-QFN-EP IC. This allows board designers to focus on peripheral layout instead of sequencing logic, and to ship fully Linux-supported images on day one. The NXP reference BSP includes PMIC driver code, regulators, and thermal zones, drastically shortening time-to-prototype. The 10-bit ADC exposes die temperature and rail telemetry via sysfs, enabling developer monitoring and debugging on the developer kit.
Empfohlen
Portable Medical Imaging Terminal
Portable medical imaging terminals powered by i.MX 8M processors benefit from the MC34PF4210A0ES integration, which condenses the entire power tree into one 56-QFN-EP device to leave board area for batteries and analog front ends. The 5 boost outputs can drive small LCD panels and bias supplies, while the 7 LDOs feed precision analog ASICs for ultrasound or vital-sign capture with low noise. Adjustable soft-start prevents inrush current from tripping hospital-grade isolation, and the integrated OTP guarantees a deterministic boot for IEC 62304 software classification. Operating range up to +105C supports sealed enclosure designs used in clinical environments.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MC34PF4210A0ES – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MC34PF4210A1ES | MC34PF4210A3ES | MC34PF4210A2ES |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 56-QFN-EP (8x8 mm) | 56-QFN-EP (8x8 mm) | 56-QFN-EP (8x8 mm) | 56-QFN-EP (8x8 mm) |
| Output Channels | 14 | 14 | 14 | 14 |
| Buck Converters | 4/6 | 4/6 | 4/6 | 4/6 |
| LDOs | 7 | 7 | 7 | 7 |
| Boost Outputs | 5 | 5 | 5 | 5 |
| Integrated ADC | 10-bit | 10-bit | 10-bit | 10-bit |
| OTP Revision | A0 (initial factory defaults) | A1 (updated default voltages) | A3 (latest defaults for newer i.MX 8M) | A2 (intermediate revision) |
| Target Processor | i.MX 8M family | i.MX 8M family | i.MX 8M family | i.MX 8M family |
| Operating Temperature | -40C to +105C | -40C to +105C | -40C to +105C | -40C to +105C |
Wichtigste Unterscheidungsmerkmale
- Tightest factory OTP defaults for i.MX 8M (vs. MC34PF4210A1ES)
- Latest OTP revision support (vs. MC34PF4210A3ES)
- Single-IC 14-rail integration (vs. Discrete buck + LDO array (no equivalent drop-in))
Designhinweise
The 56-QFN-EP exposed thermal pad is the primary heat-dissipation path for the MC34PF4210A0ES. Estimated: at full 14-rail load (assume 4 W total dissipation worst case), with a board thermal resistance of ~25 C/W to a 4-layer 2 oz copper pour, the junction rises roughly 100 C above ambient. Provide at least 1 square inch of continuous copper under the exposed pad, with thermal vias on a 1 mm pitch, to keep Tj within the -40C to +105C operating range.
Place input bulk capacitors within 5 mm of the VIN pins and keep the high-current switching loops (SW node) on the top layer with the smallest possible loop area. Use a 4-layer stack with a dedicated ground plane underneath the device. The exposed thermal pad must be soldered to the board with a 0.3 mm via-array pattern; missing thermal vias increase theta_JA by ~30% and risk thermal-shutdown behavior under load.
Do not assume the OTP defaults match your exact i.MX 8M processor revision - if the defaults are wrong, the regulator may overshoot or undershoot core rails during boot and trigger latch-up. Always load the latest NXP reference BSP and re-run the PF4210 OTP verification flow before locking in volume production. Also note that strap-pin states at first power-on determine the OTP bank selected; pull-ups must match the schematic exactly.
Soft-start timing per channel is adjustable via external capacitor on the SS pins or via I2C register; set the core buck soft-start to ~2 ms to avoid inrush on the upstream supply. Use 22 uF X7R ceramic input capacitors on each high-current buck to minimize ripple; insufficient bulk capacitance will trigger the adjustable current-limit and cause the regulator to hiccup during transients.
Compliance-Informationen
RoHS and lead-free status per NXP product page. Not AEC-Q100 qualified - choose an automotive-grade NXP PMIC for safety-critical ECUs.
