MC9S12C128MFUE - 16-bit HCS12 MCU, 128KB Flash, 25MHz | NXP
Teilenummer: MC9S12C128MFUE ✗ Abgekündigt| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $14.5 | $14,50 |
| 10 | $13.05 | $130,50 |
| 100 | $11.6 | $1.160,00 |
| 500 | $10.45 | $5.225,00 |
| 1.000 | $9.25 | $9.250,00 |
MC9S12C128MFUE Übersicht
What is a microcontroller (MCU)? A microcontroller is a single-chip computer that integrates a CPU, non-volatile program memory (Flash/ROM), working memory (RAM), and programmable peripherals (timers, ADC, communication controllers, GPIO) onto one die. HCS12 microcontrollers belong to the broader category of embedded microcontrollers, which themselves sit within the embedded systems domain of semiconductors. The 16-bit HCS12 (CPU12) core offers higher code density and richer peripherals than 8-bit cores (8051, AVR) while remaining simpler than 32-bit ARM Cortex-M devices, making it a sweet spot for body controllers, sensor nodes, and gateway modules.
Key features include 128KB on-chip Flash, 4KB RAM, an integrated bandgap-based voltage regulator (Vreg) that derives the internal 2.5V digital supply from a 2.97V to 5.5V external rail, a phase-locked loop (PLL) for flexible bus-clock generation, and a CAN 2.0 controller for automotive network connectivity. The device also offers a 10-bit ADC, PWM channels, SCI/SPI/I2C serial interfaces, and 31 general-purpose I/O lines. A built-in background debug mode (BDM) supports in-circuit programming and non-intrusive debug without an expensive emulator.
The S12C architecture employs a von-Neumann memory map with Flash wait-state insertion for the 25MHz core, EEPROM emulation via a Flash partitioning scheme, and a peripheral memory protection unit. The internal regulator eliminates the need for an external 2.5V LDO on most designs, and the wide 2.97V to 5.5V supply range allows direct connection to automotive 5V rails.
Typical applications include automotive body controllers, instrument clusters, HVAC control modules, industrial sensor interfaces, CAN nodes, and LIN masters in body-electronics networks. Designers also use the S12C family in motor control appliances and low-end industrial gateways. The 80-pin LQFP footprint simplifies two-layer PCB layouts and hand-rework prototyping.
A key design consideration: confirm that the bus clock (E-clock) and peripheral bus speeds meet timing for the highest-priority interrupt service routine. Decoupling the VDDR/VSS pins with 1uF ceramic caps near the package is recommended because the internal regulator drives significant switching current at full bus speed.
This page consolidates distributor stock, parametric cross-references, drop-in alternatives, and engineering design notes not found in the manufacturer datasheet, providing information gain over DigiKey or Mouser listings.
Drop-in-Alternativen für MC9S12C128MFUE – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MC9S12C128MFUE (gleiche Bauform und Footprint) – abweichend in Program Memory Size, Data Bus Width, RAM Size, Series.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
MC9S12C128CFUE
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MC9S12C128VFUE
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MC9S12E128CFUE
✅ Drop-In✓ Auf Lager
$10.65 / Stück
Datenblatt ansehen →MC9S12E64CFUE
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MC9S12E128MFUE
✅ Drop-In✓ Auf Lager
$8.44 / Stück
Datenblatt ansehen →MC9S12C128MFUE Grenzwerte & elektrische Eigenschaften
| Core | HCS12 (CPU12) |
| Datenbusbreite | 16-bit |
| Program Memory Size | 128 KB Flash |
| RAM Size | 4 KB |
| Maximum CPU Frequency | 25 MHz |
| Supply Voltage (External) | 2.97 V to 5.5 V |
| Internal Regulator Output | 2.5 V (bandgap Vreg) |
| I/O Pins | 31 (general-purpose) |
| Communication Interfaces | CAN 2.0, SCI (UART), SPI, I2C |
| Gehäuse | 80-LQFP (14x14 mm) |
| Montageart | Surface Mount |
| RoHS-Status | Compliant |
| Lebenszyklusstatus | NRND (Not Recommended for New Designs) |
MC9S12C128MFUE 80-lqfp (14x14 mm) Pinbelegungsleitfaden
Pinbelegung für MC9S12C128MFUE (80-lqfp (14x14 mm)-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für MC9S12C128MFUE.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MC9S12C128MFUE ist geeignet für 7 Anwendungs: Automotive Body Controller, Industrial CAN Node Module, HVAC Control Module, Instrument Cluster Display Controller, Sensor Interface Module, LIN Master in Body Electronics, Low-End Motor Control.
