Renesas Electronics

MC68150FN33 - 5V 68-PLCC Bus Interface IC | Renesas

Teilenummer: MC68150FN33 ✗ Abgekündigt
4.5 V Vdss 68-pin PLCC with J-lead termination Package
MOQ: 1 |

MC68150FN33 Übersicht

Renesas Electronics MC68150FN33 is a specialized bus-interface integrated circuit designed for 4.5 V to 5.5 V operation and supplied in a 68-pin plastic leaded chip carrier package measuring 24.21 mm by 24.21 mm. It is listed as an interface IC with J-lead termination and tube packaging, placing it in the broader category of bus interface and data-processing semiconductors. The MC68150FN33 designation identifies a specific operating grade within the MC68150 product family.

A bus-interface IC serves as the electrical and protocol interface between a host processor or peripheral bus and a higher-level computer bus. Such devices may translate signals, arbitrate bus ownership, manage timing, or provide the electrical characteristics required by a legacy computer architecture. Because the MC68150FN33 belongs to the specialized MC68150 family, engineers should consult the family documentation for its exact bus protocol, signal timing, and host-interface behavior before finalizing a new design.

The principal verified characteristics are a 4.5 V minimum supply voltage, a 5.5 V maximum supply voltage, a 68-pin J-lead PLCC package, a 24.21 mm by 24.21 mm body size, and tube packaging. These parameters make the device suitable for legacy 5 V systems that can accommodate the physical footprint and pin arrangement of the MC68150FN33. The wide 1 V supply range also provides conventional 5 V margin when accounting for supply variation.

MC68150FN33 is categorized as a bus interface rather than a general-purpose microcontroller, and its useful operating context is specialized computer and peripheral-interface equipment. Its 5 V supply requirement is consistent with established 68000-family and similar bus-control applications. The J-lead package supports through-hole assembly and may simplify repair or legacy-system maintenance, although the relatively large 68-pin footprint requires careful component placement and adequate connector spacing.

Typical engineering uses include industrial control systems, legacy peripheral controllers, embedded computer equipment, and service or modernization projects that retain a compatible MC68150-based bus architecture. In each case, supply sequencing, signal termination, clocking, and device-enable requirements must be checked against the authoritative device documentation. Modern replacements should also be assessed for protocol, timing, voltage, and footprint compatibility rather than function alone.

For new PCB layouts, place the MC68150FN33 according to the package drawing and preserve the specified bypass-capacitor and interface routing arrangement. Confirm that the surrounding logic uses compatible voltage levels and that no replacement changes signal polarity, direction, or bus timing. For assembled legacy equipment, inspect all socketed contacts and verify that the tube orientation matches the pin-one marking.

This product record combines the confirmed electrical range, package geometry, packaging method, sourcing links, and engineering guidance needed to evaluate the MC68150FN33. It also distinguishes documented facts from parameters that must be confirmed in the authoritative MC68150 datasheet before schematic sign-off, simulation, or production release.

Drop-in-Alternativen für MC68150FN33 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.

Alternativen anfordern

MC68150FN33 Technische Daten

Product Type Bus Interface IC
Device Category Specialized Interface IC
Minimum Supply Voltage 4.5 V
Maximum Supply Voltage 5.5 V
Nominal Supply Voltage 5 V
Schnittstellentyp Bus
Package Type 68-pin PLCC with J-lead termination
Package Body Size 24.21 mm x 24.21 mm
Pin-Anzahl 68 pins
Montageart Surface mount
Packaging Type Tube

MC68150FN33 24.21 mm x 24.21 mm Pinbelegungsleitfaden

Pinbelegung für MC68150FN33 (24.21 mm x 24.21 mm-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für MC68150FN33 im 24.21 mm x 24.21 mm-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für MC68150FN33.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

MC68150FN33 ist geeignet für 6 Anwendungs: Legacy Industrial Control Systems, Embedded Peripheral Controllers, Legacy Computer Interface Equipment, Data Acquisition and Measurement Systems, Printer and Peripheral Controllers, Equipment Maintenance and Obsolescence Planning.

🏭

Legacy Industrial Control Systems

The MC68150FN33 can support a legacy industrial control assembly that retains the specialized MC68150 bus architecture. Its confirmed 4.5 V to 5.5 V supply range aligns with established 5 V control logic, while the 68-pin J-lead PLCC supports serviceable through-hole construction. The device should be placed only where its bus timing, enable sequencing, and signal levels match the existing controller. Before expanding production, engineers should verify clock margin and conditioning requirements from the authoritative family documentation.

