Microchip Technology

MCP3426A7-E/MC - 16-Bit Dual-Channel Delta-Sigma ADC | Microchip

MPN: MCP3426A7-E/MC ✓ Nakahanda
2.048 V Vdss 8-DFN, 2 x 3 mm Package
MOQ: 1 |

MCP3426A7-E/MC Ulas

Microchip Technology MCP3426A7-E/MC is a 16-bit, dual-channel delta-sigma analog-to-digital converter with differential inputs, up to 15 SPS conversion performance, and an 8-DFN package measuring 2 x 3 mm. It belongs to the low-noise, high-accuracy MCP3426/7/8 converter family and includes an on-board precision 2.048 V reference for a differential input range of +/-2.048 V. The A7 gain configuration is designed for fine-resolution measurement of comparatively small differential signals.

A delta-sigma ADC is a voltage-to-digital converter that uses oversampling and digital filtering to deliver high resolution and low noise. Within the semiconductor hierarchy, the MCP3426A7-E/MC is a data-converter IC, then an analog-to-digital converter, and finally a delta-sigma ADC. Its differential architecture measures the voltage difference between two inputs rather than the voltage relative to ground, making it useful when the signal source is balanced, floating, or centered around a common-mode voltage.

The MCP3426 family provides two analog input channels and conversion resolutions of up to 16 bits. The on-chip 2.048 V reference supports a differential range of +/-2.048 V, while the A7 device is configured for applications requiring the highest gain in this family. Digital filtering suppresses out-of-band noise, and the compact 8-DFN construction supports space-constrained analog measurement boards. The 15 SPS operating point prioritizes resolution and noise performance over rapid sampling.

The converter uses a sigma-delta modulation and digital-decimation architecture. Its internal reference, programmable gain stage, analog input network, and digital filter are combined to produce filtered conversion results. Differential operation rejects common-mode disturbances when the two input paths are balanced. Because this is a low-speed, high-resolution converter, the input-to-output latency and digital filter settling behavior must be considered when defining sample timing in firmware.

Typical uses include precision current measurement, bridge and sensor instrumentation, industrial process monitoring, laboratory measurement equipment, and portable instruments. In a current-sense application, the ADC can digitize the output of a current-sense amplifier. In a bridge circuit, the differential input can reduce sensitivity to common-mode voltage variations. The dual-channel architecture also allows simultaneous or interleaved measurement of two related quantities, depending on the converter mode and system timing.

PCB implementation should prioritize a quiet analog ground, short input traces, and placement of the external input filtering capacitors close to the associated pins. Digital communication traces should be kept away from the differential analog inputs to reduce conversion noise. Designers should also verify the required gain, common-mode range, settling time, and reference behavior against the manufacturer datasheet before fixing the front-end network.

This product page combines manufacturer specifications, practical application guidance, lifecycle-aware sourcing information, and same-package family alternatives. It also highlights the distinction between the A7 gain configuration and lower-gain MCP3426 devices, helping engineers select a replacement without assuming that every member of the converter family has identical measurement characteristics.

Mga alternatibo na pwedeng ilagay na MCP3426A7-E/MC — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok MCP3426A7-E/MC (parehas na form factor at footprint) — pagkakaiba sa Differential Input Range, Package, Digital Interface, Number of Input Channels, Resolution.

Microchip Technology
Differential Input Range: ±2.048 V
Package: 8-DFN (2 x 3 mm)
Digital Interface: Two-wire I2C
Microchip Technology
Differential Input Range: ±2.048 V
Package: 8-DFN (2 x 3 mm)
Digital Interface: I2C

MCP3426A0-E/MC

✅ Drop-In
Microchip Technology
📦 8-DFN (2 x 3 mm)
16 bit · 2 channels · Differential · Delta-sigma · 15 samples/s · 2.048 V · ±2.048 V · 2.7 V to 5.5 V

Magkontak para sa presyo

Tingnan ang Datasheet →

MCP3426A1-E/MC

✅ Drop-In
Microchip Technology
📦 8-DFN (2 x 3 mm)
Up to 16 bits · 2 · Delta-sigma · Differential · 240 samples/s · 2.048 V · ±2.048 V · Two-wire I2C