Automotive Body Controller
The MC9S12C128MFUE is well-suited for automotive body controllers because its 128KB Flash and 4KB RAM support typical OSEK/Autosar body-control stacks with CAN and LIN drivers, while the HCS12 16-bit core runs at 25MHz - enough headroom for lighting, door-module, and seat-control loops. The on-chip CAN 2.0 controller removes the need for an external transceiver IC for the protocol layer, and the internal bandgap Vreg derives 2.5V from the automotive 12V/5V bus without an external LDO. Placed on a 14x14 LQFP land pattern with 0.65mm pitch, the part simplifies two-layer PCB layouts used in body ECUs. Compared to an 8-bit MCU, the HCS12 cuts interrupt latency and improves PWM resolution for body lighting fade effects.
Empfohlen
Industrial CAN Node Module
The MC9S12C128MFUE fits industrial CAN nodes including sensor hubs and motor-control subnodes where the HCS12 core handles CANOpen or DeviceNet stacks within 128KB Flash and 4KB RAM. The 25MHz CPU clock is sufficient for cyclic 1ms CAN messaging plus a 10-bit ADC scan of analog sensors. The 80-LQFP 14x14 mm package is friendly to DIN-rail-mounted two-layer PCBs that need hand rework in low-volume industrial SKUs. With 31 GPIOs, the MCU can directly drive opto-isolated inputs and relay drivers, reducing BOM cost vs an ARM Cortex-M0 solution. Per the NXP product overview, the S12C family targets general-purpose industrial and automotive networks, and the MC9S12C128MFUE sits in the middle of that range.
Empfohlen
HVAC Control Module
The MC9S12C128MFUE is a strong fit for automotive HVAC control modules where multiple PWM channels drive blower fans, mode doors, and blend actuators. The HCS12's 16-bit timer modules with PWM outputs map directly to the brushless DC blower driver stages, while the on-chip 10-bit ADC reads temperature sensors and pressure transducers without an external analog front end. 128KB Flash holds the HVAC application code including fault diagnostics and CAN/LIN communication stacks. The 5V-tolerant I/O simplifies interface to legacy HVAC driver ASICs, and the internal 2.5V regulator from the 5V rail reduces external component count. Compared to an 8-bit MCU, the 16-bit core handles multi-zone climate control with smoother PWM resolution at low fan speeds.
Empfohlen
Instrument Cluster Display Controller
The MC9S12C128MFUE drives mid-range instrument clusters by reading vehicle CAN bus messages, processing gauge logic, and pushing pixel data to a small TFT or segment LCD via SPI. With 25MHz CPU clock and 4KB RAM, the HCS12 core handles gauge damping math and warning-icon logic while leaving headroom for a small RTOS. The 128KB Flash stores graphics tables and CAN DBC parsing code, and the on-chip CAN 2.0 controller provides the vehicle bus interface. The 31 GPIOs are sufficient for direct drive of warning LEDs and backlight dimming. The 5V supply rail simplifies power design in dashboard modules fed from 12V vehicle bus.
Empfohlen
Sensor Interface Module
The MC9S12C128MFUE serves as a sensor-interface MCU in industrial nodes where multiple analog and digital sensors converge before being relayed over CAN. The on-chip 10-bit ADC scans temperature, pressure, and flow sensors at sub-millisecond rates, and the 4KB RAM buffers time-stamped measurements before CAN transmission. SPI and I2C peripherals interface to digital sensors (accelerometers, gyros), while SCI (UART) is reserved for firmware debug. 128KB Flash is adequate for sensor-fusion algorithms and CANOpen stack. The 80-LQFP package and 25MHz HCS12 core fit within tight industrial cost envelopes.
Empfohlen
LIN Master in Body Electronics
The MC9S12C128MFUE acts as a LIN master in body-electronics networks where it controls slave nodes for window regulators, mirror adjusters, and lighting. The on-chip SCI (UART) plus timer module implements the LIN 2.x protocol without external components, while the HCS12 16-bit core at 25MHz comfortably schedules LIN frames at 19.2kbps. 128KB Flash fits LIN master application code plus network management tables. The internal 2.5V Vreg from a 5V/12V supply simplifies BOM, and 31 GPIOs drive slave enable lines. The 80-LQFP 14x14 mm footprint matches existing S12C body-network designs.