🔧

Embedded Peripheral Controllers

The MC68150FN33 is applicable to embedded peripheral-control equipment designed around a compatible MC68150 bus interface and a 5 V logic environment. Its 68-pin PLCC footprint makes it suitable for maintenance boards that retain the original socket or plated land pattern. Integration requires attention to supply tolerance, bus timing, and the exact direction of each interface signal. A firmware or hardware migration should be treated as a redesign unless all electrical and protocol characteristics have been compared explicitly.

🖥️

Legacy Computer Interface Equipment

The MC68150FN33 fits maintenance of legacy computer-interface equipment that expects a specialized bus controller operating at 5 V. The confirmed 4.5 V to 5.5 V supply range provides nominal 5 V margin, while the 24.21 mm by 24.21 mm 68-pin J-lead package allows board-level repair using compatible socket hardware. Technicians should inspect socket oxidation, confirm pin-one orientation, and validate reset or enable sequencing before energizing the assembly. Replace only with a part whose protocol and pinout are demonstrably equivalent.

📺

Data Acquisition and Measurement Systems

The MC68150FN33 may be used in a legacy data-acquisition system where the measurement architecture already includes a compatible MC68150 interface. Its nominal 5 V supply range suits older analog and digital control sections, and the J-lead package simplifies replacement on through-hole measurement boards. The engineer should confirm whether the bus carries timing-sensitive acquisition commands and whether bypass capacitance can be placed close to the device. Any conversion to a modern interface should include complete timing, logic-level, and footprint validation.

🖨️

Printer and Peripheral Controllers

The MC68150FN33 is relevant to older printer, scanner, or peripheral-controller boards designed around the MC68150 bus and 5 V supply. Its 68-pin PLCC package supports board-level replacement without changing a socketed legacy layout. Installation requires verification of the controller's bus timing, handshake polarity, and available supply headroom at the device pins. Designers should preserve the documented decoupling arrangement and avoid substituting a similar interface IC unless its pinout and protocol are confirmed equivalent.

🔩

Equipment Maintenance and Obsolescence Planning

The MC68150FN33 supports maintenance and obsolescence planning for installed equipment that cannot yet be migrated. Its 4.5 V to 5.5 V operating range and 68-pin J-lead PLCC package define the electrical and mechanical constraints for a replacement decision. Procurement teams should obtain current quantity, condition, and traceability through the Request a Quote form, while engineers should maintain a controlled equivalent only after comparing pinout, protocol, timing, and lifecycle expectations. This approach reduces risk in long-lived industrial installations.