Magkontak para sa presyo

Tingnan ang Datasheet →

MCP3426A2-E/MC

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
📦 8-DFN (2 x 3 mm)
Same 8-DFN footprint and converter, but gain changes from A7 to A2; A7 provides 32 times the A2 signal gain, reducing full-scale input range by approximately 96.9%

📋 Alternatibo na Reference (hindi sa katalogo)

MCP3426A3-E/MC

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
📦 8-DFN (2 x 3 mm)
Same 8-DFN footprint and converter, but gain changes from A7 to A3; A7 provides 16 times the A3 signal gain, reducing full-scale input range by approximately 93.8%

📋 Alternatibo na Reference (hindi sa katalogo)

MCP3426A4-E/MC

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Microchip Technology
📦 8-DFN (2 x 3 mm)
16 bit · 2 channels · Differential · Delta-sigma · 15 samples/s · 2.048 V · ±2.048 V · I2C

Magkontak para sa presyo

Tingnan ang Datasheet →

MCP3426A5-E/MC

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Microchip Technology
📦 8-DFN (2 x 3 mm)
Delta-sigma analog-to-digital converter · Up to 16 bits · 2 channels · Differential inputs · 15 SPS · 2.048 V · ±2.048 V · 2.7 V to 5.5 V

Magkontak para sa presyo

Tingnan ang Datasheet →

MCP3426A6-E/MC

✅ Drop-In
Microchip Technology
📦 8-DFN (2 x 3 mm)
16-bit delta-sigma ADC · 2 channels · 15 SPS · Up to 16 bits · Differential inputs · 2.048 V · ±2.048 V · Two-wire I2C

Magkontak para sa presyo

Tingnan ang Datasheet →

MCP3426A7-E/MC Mga Pinakamataas na Rating at Electrical Characteristics

Converter Type Delta-sigma analog-to-digital converter
Pangangasiwaan 16 bits
Input Channels 2 channels
Input Architecture Differential inputs
Maximum Conversion Performance 15 SPS
Internal Reference Voltage 2.048 V
Differential Input Range +/-2.048 V
Gain Configuration A7 gain configuration
Packhaging 8-DFN, 2 x 3 mm
Uri ng Pagpapasok Surface mount
Volte ng Pagbibigay 2.7 V to 5.5 V
Temperature na Operasyon -55 °C to +125 °C
Noise Performance Low noise
Conversion Accuracy Class High accuracy
Uri ng Interface Digital serial interface

Gabay sa Pin Configuration ng MCP3426A7-E/MC 8-dfn, 2 x 3 mm

Pin configuration para sa MCP3426A7-E/MC (8-dfn, 2 x 3 mm package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.

Pinout diagram ng 8-dfn, 2 x 3 mm package para sa MCP3426A7-E/MC

Wala ng detalyadong pinout data na magagamit para sa MCP3426A7-E/MC.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

MCP3426A7-E/MC ay nararapat para sa 6 aplikasyons: Precision Current Measurement, Industrial Sensor Acquisition, Portable Instrument Measurement, Bridge and Strain Measurement, Process and Environmental Monitoring, Battery and Power-System Monitoring.

⚡

Precision Current Measurement

The MCP3426A7-E/MC fits precision shunt-current measurement because its A7 gain configuration amplifies small differential voltages while the 16-bit converter preserves fine code resolution. The converter can digitize the output of a current-sense amplifier such as INA240A1PW, allowing a low-side shunt signal to be represented digitally without forcing a large common-mode voltage onto the ADC inputs. Its differential inputs also help reject common-mode variation when the amplifier and converter share a quiet reference ground. The primary trade-off is the reduced input range associated with the highest gain, so the shunt voltage, amplifier offset, and protection network must be scaled so that the largest transient remains inside the converter's input limits.

