Microchip Technology

MCP601T-I/ST - 2.8MHz Rail-to-Rail CMOS Op Amp | Microchip

Teilenummer: MCP601T-I/ST ✓ Aktiv
<2 mV Vdss 230 uA Id 8-pin TSSOP Package
MOQ: 1 |

MCP601T-I/ST Übersicht

The Microchip Technology MCP601T-I/ST is a single-circuit, general-purpose operational amplifier with a 2.8 MHz gain-bandwidth product, rail-to-rail output operation, and a typical operating current of 230 uA in an 8-pin TSSOP package. Its typical input offset voltage is less than 2 mV, while the listed input bias-current characteristic is 1 pA. The MCP601 family uses Microchip's advanced CMOS technology and is intended for low-power, low-voltage analog signal-conditioning circuits.

An operational amplifier, or op amp, is an analog integrated circuit that uses high-gain differential feedback to amplify a voltage difference. It belongs to the amplifier IC hierarchy: operational amplifier -> voltage-feedback amplifier -> analog signal conditioning -> semiconductor. The rail-to-rail output architecture allows the output to approach the available supply rails more closely than a conventional fixed-headroom output stage, which is valuable in compact systems that require a usable output swing from a low-voltage supply.

The MCP601T-I/ST combines a 2.8 MHz gain-bandwidth product with low typical operating current of 230 uA. Its listed typical input offset voltage is below 2 mV, and the LCSC product listing identifies a 1 pA input bias-current figure. A slew rate of 2.3 V/us is also listed for the device. These characteristics place it between general-purpose signal amplification and low-power acquisition applications where low quiescent consumption and rail-to-rail output capability are more important than very high bandwidth.

The MCP601 uses advanced CMOS technology to support low-power operation and high input impedance. Rail-to-rail output capability is particularly useful for buffer, transducer, and sensor-interface stages that operate near either supply rail. Designers should still account for input common-mode range, output swing, noise, stability with the selected feedback network, and decoupling when applying the amplifier outside its simplest voltage-follower configuration. The exact MCP601T-I/ST ordering suffix identifies the industrial temperature and TSSOP packaging option.

Typical uses include low-power sensor conditioning, battery-powered instrumentation, ADC input buffering, current-to-voltage conversion with a feedback resistor, general signal amplification, and unity-gain buffers. The 8-TSSOP package supports compact PCB layouts, while the 230 uA typical operating current helps reduce the energy burden in continuously powered systems. Because the listed 2.8 MHz bandwidth is modest compared with high-speed amplifiers, the MCP601T-I/ST is best suited to low- and intermediate-frequency signal paths rather than wideband pulse or video amplification.

For a new design, use the manufacturer datasheet pin description and typical-application circuit when assigning pins and compensation or feedback values. Keep input and output nodes short, provide local supply bypassing, and verify the input common-mode and output-voltage limits against the actual operating rail. The Request a Quote form on this page provides current commercial availability, lead-time, and order information without embedding a static price.

This product page combines manufacturer specifications, package information, practical design guidance, drop-in replacement analysis, and a parameter comparison for the MCP601T-I/ST. It also distinguishes the verified TSSOP option from other MCP601 package and ordering variants, helping engineers identify a suitable replacement before committing to a PCB revision.

Drop-in-Alternativen für MCP601T-I/ST – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit MCP601T-I/ST (gleiche Bauform und Footprint) – abweichend in Number of Circuits, Package, Amplifier Type, Supply Voltage Range, Technology.

Microchip Technology
Number of Circuits: 1
Package: 8-lead TSSOP
Amplifier Type: Single general-purpose CMOS operational amplifier
Microchip Technology
Number of Circuits: 1
Amplifier Type: Single general-purpose operational amplifier
Supply Voltage Range: 2.7 V to 6.0 V

MCP601-I/ST

✅ Drop-In
Microchip Technology
📦 8-pin TSSOP
Single general-purpose CMOS operational amplifier · 1 · 2.7 V to 5.5 V · 2.7 V · 5.5 V · Rail-to-rail · Less than 325 uA · CMOS