Zusammenfassung der empfohlenen Produkte

MC68150FN33 Renesas Electronics Verwendet in: Legacy Industrial Control Systems, Embedded Peripheral Controllers, Legacy Computer Interface Equipment, Data Acquisition and Measurement Systems, Printer and Peripheral Controllers, Equipment Maintenance and Obsolescence Planning MC68150 MC68150 family identifier Verwendet in: Legacy Industrial Control Systems, Embedded Peripheral Controllers, Legacy Computer Interface Equipment, Data Acquisition and Measurement Systems, Printer and Peripheral Controllers, Equipment Maintenance and Obsolescence Planning
What is the MC68150FN33?
The MC68150FN33 is a specialized Renesas Electronics bus-interface IC designed to operate from a 4.5 V to 5.5 V supply. The manufacturer listing identifies it as an interface device, while the MC68150 family is associated with specialized computer-bus interfacing. Its 68-pin J-lead PLCC package and tube packing make it primarily relevant to legacy embedded and industrial systems. Confirm the exact protocol, timing, and signal assignments in the authoritative MC68150 documentation before using it in a new schematic.
What is the operating voltage of MC68150FN33?
The MC68150FN33 operates from 4.5 V to 5.5 V, making it a nominal 5 V interface device. According to the MC68150FN33 component specification, this range provides 0.5 V of headroom below and above a nominal 5 V rail. Power-supply design must also satisfy the device's input thresholds, sequencing requirements, and bypass-capacitor recommendations. Use the manufacturer datasheet for the complete absolute maximum and recommended operating conditions.
What package does MC68150FN33 use?
The MC68150FN33 uses a 68-pin PLCC package with J-lead termination and a body measuring 24.21 mm by 24.21 mm. The component listing also identifies tube packaging for the offered configuration. Because no matching PLCC-68 diagram exists in the package library, the product page uses the default package graphic rather than presenting an unverified pin map. The manufacturer package drawing must be used for land patterns, pin-one orientation, and socket compatibility.
Where can I download the MC68150FN33 datasheet PDF?
The MC68150FN33 product listing is available through the Renesas Electronics product entry on DigiKey, while the MC68150 family documentation should be obtained from Renesas Electronics. Start with the product link on this page and use the MC68150 family name to locate the manufacturer PDF. Check the document revision before adopting its timing diagrams, electrical limits, or pin assignments, particularly when maintaining equipment designed around an earlier revision.
Where can I find the MC68150FN33 pinout?
The authoritative MC68150FN33 pinout is the 68-pin PLCC pin-description table in the manufacturer documentation for the MC68150 family. The confirmed package information is a 68-pin J-lead PLCC measuring 24.21 mm by 24.21 mm, but individual signal names and active levels are not published in the product listing. Use the manufacturer package drawing to identify pin one and avoid inferring the pinout from similarly named interface devices.
Is MC68150FN33 suitable for a 5 V embedded system?
The MC68150FN33 is suitable for a 5 V embedded system when its bus protocol, timing, signal levels, and pin functions match the surrounding controller. Its documented 4.5 V to 5.5 V supply range supports nominal 5 V operation. Legacy industrial, peripheral-control, and embedded-computer systems are plausible applications, subject to confirmation of clock frequency, enable sequencing, and interrupt behavior in the MC68150 documentation.
What can replace the MC68150FN33?
A true replacement for the MC68150FN33 must preserve its 68-pin PLCC footprint, 4.5 V to 5.5 V supply range, bus protocol, electrical timing, and signal-level behavior. The available cross-reference results do not identify a candidate that can be verified as pin-to-pin and functionally equivalent. Use the Request a Quote form on this page for sourcing support, and require a manufacturer comparison before treating any functional equivalent as a drop-in replacement.
Is MC68150FN33 the same as the MC68150?
The MC68150FN33 is a specific ordering designation within the MC68150 family, while MC68150 is the broader family identifier. The MC68150FN33 listing specifies the 68-pin J-lead PLCC, 4.5 V to 5.5 V supply, and tube packaging. The suffix can encode device-specific characteristics, so the MC68150 family name alone is not sufficient to confirm interchangeability. Verify the complete ordering code and package suffix before substitution.
What are the key specifications of MC68150FN33 that engineers should know?
The key confirmed MC68150FN33 specifications are its specialized bus-interface function, 4.5 V to 5.5 V operating range, 68-pin J-lead PLCC package, 24.21 mm by 24.21 mm body size, and tube packaging. The component listing classifies it as an interface IC rather than a general-purpose microcontroller. Clock rate, signal directions, protocol details, thermal limits, and individual pin functions require confirmation from the authoritative MC68150 manufacturer documentation.
Where can I buy MC68150FN33?
The MC68150FN33 can be requested through the Request a Quote form on this page, which supports inquiries for legacy and limited-availability electronic components. The part is listed as a 68-pin PLCC interface IC from Renesas Electronics, with tube packaging identified in the product records. Request the current stock position, minimum order quantity, condition, and lead time through that form before committing the component to a production schedule.
What is the price of MC68150FN33?
The current commercial terms for the MC68150FN33 are handled through the Request a Quote form on this page. The component is a specialized legacy interface IC, so availability, condition, and order quantity can affect its commercial offer. The form is the appropriate route for obtaining a current unit price, volume breaks, and lead time without relying on an outdated catalog figure that may not reflect available inventory.
What is the lead time for MC68150FN33?
The current lead time for the MC68150FN33 should be confirmed through the Request a Quote form on this page. Because this is a specialized interface IC associated with legacy computer equipment, production planning may depend on remaining factory inventory, package configuration, and replenishment status. Include the required quantity, tube-packaging preference, and target assembly date in the request so the supplier can provide a meaningful schedule.
Is MC68150FN33 in stock?
Stock status for MC68150FN33 should be checked through the Request a Quote form on this page. The product listing identifies the 68-pin PLCC configuration and tube packaging, but a live searchable quantity is not established by the technical product record. For maintenance and small-build requirements, request the available quantity, component condition, date code, and traceability information before releasing a purchase order.
MC68150FN33 versus a modern bus-interface controller: which is better?
The MC68150FN33 is preferable when an existing system requires its original MC68150 protocol, pin arrangement, and legacy interface behavior. A modern controller is usually preferable for a new design because it offers modern integration, tooling, and potentially broader supply. The MC68150FN33 remains useful for repairing or maintaining 5 V embedded systems, but a modern device should not be treated as a drop-in replacement unless its footprint, timing, levels, and protocol have been verified.
What should I check before using MC68150FN33 in a legacy system?
Check the supply voltage, clock limits, bus protocol, signal directions, enable sequencing, and timing margins before using the MC68150FN33 in a legacy system. The confirmed operating range is 4.5 V to 5.5 V, and the device uses a 68-pin J-lead PLCC. Also verify package orientation, socket condition, trace compatibility, and the required bypass components. These checks prevent a functionally similar part from being treated as an unqualified drop-in substitute.