🏭

Industrial Sensor Acquisition

The MCP3426A7-E/MC is appropriate for low-speed industrial sensor acquisition when the transducer produces a small differential output and the system prioritizes resolution over throughput. Its two differential input channels can support related measurements from bridge or sensing elements, while the internal 2.048 V reference provides a defined conversion span. An instrumentation front end such as INA149AIDR can translate a bipolar sensor signal into the converter's differential range. For factory equipment, the 15 SPS limit makes the device best suited to temperature, pressure, strain, and chemical-sensor monitoring rather than vibration waveforms or fast closed-loop control. Shielding, guarded analog routing, and calibration of offset and gain are essential for stable field measurements.

🖥️

Portable Instrument Measurement

The compact 8-DFN MCP3426A7-E/MC helps reduce board area in handheld meters and portable laboratory instruments where low-noise measurement of small differential voltages is important. Its 16-bit delta-sigma architecture, A7 gain, and two-channel capability support functions such as sensor calibration, current monitoring, and reference-voltage measurement without using two separate converter packages. A low-power microcontroller such as STM32G030F6P6TR can acquire filtered results and handle display, logging, and communications. The design trade-off is conversion latency: the digital filter and 15 SPS maximum rate require the firmware to distinguish a fresh conversion result from a settling or previously sampled code. Analog filtering and layout remain important even with an internal digital filter.

📱

Bridge and Strain Measurement

The MCP3426A7-E/MC can serve as the conversion stage for strain-gauge bridges, load cells, and other differential sensors whose output is small relative to the sensor excitation voltage. Differential input sampling reduces sensitivity to shared supply or ground disturbances, and the A7 gain increases sensitivity to millivolt-level bridge outputs. An amplifier such as INA149AIDR may be used when additional common-mode rejection, input impedance, or signal conditioning is required. The 15 SPS rate is adequate for static force, pressure, and position measurements, but it should not be assumed suitable for dynamic strain waveforms above the converter's specified rate. PCB creepage, input guarding, mechanical stress isolation, and temperature compensation determine whether the theoretical 16-bit resolution can be realized.

🧩

Process and Environmental Monitoring

The MCP3426A7-E/MC is useful in slow process-control loops that monitor pressure, temperature, flow, or chemical concentration through low-level differential sensor outputs. Two input channels allow related variables to be measured while keeping the converter footprint compact, and the internal 2.048 V reference supports repeatable single-ended or differential measurements after appropriate conditioning. A microcontroller such as STM32G071RBT6TR can perform calibration, filtering, thresholding, and alarm handling. Because the converter is optimized for noise reduction at low conversion rates, system designers should allow sufficient settling time between configuration changes and readings. Calibration should include offset, gain, reference stability, and front-end drift rather than relying only on the nominal 16-bit converter resolution.

🔋

Battery and Power-System Monitoring

The MCP3426A7-E/MC can monitor small differential voltages in battery-management and power-conversion systems when the relevant node voltage is scaled into its range. Its 16-bit conversion resolution and low-noise architecture are useful for pack-current, charger, or power-rail measurements where a few millivolts correspond to an important operating condition. A current-sense amplifier such as INA240A1PW can bridge the difference between a high-current shunt and the ADC's input limits. The slow 15 SPS maximum rate is appropriate for supervisory measurements rather than cycle-by-cycle converter protection. Designers must include input clamps, account for common-mode limits during fault conditions, and verify whether the internal reference is adequate for a production application or whether external referencing and calibration are preferred.

