MC68150FN33 - 5V 68-PLCC Bus Interface IC | Renesas
부품 번호: MC68150FN33 ✗ 단종MC68150FN33 개요
A bus-interface IC serves as the electrical and protocol interface between a host processor or peripheral bus and a higher-level computer bus. Such devices may translate signals, arbitrate bus ownership, manage timing, or provide the electrical characteristics required by a legacy computer architecture. Because the MC68150FN33 belongs to the specialized MC68150 family, engineers should consult the family documentation for its exact bus protocol, signal timing, and host-interface behavior before finalizing a new design.
The principal verified characteristics are a 4.5 V minimum supply voltage, a 5.5 V maximum supply voltage, a 68-pin J-lead PLCC package, a 24.21 mm by 24.21 mm body size, and tube packaging. These parameters make the device suitable for legacy 5 V systems that can accommodate the physical footprint and pin arrangement of the MC68150FN33. The wide 1 V supply range also provides conventional 5 V margin when accounting for supply variation.
MC68150FN33 is categorized as a bus interface rather than a general-purpose microcontroller, and its useful operating context is specialized computer and peripheral-interface equipment. Its 5 V supply requirement is consistent with established 68000-family and similar bus-control applications. The J-lead package supports through-hole assembly and may simplify repair or legacy-system maintenance, although the relatively large 68-pin footprint requires careful component placement and adequate connector spacing.
Typical engineering uses include industrial control systems, legacy peripheral controllers, embedded computer equipment, and service or modernization projects that retain a compatible MC68150-based bus architecture. In each case, supply sequencing, signal termination, clocking, and device-enable requirements must be checked against the authoritative device documentation. Modern replacements should also be assessed for protocol, timing, voltage, and footprint compatibility rather than function alone.
For new PCB layouts, place the MC68150FN33 according to the package drawing and preserve the specified bypass-capacitor and interface routing arrangement. Confirm that the surrounding logic uses compatible voltage levels and that no replacement changes signal polarity, direction, or bus timing. For assembled legacy equipment, inspect all socketed contacts and verify that the tube orientation matches the pin-one marking.
This product record combines the confirmed electrical range, package geometry, packaging method, sourcing links, and engineering guidance needed to evaluate the MC68150FN33. It also distinguishes documented facts from parameters that must be confirmed in the authoritative MC68150 datasheet before schematic sign-off, simulation, or production release.
드롭인 대체품: MC68150FN33 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청MC68150FN33 사양
| Product Type | Bus Interface IC |
| Device Category | Specialized Interface IC |
| Minimum Supply Voltage | 4.5 V |
| Maximum Supply Voltage | 5.5 V |
| Nominal Supply Voltage | 5 V |
| 인터페이스 유형 | Bus |
| Package Type | 68-pin PLCC with J-lead termination |
| Package Body Size | 24.21 mm x 24.21 mm |
| 핀 수 | 68 pins |
| 실장 유형 | Surface mount |
| Packaging Type | Tube |
MC68150FN33 24.21 mm x 24.21 mm 핀 구성 가이드
MC68150FN33(24.21 mm x 24.21 mm 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: MC68150FN33.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
MC68150FN33 적합 용도: 6 애플리케이션s: Legacy Industrial Control Systems, Embedded Peripheral Controllers, Legacy Computer Interface Equipment, Data Acquisition and Measurement Systems, Printer and Peripheral Controllers, Equipment Maintenance and Obsolescence Planning.
Legacy Industrial Control Systems
The MC68150FN33 can support a legacy industrial control assembly that retains the specialized MC68150 bus architecture. Its confirmed 4.5 V to 5.5 V supply range aligns with established 5 V control logic, while the 68-pin J-lead PLCC supports serviceable through-hole construction. The device should be placed only where its bus timing, enable sequencing, and signal levels match the existing controller. Before expanding production, engineers should verify clock margin and conditioning requirements from the authoritative family documentation.
추천
Embedded Peripheral Controllers
The MC68150FN33 is applicable to embedded peripheral-control equipment designed around a compatible MC68150 bus interface and a 5 V logic environment. Its 68-pin PLCC footprint makes it suitable for maintenance boards that retain the original socket or plated land pattern. Integration requires attention to supply tolerance, bus timing, and the exact direction of each interface signal. A firmware or hardware migration should be treated as a redesign unless all electrical and protocol characteristics have been compared explicitly.
추천
Legacy Computer Interface Equipment
The MC68150FN33 fits maintenance of legacy computer-interface equipment that expects a specialized bus controller operating at 5 V. The confirmed 4.5 V to 5.5 V supply range provides nominal 5 V margin, while the 24.21 mm by 24.21 mm 68-pin J-lead package allows board-level repair using compatible socket hardware. Technicians should inspect socket oxidation, confirm pin-one orientation, and validate reset or enable sequencing before energizing the assembly. Replace only with a part whose protocol and pinout are demonstrably equivalent.
추천
Data Acquisition and Measurement Systems
The MC68150FN33 may be used in a legacy data-acquisition system where the measurement architecture already includes a compatible MC68150 interface. Its nominal 5 V supply range suits older analog and digital control sections, and the J-lead package simplifies replacement on through-hole measurement boards. The engineer should confirm whether the bus carries timing-sensitive acquisition commands and whether bypass capacitance can be placed close to the device. Any conversion to a modern interface should include complete timing, logic-level, and footprint validation.
추천
Printer and Peripheral Controllers
The MC68150FN33 is relevant to older printer, scanner, or peripheral-controller boards designed around the MC68150 bus and 5 V supply. Its 68-pin PLCC package supports board-level replacement without changing a socketed legacy layout. Installation requires verification of the controller's bus timing, handshake polarity, and available supply headroom at the device pins. Designers should preserve the documented decoupling arrangement and avoid substituting a similar interface IC unless its pinout and protocol are confirmed equivalent.
추천
Equipment Maintenance and Obsolescence Planning
The MC68150FN33 supports maintenance and obsolescence planning for installed equipment that cannot yet be migrated. Its 4.5 V to 5.5 V operating range and 68-pin J-lead PLCC package define the electrical and mechanical constraints for a replacement decision. Procurement teams should obtain current quantity, condition, and traceability through the Request a Quote form, while engineers should maintain a controlled equivalent only after comparing pinout, protocol, timing, and lifecycle expectations. This approach reduces risk in long-lived industrial installations.
추천
추천 제품 요약
엔지니어링 참조 데이터: MC68150FN33 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Manufacturer | Renesas Electronics |
| Package | 68-pin PLCC with J-lead termination |
| Body Size | 24.21 mm x 24.21 mm |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Interface Category | Bus |
| Device Classification | Specialized Interface IC |
| Packaging | Tube |
| Pin Count | 68 pins |
| Mounting Style | Surface mount |
주요 차별점
- Exact legacy bus-interface ordering code (vs Generic 68-pin PLCC interface IC)
- Defined 5 V operating range (vs Modern 3.3 V bus-interface controller)
- Serviceable 68-pin J-lead PLCC construction (vs Leadless surface-mount interface controller)
- Tube-packaged legacy procurement format (vs Reel-packed modern interface IC)
설계 노트
Use the manufacturer PLCC drawing to establish the land pattern, pin-one location, and board clearances. The package body is 24.21 mm by 24.21 mm and has 68 J-lead terminals, so do not infer geometry from a generic PLCC footprint. Preserve compatible socket positions during maintenance, and check plated-hole tolerances, solderability, and component orientation after board rework. Because the available package graphic is generic, the manufacturer drawing must govern the layout.
Design the local supply around the confirmed 4.5 V to 5.5 V operating range and verify the device pins receive the required voltage under the worst case. Place the recommended bypass capacitors close to the supply and ground pins, with short, low-inductance traces. Confirm power-up and enable sequencing against the MC68150 documentation, particularly on legacy boards where multiple interface devices can contend for the bus during initialization.
Do not treat another 68-pin PLCC interface IC as a substitute based on package similarity. Confirm the exact pin assignments, bus protocol, clock limit, signal polarity, and electrical timing against the MC68150 documentation. For maintenance, also inspect socket contacts for oxidation and bent leads before concluding that the IC is defective. A request for a functional equivalent must include the board's clock rate, bus topology, and supply conditions so that the proposed part can be screened properly.
Route clock and bus signals according to the manufacturer's topology and keep the interface path away from noisy switching nodes when the board is being revised. Maintain continuous ground references around the PLCC and place nearby decoupling where it can service the device without a long supply loop. Legacy boards should be inspected for damaged traces, socket solder bridges, and contamination because these failures can resemble an IC-level timing or bus fault.
규정 준수 정보
The product record references lead-free status and tube packaging but does not provide a definitive compliance classification. Compliance and qualification attributes require confirmation from Renesas Electronics or the authoritative product documentation.