MCP3426A7-E/MC - 16-Bit Dual-Channel Delta-Sigma ADC | Microchip
Teilenummer: MCP3426A7-E/MC ✓ AktivMCP3426A7-E/MC Übersicht
A delta-sigma ADC is a voltage-to-digital converter that uses oversampling and digital filtering to deliver high resolution and low noise. Within the semiconductor hierarchy, the MCP3426A7-E/MC is a data-converter IC, then an analog-to-digital converter, and finally a delta-sigma ADC. Its differential architecture measures the voltage difference between two inputs rather than the voltage relative to ground, making it useful when the signal source is balanced, floating, or centered around a common-mode voltage.
The MCP3426 family provides two analog input channels and conversion resolutions of up to 16 bits. The on-chip 2.048 V reference supports a differential range of +/-2.048 V, while the A7 device is configured for applications requiring the highest gain in this family. Digital filtering suppresses out-of-band noise, and the compact 8-DFN construction supports space-constrained analog measurement boards. The 15 SPS operating point prioritizes resolution and noise performance over rapid sampling.
The converter uses a sigma-delta modulation and digital-decimation architecture. Its internal reference, programmable gain stage, analog input network, and digital filter are combined to produce filtered conversion results. Differential operation rejects common-mode disturbances when the two input paths are balanced. Because this is a low-speed, high-resolution converter, the input-to-output latency and digital filter settling behavior must be considered when defining sample timing in firmware.
Typical uses include precision current measurement, bridge and sensor instrumentation, industrial process monitoring, laboratory measurement equipment, and portable instruments. In a current-sense application, the ADC can digitize the output of a current-sense amplifier. In a bridge circuit, the differential input can reduce sensitivity to common-mode voltage variations. The dual-channel architecture also allows simultaneous or interleaved measurement of two related quantities, depending on the converter mode and system timing.
PCB implementation should prioritize a quiet analog ground, short input traces, and placement of the external input filtering capacitors close to the associated pins. Digital communication traces should be kept away from the differential analog inputs to reduce conversion noise. Designers should also verify the required gain, common-mode range, settling time, and reference behavior against the manufacturer datasheet before fixing the front-end network.
This product page combines manufacturer specifications, practical application guidance, lifecycle-aware sourcing information, and same-package family alternatives. It also highlights the distinction between the A7 gain configuration and lower-gain MCP3426 devices, helping engineers select a replacement without assuming that every member of the converter family has identical measurement characteristics.
Drop-in-Alternativen für MCP3426A7-E/MC – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit MCP3426A7-E/MC (gleiche Bauform und Footprint) – abweichend in Differential Input Range, Package, Digital Interface, Number of Input Channels, Resolution.
MCP3426A0-E/MC
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →MCP3426A1-E/MC
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →MCP3426A2-E/MC
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MCP3426A3-E/MC
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
MCP3426A4-E/MC
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →MCP3426A5-E/MC
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →MCP3426A6-E/MC
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →MCP3426A7-E/MC Grenzwerte & elektrische Eigenschaften
| Converter Type | Delta-sigma analog-to-digital converter |
| Auflösung | 16 bits |
| Input Channels | 2 channels |
| Input Architecture | Differential inputs |
| Maximum Conversion Performance | 15 SPS |
| Internal Reference Voltage | 2.048 V |
| Differential Input Range | +/-2.048 V |
| Gain Configuration | A7 gain configuration |
| Gehäuse | 8-DFN, 2 x 3 mm |
| Montageart | Surface mount |
| Versorgungsspannung | 2.7 V to 5.5 V |
| Betriebstemperatur | -55 °C to +125 °C |
| Noise Performance | Low noise |
| Conversion Accuracy Class | High accuracy |
| Schnittstellentyp | Digital serial interface |
MCP3426A7-E/MC 8-dfn, 2 x 3 mm Pinbelegungsleitfaden
Pinbelegung für MCP3426A7-E/MC (8-dfn, 2 x 3 mm-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für MCP3426A7-E/MC.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MCP3426A7-E/MC ist geeignet für 6 Anwendungs: Precision Current Measurement, Industrial Sensor Acquisition, Portable Instrument Measurement, Bridge and Strain Measurement, Process and Environmental Monitoring, Battery and Power-System Monitoring.