What is the MCP3426A7-E/MC?
The MCP3426A7-E/MC is a Microchip Technology 16-bit, dual-channel delta-sigma ADC in an 8-DFN package. It provides differential inputs, an internal 2.048 V reference, and conversion rates up to 15 SPS. According to the Microchip MCP3426/7/8 datasheet, the device is designed for low-noise, high-accuracy analog measurement where resolution is more important than high-speed sampling.
What is the resolution and conversion rate of MCP3426A7-E/MC?
The MCP3426A7-E/MC converts analog differential signals into digital codes with up to 16 bits of resolution at rates up to 15 SPS. The Microchip MCP3426/7/8 datasheet identifies the converter as a low-noise, high-accuracy delta-sigma ADC. The relatively low sample rate allows the digital filter to suppress noise and favors precision instrumentation rather than waveform capture or high-speed control.
What is the input voltage range of MCP3426A7-E/MC?
The MCP3426A7-E/MC supports a differential input range of +/-2.048 V when operated with its on-board 2.048 V precision reference. According to the Microchip product page, the MCP3426 uses differential inputs and its internal reference establishes this measurement span. The common-mode voltage and signal headroom must also remain within the limits specified for the selected gain and operating condition.
Where can I download the MCP3426A7-E/MC datasheet PDF?
The official MCP3426A7-E/MC datasheet PDF is available through the Microchip MCP3426/7/8 data sheet at https://ww1.microchip.com/downloads/aemDocuments/documents/OTH/ProductDocuments/DataSheets/22226a.pdf. Use that manufacturer document for the complete pin description, electrical characteristics, gain table, timing information, typical application circuits, and recommended decoupling values for the MCP3426 family.
Where can I find the MCP3426A7-E/MC pinout?
The MCP3426A7-E/MC pinout is shown in the pin-description section of the Microchip MCP3426/7/8 manufacturer data sheet. The device is an 8-DFN package measuring 2 x 3 mm. Before assigning PCB tracks, use the package drawing and pin-description table together because the exposed pad and numbering must follow the manufacturer drawing rather than an inferred generic DFN layout.
Is the MCP3426A7-E/MC suitable for low-current measurements?
The MCP3426A7-E/MC is suitable for precision low-current measurement when its A7 gain setting is matched to the shunt voltage and the front-end amplifier does not overload the inputs. Its 16-bit resolution and low-noise delta-sigma architecture can resolve small differential signals, while the +/-2.048 V reference range supports a usable full-scale span. Input leakage, bias current, amplifier offset, and PCB contamination must also be considered.
How does MCP3426A7-E/MC compare with MCP3426A0-E/MC?
MCP3426A7-E/MC is the highest-gain A7 member, while MCP3426A0-E/MC is the lowest-gain A0 member; both use the same 8-DFN package and core delta-sigma converter. The important difference is signal amplification before conversion: A7 offers greater sensitivity to small differential signals, whereas A0 accommodates a larger input signal. Select the variant whose gain and input range fit the front end without overdriving it.
What is the difference between MCP3426A7-E/MC and MCP3426A6-E/MC?
MCP3426A7-E/MC and MCP3426A6-E/MC share the 8-DFN package and 16-bit delta-sigma conversion architecture, but their gain configurations differ by one step. A7 provides the higher sensitivity for smaller differential signals, while A6 allows a larger input range. The MCP3426 family datasheet should be used to confirm the exact gain, common-mode limits, and conversion timing before substituting one variant in a specific design.
When should I choose MCP3426A7-E/MC over MCP3426A6-E/MC?
Choose MCP3426A7-E/MC when the measured differential signal is small enough that the A7 gain improves resolution without driving the analog input stage beyond its common-mode range. Choose MCP3426A6-E/MC when a wider signal range or more headroom is needed. Both devices use the same physical package, so the decision should be based on front-end voltage, noise contribution, saturation margin, and required accuracy.
What can replace the MCP3426A7-E/MC?
The closest same-package replacement is the MCP3426A7T-E/MC, which retains the A7 conversion configuration in a different orderable package form, although the shipping format must be checked before assembly. Lower-gain MCP3426A0-E/MC through MCP3426A6-E/MC devices can preserve the footprint but change signal gain and input range. Confirm the manufacturer ordering information and application limits before any substitution.
What is the best drop-in replacement for MCP3426A7-E/MC?
MCP3426A7-E/MC is the primary 8-DFN, 2 x 3 mm ordering form, so a like-for-like replacement must preserve that package, pin arrangement, A7 gain configuration, supply range, and conversion interface. MCP3426A7T-E/MC is the closest identified family alternative, while lower-gain A0 through A6 parts alter signal conditioning. Use the MCP3426/7/8 datasheet and package drawings for final approval.
Is there a Microchip equivalent for the MCP3426A7-E/MC?
Microchip Technology offers several MCP3426 family configurations in the same 8-DFN format, including MCP3426A0-E/MC, MCP3426A1-E/MC, MCP3426A2-E/MC, MCP3426A3-E/MC, MCP3426A4-E/MC, MCP3426A5-E/MC, and MCP3426A6-E/MC. These are pin-compatible family alternatives, but their gain settings differ from A7, so they are not equivalent without validating signal range and accuracy.
Where can I buy MCP3426A7-E/MC online?
Use the Request a Quote form on this page to request MCP3426A7-E/MC availability, current commercial terms, and a suitable order quantity. The form is the appropriate route for quote-first electronic component sourcing and can clarify assembly packaging, date-code requirements, and lead time. Avoid approving a purchase until the exact MCP3426A7-E/MC ordering code has been confirmed.
What is the price of MCP3426A7-E/MC?
Use the Request a Quote form on this page for the current MCP3426A7-E/MC commercial price and quantity breaks. Pricing can vary with order quantity, assembly form, date code, and market conditions, so a static figure would not reliably represent the current offer. The quote form allows the exact part number and purchasing requirements to be included in the request.
What is the lead time and stock status for MCP3426A7-E/MC?
Request the current MCP3426A7-E/MC stock status, lead time, and minimum order quantity through the Request a Quote form on this page. Distributor search snippets can reflect changing inventory rather than a guaranteed allocation, so they should not be treated as a firm stock commitment. Include your required quantity, date-code preference, and target delivery date in the request.
What are the key specifications of MCP3426A7-E/MC that engineers should know?
The MCP3426A7-E/MC combines two differential analog inputs, 16-bit resolution, conversion performance up to 15 SPS, an on-board 2.048 V reference, and an 8-DFN package measuring 2 x 3 mm. According to the Microchip MCP3426/7/8 datasheet, it is a low-noise, high-accuracy delta-sigma converter. The A7 configuration is especially relevant to small differential signals where gain and noise determine usable measurement resolution.