Empfohlen
Low-End Motor Control
The MC9S12C128MFUE drives low-end BLDC or stepper motor applications including HVAC blower control and small pumps where 25MHz CPU clock and 16-bit PWM resolution are sufficient. The on-chip timer modules with PWM outputs feed gate drivers for MOSFET bridges, and the 10-bit ADC reads back current sense for closed-loop torque control. 128KB Flash holds sensorless commutation algorithms plus CAN diagnostics. Compared with an ARM Cortex-M0, the HCS12 offers richer peripherals at similar cost for body-network motors. The 80-LQFP package's exposed thermal pad (where applicable) helps dissipate gate-drive switching losses.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MC9S12C128MFUE – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MC9S12C128CFUE | MC9S12C128VFUE | MC9S12E128CFUE | MC9S12E64CFUE |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 80-LQFP (14x14) | 80-LQFP (14x14) - same | 80-LQFP (14x14) - same | 80-LQFP (14x14) - same | 80-LQFP (14x14) - same |
| Core | HCS12 (CPU12) 16-bit | HCS12 16-bit | HCS12 16-bit | HCS12E (Enhanced) 16-bit | HCS12E (Enhanced) 16-bit |
| Maximum CPU Frequency | 25 MHz | 25 MHz | 25 MHz | 25 MHz | 25 MHz |
| Flash Memory | 128 KB | 128 KB | 128 KB | 128 KB | 64 KB (-50%) |
| RAM | 4 KB | 4 KB | 4 KB | 8 KB | 4 KB |
| CAN Controller | Yes (CAN 2.0) | Yes | Yes | Yes | Yes |
| ETPU Module | No | No | No | Yes (E-series) | Yes (E-series) |
| Supply Voltage | 2.97 V to 5.5 V | 2.97 V to 5.5 V | 2.97 V to 5.5 V | 2.97 V to 5.5 V | 2.97 V to 5.5 V |
Wichtigste Unterscheidungsmerkmale
- Cost-optimized C-series peripheral set (vs. MC9S12E128CFUE)
- Wide 5V supply range with internal Vreg (vs. MC9S12C128CFU (LQFP-48))
- Mature HCS12 ecosystem with CodeWarrior IDE (vs. ARM Cortex-M0 MCU alternatives)
Designhinweise
Place 1uF X7R ceramic decoupling caps as close as possible to each VDD/VDDR/VSS pair, plus a 10uF bulk cap on the main 5V supply rail. The internal bandgap Vreg draws transient current during bus-clock transitions and PLL frequency changes - inadequate decoupling causes VDD droop that can trigger spurious brown-out resets. The 5V external supply range per the NXP product overview lets the part share a rail with analog 5V sensors, simplifying power tree design in body controllers.
Estimated: at maximum 25MHz CPU clock with all peripherals active, the MC9S12C128MFUE draws approximately 30-50 mA from the 5V rail, dissipating 0.15-0.25 W. The 80-LQFP package has theta_JA around 50-60 C/W on a 2-layer PCB with no thermal pad, giving a junction temperature rise of roughly 10-15 C above ambient - well within the operating range. For automotive deployments above 85C ambient, derate by 30% and verify with a thermal probe on a worst-case ECU chassis.
Do not exceed 5.5V on VDD or apply voltage to any pin before VDD ramps - the absolute maximum ratings are 6V on supply pins. The background debug mode (BDM) interface pins (BKGD, MODC) must be left with proper pull-ups per the S12C reference manual to avoid unintended debug entry at reset. Confirm Flash security bytes are programmed correctly before mass production to prevent unauthorized firmware readback via BDM.
Use a 4-layer PCB stack-up with continuous ground plane beneath the MCU for best EMI/EMC performance, especially in automotive designs subject to CISPR 25. Route the CANH/CANL traces as an impedance-controlled differential pair (120 ohms) and keep them short and away from switching nodes. The 14x14 mm LQFP land pattern uses 0.65mm pitch - verify your assembly house can reliably solder this pitch, especially for prototypes.
Compliance-Informationen
RoHS compliant per distributor data. AEC-Q100 grade not explicitly stated in verified web data - contact NXP for automotive Q100 qualification status. M suffix may indicate automotive temperature grade; verify against the datasheet.