Preis auf Anfrage

Datenblatt ansehen →

MCP601T-I/ST Grenzwerte & elektrische Eigenschaften

Number of Circuits 1 circuit
Product Type General-purpose operational amplifier
Gain-Bandwidth Product 2.8 MHz
Typical Operating Current 230 uA
Typical Input Offset Voltage <2 mV
Input Bias Current 1 pA
Slew Rate 2.3 V/us
Ausgangstyp Rail-to-rail
Technology Advanced CMOS
Minimum Supply Voltage 2.7 V
Maximum Supply Voltage 6 V
Gehäuse 8-pin TSSOP
Montageart Surface mount

MCP601T-I/ST 8-pin tssop Pinbelegungsleitfaden

Pinbelegung für MCP601T-I/ST (8-pin tssop-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.

Pinbelegungsdiagramm für MCP601T-I/ST im 8-pin tssop-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für MCP601T-I/ST.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

MCP601T-I/ST ist geeignet für 6 Anwendungs: Low-Power Sensor Conditioning, Battery-Powered Instrumentation, ADC Input Buffering, Current-to-Voltage Conversion, General Signal Amplification, Precision Analog Signal Conditioning.

🧩

Low-Power Sensor Conditioning

The MCP601T-I/ST fits low-power sensor conditioning because it combines a listed 1 pA input bias current with less than 2 mV typical input offset voltage and a 2.8 MHz gain-bandwidth product. Place the amplifier in a non-inverting or differential stage when the sensor output permits, then use the feedback network to establish the required gain while preserving sensor bandwidth. Its 230 uA typical operating current is useful in continuously powered instrumentation. The key trade-off is that the 2.8 MHz gain-bandwidth product limits high-gain operation at higher frequencies, so verify the closed-loop response and noise bandwidth before finalizing the sensor interface.

⚡

Battery-Powered Instrumentation

The MCP601T-I/ST is appropriate for battery-powered instrumentation that requires signal amplification without a continuously high-power analog stage. Its 230 uA typical operating current and 2.7 V minimum supply voltage support compact low-voltage systems, while the rail-to-rail output provides useful signal swing near the supply limits. The amplifier can buffer a transducer or condition a control signal before an ADC input. Because amplifier current is only one part of total consumption, include sensor, ADC, reference, and regulator consumption in the system budget, and check output loading and input common-mode limits at the lowest operating voltage.

📡

ADC Input Buffering

The MCP601T-I/ST can serve as an ADC input buffer when the converter requires a low-impedance drive and the source signal does not need the bandwidth of a high-speed amplifier. Its listed 1 pA input bias current reduces loading on high-impedance sources, and the less-than-2 mV typical offset can help preserve low-level signal accuracy. Use a unity-gain follower or the required gain configuration and place the amplifier close to the ADC input to minimize trace pickup. Validate settling time, capacitive loading, output swing, and the ADC's acquisition window, since the 2.8 MHz gain-bandwidth product does not guarantee fast settling for every gain and load.

📷

Current-to-Voltage Conversion

The MCP601T-I/ST can convert a small current into a voltage in a transimpedance amplifier used with photodiodes, sensors, or current-output transducers. The listed 1 pA input bias current is a useful starting point for high-impedance feedback arrangements, while rail-to-rail output helps use more of the available signal range. Choose the feedback resistor and compensation capacitance from the source capacitance and target bandwidth requirements. Verify stability, input bias effects, noise, and output-current capability because a general-purpose 2.8 MHz amplifier is intended for modest-bandwidth precision functions rather than very fast photodiode transimpedance designs.

🔧

General Signal Amplification

The MCP601T-I/ST is suitable for general signal amplification in small analog boards that need a single amplifier with rail-to-rail output. Its 2.8 MHz gain-bandwidth product supports low-frequency and moderate-bandwidth waveforms, while the 230 uA typical operating current suits compact and portable equipment. Configure the closed-loop gain with conventional feedback resistors and verify the resulting bandwidth, output swing, and distortion. The 8-pin TSSOP package permits a small footprint, but decoupling and grounding still require careful layout. For audio, measurement, or industrial channels requiring lower noise or narrower offset, compare the measured requirements against the amplifier's full datasheet limits.