Technische Referenzdaten für MC68150FN33 – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the MC68150FN33 when maintaining a system that specifically uses the MC68150 bus interface and retains a 68-pin J-lead PLCC layout. It is a sensible exact-part option for legacy industrial, embedded-computer, and peripheral-control equipment operating on a nominal 5 V rail. Compatibility cannot be inferred from the package alone: the bus protocol, clock rate, pin functions, timing, and signal polarity must match the original system. A modern controller is preferable for a new design when lower supply voltage, greater integration, or newer lifecycle support is desired, but it should be treated as a redesign unless its footprint and electrical behavior are proven equivalent. For obsolescence planning, obtain current sourcing terms through the Request a Quote form and qualify any alternative against the authoritative MC68150 documentation before changing the BOM.

Vergleich mit Alternativen

Parameter Dieses Produkt
Manufacturer Renesas Electronics
Package 68-pin PLCC with J-lead termination
Body Size 24.21 mm x 24.21 mm
Supply Voltage Range 4.5 V to 5.5 V
Interface Category Bus
Device Classification Specialized Interface IC
Packaging Tube
Pin Count 68 pins
Mounting Style Surface mount

Wichtigste Unterscheidungsmerkmale

  • Exact legacy bus-interface ordering code (vs. Generic 68-pin PLCC interface IC)
  • Defined 5 V operating range (vs. Modern 3.3 V bus-interface controller)
  • Serviceable 68-pin J-lead PLCC construction (vs. Leadless surface-mount interface controller)
  • Tube-packaged legacy procurement format (vs. Reel-packed modern interface IC)

Designhinweise

Use the manufacturer PLCC drawing to establish the land pattern, pin-one location, and board clearances. The package body is 24.21 mm by 24.21 mm and has 68 J-lead terminals, so do not infer geometry from a generic PLCC footprint. Preserve compatible socket positions during maintenance, and check plated-hole tolerances, solderability, and component orientation after board rework. Because the available package graphic is generic, the manufacturer drawing must govern the layout.

Design the local supply around the confirmed 4.5 V to 5.5 V operating range and verify the device pins receive the required voltage under the worst case. Place the recommended bypass capacitors close to the supply and ground pins, with short, low-inductance traces. Confirm power-up and enable sequencing against the MC68150 documentation, particularly on legacy boards where multiple interface devices can contend for the bus during initialization.

Do not treat another 68-pin PLCC interface IC as a substitute based on package similarity. Confirm the exact pin assignments, bus protocol, clock limit, signal polarity, and electrical timing against the MC68150 documentation. For maintenance, also inspect socket contacts for oxidation and bent leads before concluding that the IC is defective. A request for a functional equivalent must include the board's clock rate, bus topology, and supply conditions so that the proposed part can be screened properly.

Route clock and bus signals according to the manufacturer's topology and keep the interface path away from noisy switching nodes when the board is being revised. Maintain continuous ground references around the PLCC and place nearby decoupling where it can service the device without a long supply loop. Legacy boards should be inspected for damaged traces, socket solder bridges, and contamination because these failures can resemble an IC-level timing or bus fault.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The product record references lead-free status and tube packaging but does not provide a definitive compliance classification. Compliance and qualification attributes require confirmation from Renesas Electronics or the authoritative product documentation.

Daten verifiziert am: 2026-11-15 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

MC68150FN33 datasheet MC68150FN33 pinout MC68150FN33 datasheet pdf MC68150FN33 equivalent MC68150FN33 replacement MC68150FN33 cross reference MC68150FN33 price MC68150FN33 stock Renesas MC68150FN33 MC68150FN33 68 PLCC MC68150FN33 5V bus interface MC68150FN33 legacy computer interface

Verwandte Bauteile & Begriffe

Renesas Electronics MC68150FN33 MC68150 Motorola Semiconductor Freescale Semiconductor onsemi Bus Interface IC Interface IC Computer Bus Interface Specialized Interface IC 5 V Logic 4.5 V Minimum Supply Voltage 5.5 V Maximum Supply Voltage 68-pin PLCC J-lead Package PLCC Surface Mount Tube Packaging Industrial Control Systems Legacy Peripheral Controllers Data Acquisition Systems Bus Protocol Signal Timing Lead-Free Status Obsolescence Planning
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen