MC9S08AC96CL - 8-Bit 40MHz 96KB Flash MCU | NXP
Teilenummer: MC9S08AC96CL ✗ Abgekündigt| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
MC9S08AC96CL Übersicht
A microcontroller is a programmable semiconductor that integrates a CPU core, memory, peripherals, and input/output interfaces on one device. The HCS08 S08 family belongs to the 8-bit MCU hierarchy and is commonly used for cost-sensitive control, monitoring, communication, and actuator-control designs. Its peripherals let a product perform useful tasks without relying on a separate processor for basic real-time control.
The verified distributor listing identifies the MC9S08AC96CL as an HCS08 S08 microcontroller operating up to 40 MHz with 96 KB of flash memory organized as 96K x 8. The NXP listing for the closely identified MC9S08AC96CLKE additionally states that this family variant provides 4 KB of RAM, SCI, SPI, IIC, and integrated CAN support for automotive applications. These interfaces make the device applicable to distributed control systems that need both serial connectivity and CAN communications.
The 80-LQFP package provides a higher pin count than small-outline packages and offers more exposed connection options for peripheral signals, power, debugging, and communications. Its 14 mm by 14 mm body dimensions should be considered during PCB footprint selection, assembly planning, and thermal assessment. Because the supplied verified data does not include the complete electrical limits, pin-level assignments, or memory map, those details must be confirmed against the manufacturer datasheet before a new design is released.
Typical application directions include automotive body and chassis electronics, CAN-connected industrial controllers, communication hubs, data-acquisition equipment, and general embedded automation. The 40 MHz clock supports timely execution of control logic, while the 96 KB flash capacity provides room for firmware and application code. The available SCI, SPI, IIC, and CAN functions support both point-to-point and bus-oriented peripherals when those details are confirmed for the exact ordering option.
Designers should verify the exact package pinout, voltage limits, clock configuration, reset requirements, and peripheral multiplexing in the manufacturer datasheet before layout or firmware deployment. For a replacement decision, do not rely only on the base MC9S08AC96 designation: the CL suffix, package, temperature range, qualification status, and supported peripheral set must all match. This page combines distributor specifications, datasheet references, sourcing links, and practical design guidance to support that verification process.
Drop-in-Alternativen für MC9S08AC96CL – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.
Alternativen anfordernMC9S08AC96CL Grenzwerte & elektrische Eigenschaften
| Device Type | 8-bit HCS08 S08 microcontroller |
| Maximale Taktfrequenz | 40 MHz |
| Flash Memory | 96 KB (96K x 8) |
| RAM | 4 KB |
| Gehäuse | 80-LQFP (14 x 14 mm) |
| Lead Count | 80 leads |
| SCI Interface | Supported |
| SPI Interface | Supported |
| IIC Interface | Supported |
| CAN Support | Integrated CAN support |
| Automotive Application Support | Automotive applications |
| Core Architecture | 8-bit |
| Montageart | Surface mount |
MC9S08AC96CL 80-lqfp (14 x 14 mm) Pinbelegungsleitfaden
Pinbelegung für MC9S08AC96CL (80-lqfp (14 x 14 mm)-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für MC9S08AC96CL.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MC9S08AC96CL ist geeignet für 6 Anwendungs: Automotive Body-Control Module, CAN-Connected Industrial Controller, Automotive Sensor Interface Hub, Communication Gateway, Data-Acquisition and Condition-Monitoring Unit, General Embedded Automation Controller.
Automotive Body-Control Module
The MC9S08AC96CL fits an automotive body-control module that combines logic for switches, lamps, locks, sensors, and actuators within a vehicle network. Its verified 8-bit S08 architecture and 40 MHz maximum clock provide control-processing capability, while 96 KB of flash offers room for application firmware. The related NXP product information identifies automotive applications and integrated CAN support, which is useful when the module must exchange messages with other vehicle systems. The exact CL suffix must still be checked for voltage, temperature, qualification, and pin compatibility before production use.
Empfohlen
CAN-Connected Industrial Controller
The MC9S08AC96CL is appropriate for a small industrial controller that monitors inputs and drives outputs while communicating over a CAN network. The verified device information identifies integrated CAN support, along with SCI, SPI, and IIC, allowing the controller to use multiple serial peripheral types in one design. Its 40 MHz maximum clock and 96 KB of flash support embedded application logic, and the 80-LQFP package exposes more connections than a very small package. In practice, the controller also needs a CAN transceiver, protection components, and exact pin and electrical validation.
Empfohlen
Automotive Sensor Interface Hub
The MC9S08AC96CL can serve as the control hub between vehicle sensors and a communication network when the design requires fast serial conversion and deterministic control. The verified 4 KB RAM and 96 KB flash figures provide a defined memory budget for buffering and firmware, while SCI, SPI, and IIC can connect sensors or external devices using different serial formats. The 80-LQFP package offers substantial pin access for power, communications, and I/O. The engineer must confirm the exact peripheral multiplexing and signal-level requirements in the datasheet, especially for production automotive environments.
Empfohlen
Communication Gateway
The MC9S08AC96CL is suitable for a compact communication gateway that translates data between local serial peripherals and a higher-level embedded control system. Its verified SCI, SPI, and IIC capabilities support different device connections, while the 40 MHz maximum clock and 96 KB flash allocation allow protocol handling and application logic to share one controller. The 80-LQFP package is useful when the gateway needs numerous I/O and communication pins. Final design work should verify baud-rate support, peripheral addressing, interrupt behavior, and electrical limits from the exact datasheet.
Empfohlen
Data-Acquisition and Condition-Monitoring Unit
The MC9S08AC96CL can support a condition-monitoring unit that samples external sensors, evaluates thresholds, records operating states, and reports results over a serial link. Its 8-bit S08 core is appropriate for embedded supervisory logic, and the verified 96 KB flash and 4 KB RAM figures provide a defined starting point for firmware and working data. SCI, SPI, or IIC can connect sensors depending on their interface requirements, while CAN can provide vehicle or industrial-network reporting where applicable. ADC channels, timers, interrupt priorities, and sensor timing are not specified in the supplied data and require datasheet confirmation.
Empfohlen
General Embedded Automation Controller
The MC9S08AC96CL can be used in a general embedded automation controller when a product needs local logic, serial connectivity, and a moderate amount of firmware storage. The verified 40 MHz maximum clock supports responsive control tasks, and the 96 KB flash capacity is larger than the memory footprint of many simple 8-bit controllers. The 80-LQFP package provides a practical choice for boards requiring numerous I/O connections or communication signals. Before selecting it for an industrial product, verify supply voltage, temperature range, watchdog and timer resources, reset behavior, and whether the exact suffix has the required production status.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MC9S08AC96CL – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt |
|---|---|
| Device Type | 8-bit HCS08 S08 microcontroller |
| Maximum Clock Frequency | 40 MHz |
| Flash Memory | 96 KB (96K x 8) |
| RAM | 4 KB |
| Package | 80-LQFP (14 x 14 mm) |
| SCI | Supported |
| SPI | Supported |
| IIC | Supported |
| CAN Support | Integrated CAN support |
| Automotive Application | Automotive applications |
Wichtigste Unterscheidungsmerkmale
- Documented communication breadth (vs. Generic S08-family alternatives without verified interface details)
- Memory configuration (vs. Smaller-memory 8-bit controllers)
- Control performance (vs. Lower-clock general-purpose 8-bit controllers)
- Package connectivity (vs. Small-package MCUs with fewer external leads)
Designhinweise
Verify the exact supply-voltage limits, decoupling requirements, and power-sequencing constraints in the manufacturer datasheet before connecting the 80-LQFP device. Do not infer safe voltage from the 40 MHz clock specification or the related CLKE listing. Place required input and output capacitors close to their designated pins, keep high-current return paths short, and confirm ground-pin assignments against the exact CL package drawing.
The verified package is an 80-LQFP measuring 14 mm by 14 mm. Confirm land pattern, pin-one orientation, pad dimensions, and exposed thermal requirements from the manufacturer package drawing rather than relying on a generic LQFP footprint. Preserve routing clearance for clock, reset, and communication signals, and use the package's complete pin assignment to avoid conflicts between alternate peripheral functions.
For CAN, SCI, SPI, or IIC connections, route signals away from noisy switching nodes and provide the external transceiver or level-shifting circuitry required by the system. Confirm signal levels, termination, pull-up or pull-down requirements, and alternate-function multiplexing in the exact datasheet. Firmware configuration must be treated as part of interface compatibility because changing pin functions can alter the effective pinout without changing the package.
Do not treat MC9S08AC96CL and MC9S08AC96CLKE as automatically interchangeable merely because both appear in 8-bit, 40 MHz, 96 KB-flash listings. Compare suffix-specific temperature, qualification, voltage, marking, and lifecycle information. Also do not assume that a same-package microcontroller is pin-compatible without checking every power, ground, reset, clock, debug, and peripheral pin.
Compliance-Informationen
The verified distributor search includes wording associated with RoHS compliance, but it does not provide a complete manufacturer compliance declaration. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status therefore remain unknown.