🏭

Precision Analog Signal Conditioning

The MCP601T-I/ST can condition low-level analog signals in measurement and control systems where rail-to-rail output and low typical operating current are useful. Its typical input offset voltage below 2 mV and 2.8 MHz gain-bandwidth product are meaningful for many precision, low-to-moderate-frequency paths. The amplifier should be evaluated for offset drift, noise, common-mode rejection, and gain error under the required temperature range rather than relying only on typical figures. Use a clean reference, stable feedback resistors, local bypass capacitors, and grounded return paths. For instrumentation requiring gain error or noise substantially below the general-purpose MCP601 performance, select a precision amplifier instead.

Zusammenfassung der empfohlenen Produkte

What are the key specifications of MCP601T-I/ST that engineers should know?
The MCP601T-I/ST is a single-circuit, rail-to-rail CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 230 uA typical operating current, input offset voltage below 2 mV, and an 8-pin TSSOP package. The device is listed with 1 pA input bias current and a 2.3 V/us slew rate. According to the Microchip MCP601 product page, the family uses advanced CMOS technology and operates from a minimum supply voltage of 2.7 V. These figures position it as a low-power general-purpose amplifier for sensor, buffer, and low-frequency signal-conditioning stages rather than a high-speed video amplifier.
What is the operating voltage of MCP601T-I/ST?
The MCP601T-I/ST operates from a minimum supply voltage of 2.7 V, with a maximum supply voltage of 6 V. The Mouser listing identifies the MCP601 as a single 2.7 V operational amplifier, while the Microchip family information supports the low-voltage CMOS design. Actual usable signal range remains narrower than the total supply range because input common-mode voltage and output swing have finite limits. Use the manufacturer MCP601 datasheet to verify those limits for the chosen supply voltage, input bias, and output load before finalizing the circuit.
What is the gain-bandwidth product of MCP601T-I/ST?
The MCP601T-I/ST has a 2.8 MHz gain-bandwidth product, as stated on the Microchip product page and confirmed by the Octopart and LCSC product descriptions. This bandwidth supports general-purpose amplification and buffering of low-to-moderate-frequency signals. The related listed slew rate is 2.3 V/us. For practical closed-loop use, the achievable signal bandwidth also depends on the selected noise gain, load impedance, feedback network, and amplifier stability, so the 2.8 MHz figure should not be treated as the closed-loop bandwidth for every circuit.
How much current does MCP601T-I/ST typically consume?
The MCP601T-I/ST has a typical operating current of 230 uA, according to the Microchip MCP601 product page. This low-current characteristic makes the amplifier suitable for battery-operated sensing and monitoring systems in which continuous amplifier power can dominate standby consumption. The actual operating current can vary with supply voltage, output state, load, temperature, and device grade, so use the manufacturer datasheet for worst-case design limits. Decoupling capacitors and the selected feedback network should also be checked for their contribution to total system power.
Is MCP601T-I/ST rail-to-rail?
The MCP601T-I/ST is specified with a rail-to-rail output. This allows its output voltage to move closer to the positive and negative supply rails than a traditional fixed-headroom output stage, making the device useful in low-voltage systems with limited signal swing. Rail-to-rail output does not mean that the input common-mode range covers every possible input voltage. The manufacturer datasheet should be used to confirm the input range, maximum output swing, and load-current limits for the intended supply configuration.
What can replace MCP601T-I/ST?
MCP601-I/ST is the verified same-footprint replacement candidate for MCP601T-I/ST because a cross-reference result describes matching terminals, package consistency, and equivalent functional characteristics, and both use an 8-pin TSSOP format. A practical substitution should still be checked for grade, temperature, lifecycle, and sourcing requirements. Cross-brand replacements should not be assumed merely because another amplifier has similar bandwidth. Use the manufacturer pin descriptions and the replacement checklist on this page before approving a drop-in change.
Is MCP601T-I/ST the same as MCP601-I/ST?
MCP601-I/ST is identified as a completely replaceable option for MCP601T-I/ST because their functional characteristics, terminals, and TSSOP packages are consistent. The ordering codes are not necessarily identical, so the exact grade, temperature, and ordering-option requirements should be reviewed before substitution. The verified cross-reference specifically supports MCP601-I/ST as the same-package option. It does not establish that MCP601T-I/OT or MCP601T-I/SN are drop-in choices, because those variants use SOT-23-5 and SOIC-8 packages respectively.
What is the best Microchip equivalent for MCP601T-I/ST?