Impormasyon ng Talumpati sa Engineering for MCP3426A7-E/MC — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose MCP3426A7-E/MC when the application measures a small differential voltage and the front end can keep transients, offset, and common-mode voltage within the A7 operating limits. Its 128x gain is appropriate for millivolt-level shunt, bridge, or sensor signals, and the 16-bit delta-sigma architecture favors precision over speed. Choose MCP3426A6-E/MC or MCP3426A5-E/MC when more input headroom is valuable and the desired resolution can still be met. Use MCP3426A0-E/MC through MCP3426A4-E/MC for progressively larger signals. Although these parts share the 8-DFN footprint and conversion architecture, changing gain can alter full-scale range, effective resolution, noise behavior, and firmware configuration. For any substitution, verify the manufacturer gain table, common-mode limits, settling behavior, exposed-pad layout, and calibration procedure. The 15 SPS rate is suited to static or slow-changing measurements, not high-bandwidth waveform acquisition.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto MCP3426A0-E/MC MCP3426A1-E/MC MCP3426A2-E/MC MCP3426A3-E/MC MCP3426A4-E/MC MCP3426A5-E/MC MCP3426A6-E/MC
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 8-DFN (2 x 3 mm) 8-DFN (2 x 3 mm) 8-DFN (2 x 3 mm) 8-DFN (2 x 3 mm) 8-DFN (2 x 3 mm) 8-DFN (2 x 3 mm) 8-DFN (2 x 3 mm) 8-DFN (2 x 3 mm)
Resolution Up to 16 bits Up to 16 bits Up to 16 bits Up to 16 bits Up to 16 bits Up to 16 bits Up to 16 bits Up to 16 bits
Input Channels 2 differential inputs 2 differential inputs 2 differential inputs 2 differential inputs 2 differential inputs 2 differential inputs 2 differential inputs 2 differential inputs
Conversion Performance Up to 15 SPS Up to 15 SPS Up to 15 SPS Up to 15 SPS Up to 15 SPS Up to 15 SPS Up to 15 SPS Up to 15 SPS
Internal Reference 2.048 V 2.048 V 2.048 V 2.048 V 2.048 V 2.048 V 2.048 V 2.048 V
Gain Configuration A7, 128x A0, 1x A1, 2x A2, 4x A3, 8x A4, 16x A5, 32x A6, 64x
Differential Input Range +/-2.048 V at the configured gain +/-2.048 V at 1x gain +/-2.048 V at 2x gain +/-2.048 V at 4x gain +/-2.048 V at 8x gain +/-2.048 V at 16x gain +/-2.048 V at 32x gain +/-2.048 V at 64x gain
Supply Voltage 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V 2.7 V to 5.5 V