Precision Current Measurement
The MCP3426A7-E/MC fits precision shunt-current measurement because its A7 gain configuration amplifies small differential voltages while the 16-bit converter preserves fine code resolution. The converter can digitize the output of a current-sense amplifier such as INA240A1PW, allowing a low-side shunt signal to be represented digitally without forcing a large common-mode voltage onto the ADC inputs. Its differential inputs also help reject common-mode variation when the amplifier and converter share a quiet reference ground. The primary trade-off is the reduced input range associated with the highest gain, so the shunt voltage, amplifier offset, and protection network must be scaled so that the largest transient remains inside the converter's input limits.
Empfohlen
Industrial Sensor Acquisition
The MCP3426A7-E/MC is appropriate for low-speed industrial sensor acquisition when the transducer produces a small differential output and the system prioritizes resolution over throughput. Its two differential input channels can support related measurements from bridge or sensing elements, while the internal 2.048 V reference provides a defined conversion span. An instrumentation front end such as INA149AIDR can translate a bipolar sensor signal into the converter's differential range. For factory equipment, the 15 SPS limit makes the device best suited to temperature, pressure, strain, and chemical-sensor monitoring rather than vibration waveforms or fast closed-loop control. Shielding, guarded analog routing, and calibration of offset and gain are essential for stable field measurements.
Empfohlen
Portable Instrument Measurement
The compact 8-DFN MCP3426A7-E/MC helps reduce board area in handheld meters and portable laboratory instruments where low-noise measurement of small differential voltages is important. Its 16-bit delta-sigma architecture, A7 gain, and two-channel capability support functions such as sensor calibration, current monitoring, and reference-voltage measurement without using two separate converter packages. A low-power microcontroller such as STM32G030F6P6TR can acquire filtered results and handle display, logging, and communications. The design trade-off is conversion latency: the digital filter and 15 SPS maximum rate require the firmware to distinguish a fresh conversion result from a settling or previously sampled code. Analog filtering and layout remain important even with an internal digital filter.
Empfohlen
Bridge and Strain Measurement
The MCP3426A7-E/MC can serve as the conversion stage for strain-gauge bridges, load cells, and other differential sensors whose output is small relative to the sensor excitation voltage. Differential input sampling reduces sensitivity to shared supply or ground disturbances, and the A7 gain increases sensitivity to millivolt-level bridge outputs. An amplifier such as INA149AIDR may be used when additional common-mode rejection, input impedance, or signal conditioning is required. The 15 SPS rate is adequate for static force, pressure, and position measurements, but it should not be assumed suitable for dynamic strain waveforms above the converter's specified rate. PCB creepage, input guarding, mechanical stress isolation, and temperature compensation determine whether the theoretical 16-bit resolution can be realized.
Empfohlen
Process and Environmental Monitoring
The MCP3426A7-E/MC is useful in slow process-control loops that monitor pressure, temperature, flow, or chemical concentration through low-level differential sensor outputs. Two input channels allow related variables to be measured while keeping the converter footprint compact, and the internal 2.048 V reference supports repeatable single-ended or differential measurements after appropriate conditioning. A microcontroller such as STM32G071RBT6TR can perform calibration, filtering, thresholding, and alarm handling. Because the converter is optimized for noise reduction at low conversion rates, system designers should allow sufficient settling time between configuration changes and readings. Calibration should include offset, gain, reference stability, and front-end drift rather than relying only on the nominal 16-bit converter resolution.