MCP601-I/ST is the best verified Microchip drop-in candidate for MCP601T-I/ST because the cross-reference describes consistent terminals, package, and functional characteristics. It retains the 8-pin TSSOP footprint and is therefore preferable to MCP601T-I/OT or MCP601T-I/SN for a board designed around the target package. No cross-brand part has been established as a pin-compatible replacement on this page. Confirm the exact suffix requirements and current lifecycle status before using it in a production BOM.
Where can I find the MCP601T-I/ST datasheet and pinout?
The MCP601 family documentation is available from the official Microchip product page at https://www.microchip.com/en-us/product/MCP601, and an Octopart datasheet entry is also available for MCP601T-I/ST. Use the manufacturer MCP601 datasheet's pin-description table when assigning the eight TSSOP pins and when checking the electrical limits for the industrial-temperature suffix. The target is a surface-mount 8-pin TSSOP device. Confirm pin functions against the specific ordering-code table before laying out or modifying a PCB.
When should I choose MCP601T-I/ST over another rail-to-rail op amp?
Choose MCP601T-I/ST when a compact, low-power, single-supply design needs a 2.8 MHz gain-bandwidth product, rail-to-rail output, typical operating current of 230 uA, and an 8-pin TSSOP footprint. It is especially appropriate for sensor conditioning, ADC buffering, and general low-frequency analog signal paths. Choose a different amplifier when the design requires substantially higher bandwidth, lower offset, lower noise, wider input common-mode range, or a different package. Confirm the MCP601 operating limits against the actual signal amplitude, load, and supply voltage.
Is MCP601T-I/ST suitable for sensor signal conditioning?
The MCP601T-I/ST is suitable for many low-frequency sensor signal-conditioning stages because it combines rail-to-rail output, 1 pA listed input bias current, less than 2 mV typical input offset voltage, and a typical operating current of 230 uA. These characteristics help preserve weak sensor signals and reduce the power burden of continuously powered instrumentation. The input source impedance, sensor output range, noise bandwidth, and required accuracy must still be evaluated. High-impedance sensors can expose input bias-current and leakage effects that are not visible from the typical offset specification alone.
MCP601T-I/ST vs MCP601-I/ST: which is better for an existing TSSOP PCB?
MCP601-I/ST is the appropriate verified choice for an existing MCP601T-I/ST TSSOP PCB when the two devices satisfy the required temperature and ordering specifications. The cross-reference describes consistent terminals, package, and functional characteristics, supporting drop-in use without a footprint change. The target MCP601T-I/ST remains the reference choice when its exact suffix, qualification, and lifecycle conditions are required. No resistor, capacitor, or routing changes should be assumed; verify the pin description and electrical limits before production release.
Where to buy MCP601T-I/ST online?
Use the Request a Quote form on this page to request the MCP601T-I/ST, current availability, lead time, and order quantity from XAIPART. The product is an 8-pin TSSOP, single-circuit operational amplifier, so the request should include the required package, quantity, and any date-code or traceability requirements. Commercial terms can change by volume and market conditions, making a current quotation more reliable than a static listing price. For an engineering review, the official Microchip MCP601 family page remains the primary source for technical documentation.
What is the price of MCP601T-I/ST?
Current pricing for MCP601T-I/ST should be obtained through the Request a Quote form on this page. The form can account for the requested quantity and current market conditions without embedding a stale unit price. Include the complete 8-pin TSSOP ordering code MCP601T-I/ST so that the quotation is tied to the correct package and grade. Technical procurement should also check the manufacturer lifecycle status and authorized supply conditions before approving the order, particularly for designs that may require long-term continuity.
What is the lead time for MCP601T-I/ST and is it in stock?
The current lead time and stock position for MCP601T-I/ST should be requested through the Request a Quote form on this page. The manufacturer lists the MCP601 family as a product, and distributor product pages identify the target part, but a distributor search-result headline alone is not a guaranteed allocation commitment. In the quotation request, state the quantity, desired delivery date, and whether alternate date codes or factory packaging are acceptable. This allows procurement to confirm supply against the actual order rather than relying on an unconfirmed search-result stock statement.
Does MCP601T-I/ST meet RoHS, REACH, or automotive qualification requirements?
The RoHS, REACH, lead-free, halogen-free, and conflict-minerals status of MCP601T-I/ST is not stated in the product information used for this page, so those attributes remain unknown rather than being assumed. The industrial-temperature suffix does not by itself establish AEC-Q100 qualification. For an automotive or regulated production design, request the applicable manufacturer declarations and verify the exact ordering code before release. The electrical facts confirmed for the device are its single-circuit rail-to-rail architecture, 2.8 MHz gain-bandwidth product, 230 uA typical operating current, and 8-pin TSSOP package.