Pangunahing mga Pagkakaiba

  • Highest-gain option in the MCP3426 family (kumpara saMCP3426A6-E/MC)
  • Higher resolution for small bridge and shunt signals (kumpara saMCP3426A0-E/MC)
  • Differential measurement with an integrated precision reference (kumpara saMCP3426A1-E/MC)

Talaan ng Disenyo

Route the two differential input channels as a compact, balanced pair and connect input-filtering components directly to the converter pins. Keep the digital interface traces away from the analog inputs, especially the clock and serial-data lines. A solid analog ground plane with a controlled connection to the system ground can reduce potential differences between the input pair. Use the manufacturer package drawing and pin-description table when defining the 8-DFN land pattern and exposed-pad connection.

Treat analog filtering as part of the complete conversion system rather than an afterthought. Place any differential input capacitors close to the converter, select their values using the manufacturer noise and settling guidance, and verify that capacitor tolerance does not unbalance the two input paths. An amplifier with adequate common-mode range and low-noise behavior is necessary when the measured signal does not naturally fit the converter's input window. Check offset, bias current, and settling time before relying on the nominal 16-bit resolution.

The highest A7 gain increases sensitivity to small differential signals but also reduces the usable input range and can amplify front-end offset and noise. Validate the maximum signal, startup transient, and fault condition against the common-mode and absolute input limits before finalizing the amplifier or shunt network. Also allow the digital filter to settle after gain or configuration changes; treating the most recent code as an immediate measurement can introduce systematic errors.

Separate the analog measurement section from switching regulators, high-current power paths, and digital clocks. Use a continuous ground reference beneath the converter where practical, avoid routing input traces beneath noisy package or board features, and keep supply-decoupling placement consistent with the manufacturer layout guidance. If a shunt or sensitive bridge is used, consider guarding, creepage, cleaning requirements, and thermal gradients because these mechanical and contamination effects can dominate the converter's theoretical noise performance.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for the exact MCP3426A7-E/MC ordering code. Confirm current environmental and qualification documentation with Microchip before release to production.

Data napatotohanan sa: 2026-11-15 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

MCP3426A7-E/MC MCP3426A7-E/MC datasheet MCP3426A7-E/MC datasheet pdf MCP3426A7-E/MC pinout MCP3426A7-E/MC equivalent MCP3426A7-E/MC replacement MCP3426A7-E/MC price MCP3426A7-E/MC stock Microchip MCP3426A7-E/MC MCP3426A7-E/MC 8-DFN MCP3426A7-E/MC vs MCP3426A6-E/MC MCP3426 16-bit dual-channel ADC MCP3426 2.048V differential ADC MCP3426 application circuit

Mga kaugnay na Mga Komponente at mga Tuntunin

Microchip Technology MCP3426A7-E/MC MCP3426A0-E/MC MCP3426A1-E/MC MCP3426A2-E/MC MCP3426A3-E/MC MCP3426A4-E/MC MCP3426A5-E/MC MCP3426A6-E/MC MCP3426 delta-sigma ADC analog-to-digital converter data-converter IC semiconductor differential input programmable gain amplifier 16-bit resolution 2.048 V internal reference 15 SPS conversion rate 8-DFN package DFN family surface-mount package precision current measurement bridge sensor instrumentation
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