Empfohlen
Battery and Power-System Monitoring
The MCP3426A7-E/MC can monitor small differential voltages in battery-management and power-conversion systems when the relevant node voltage is scaled into its range. Its 16-bit conversion resolution and low-noise architecture are useful for pack-current, charger, or power-rail measurements where a few millivolts correspond to an important operating condition. A current-sense amplifier such as INA240A1PW can bridge the difference between a high-current shunt and the ADC's input limits. The slow 15 SPS maximum rate is appropriate for supervisory measurements rather than cycle-by-cycle converter protection. Designers must include input clamps, account for common-mode limits during fault conditions, and verify whether the internal reference is adequate for a production application or whether external referencing and calibration are preferred.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MCP3426A7-E/MC – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MCP3426A0-E/MC | MCP3426A1-E/MC | MCP3426A2-E/MC | MCP3426A3-E/MC | MCP3426A4-E/MC | MCP3426A5-E/MC | MCP3426A6-E/MC |
|---|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) | 8-DFN (2 x 3 mm) |
| Resolution | Up to 16 bits | Up to 16 bits | Up to 16 bits | Up to 16 bits | Up to 16 bits | Up to 16 bits | Up to 16 bits | Up to 16 bits |
| Input Channels | 2 differential inputs | 2 differential inputs | 2 differential inputs | 2 differential inputs | 2 differential inputs | 2 differential inputs | 2 differential inputs | 2 differential inputs |
| Conversion Performance | Up to 15 SPS | Up to 15 SPS | Up to 15 SPS | Up to 15 SPS | Up to 15 SPS | Up to 15 SPS | Up to 15 SPS | Up to 15 SPS |
| Internal Reference | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V |
| Gain Configuration | A7, 128x | A0, 1x | A1, 2x | A2, 4x | A3, 8x | A4, 16x | A5, 32x | A6, 64x |
| Differential Input Range | +/-2.048 V at the configured gain | +/-2.048 V at 1x gain | +/-2.048 V at 2x gain | +/-2.048 V at 4x gain | +/-2.048 V at 8x gain | +/-2.048 V at 16x gain | +/-2.048 V at 32x gain | +/-2.048 V at 64x gain |
| Supply Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
Wichtigste Unterscheidungsmerkmale
- Highest-gain option in the MCP3426 family (vs. MCP3426A6-E/MC)
- Higher resolution for small bridge and shunt signals (vs. MCP3426A0-E/MC)
- Differential measurement with an integrated precision reference (vs. MCP3426A1-E/MC)
Designhinweise
Route the two differential input channels as a compact, balanced pair and connect input-filtering components directly to the converter pins. Keep the digital interface traces away from the analog inputs, especially the clock and serial-data lines. A solid analog ground plane with a controlled connection to the system ground can reduce potential differences between the input pair. Use the manufacturer package drawing and pin-description table when defining the 8-DFN land pattern and exposed-pad connection.
Treat analog filtering as part of the complete conversion system rather than an afterthought. Place any differential input capacitors close to the converter, select their values using the manufacturer noise and settling guidance, and verify that capacitor tolerance does not unbalance the two input paths. An amplifier with adequate common-mode range and low-noise behavior is necessary when the measured signal does not naturally fit the converter's input window. Check offset, bias current, and settling time before relying on the nominal 16-bit resolution.
The highest A7 gain increases sensitivity to small differential signals but also reduces the usable input range and can amplify front-end offset and noise. Validate the maximum signal, startup transient, and fault condition against the common-mode and absolute input limits before finalizing the amplifier or shunt network. Also allow the digital filter to settle after gain or configuration changes; treating the most recent code as an immediate measurement can introduce systematic errors.
Separate the analog measurement section from switching regulators, high-current power paths, and digital clocks. Use a continuous ground reference beneath the converter where practical, avoid routing input traces beneath noisy package or board features, and keep supply-decoupling placement consistent with the manufacturer layout guidance. If a shunt or sensitive bridge is used, consider guarding, creepage, cleaning requirements, and thermal gradients because these mechanical and contamination effects can dominate the converter's theoretical noise performance.
Compliance-Informationen
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for the exact MCP3426A7-E/MC ordering code. Confirm current environmental and qualification documentation with Microchip before release to production.