Technische Referenzdaten für MCP601T-I/ST – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose MCP601T-I/ST for compact, low-power analog designs that need one rail-to-rail amplifier, a 2.8 MHz gain-bandwidth product, and an 8-pin TSSOP footprint. It is a practical choice for sensor interfaces, ADC input buffering, current-to-voltage conversion, battery-powered instrumentation, and general low-frequency signal amplification. Choose MCP601-I/ST when it satisfies the required temperature and ordering conditions and you want a verified same-package replacement for an existing MCP601T-I/ST board. Do not use MCP601T-I/OT or MCP601T-I/SN as direct PCB replacements because their SOT-23-5 and SOIC-8 packages differ from the TSSOP target. For designs requiring substantially lower offset, lower noise, higher bandwidth, wider common-mode range, or automotive qualification, compare those requirements against the MCP601 family limits and select a more specialized amplifier.

Vergleich mit Alternativen

Parameter Dieses Produkt MCP601-I/ST
Package 8-pin TSSOP 8-pin TSSOP
Brand Microchip Technology Microchip Technology
Number of Circuits 1 circuit 1 circuit
Amplifier Type General-purpose operational amplifier General-purpose operational amplifier
Drop-In Status Reference device Verified same-package replacement with consistent terminals and functional characteristics

Wichtigste Unterscheidungsmerkmale

  • Low-power CMOS operation with a verified same-package replacement path (vs. MCP601-I/ST)
  • Rail-to-rail output in a compact 8-pin TSSOP package (vs. MCP601T-I/OT)
  • Low-power general-purpose signal conditioning (vs. MCP601T-I/SN)

Designhinweise

Place the input, output, and supply connections so that the amplifier is not forced to carry long high-impedance traces. Connect the decoupling capacitor directly between the supply and ground pins, keep the feedback components close to their corresponding pins, and provide a low-impedance ground return. In an ADC buffer or sensor stage, route the sensitive input away from switching nodes and regulators. These layout practices are especially important because the listed 1 pA input bias current is small enough for PCB leakage and contamination effects to become significant.

Check closed-loop bandwidth using the selected feedback resistors and the intended load rather than relying only on the 2.8 MHz gain-bandwidth product. The listed 2.3 V/us slew rate also limits large-signal response for fast, low-amplitude waveforms. For capacitance at the amplifier input, as commonly encountered with photodiodes or long sensor cables, evaluate stability or add compensation according to the manufacturer guidance. Confirm the input common-mode range and output swing throughout startup, shutdown, and supply variation.

Design the power path for the minimum operating voltage of 2.7 V while including the 6 V maximum supply limit as a hard design boundary. The 230 uA figure describes typical amplifier operating current and should not be treated as the entire system demand. Estimate total current using the supply voltage, amplifier state, load, and attached circuits. Where the amplifier operates continuously, confirm that its dissipation remains within the package's thermal limits and that the regulator can support startup current without pulling the supply outside the amplifier's valid operating range.

Do not substitute MCP601T-I/OT or MCP601T-I/SN directly for MCP601T-I/ST on the same PCB: the related devices use SOT-23-5 and SOIC-8 packages rather than the target 8-pin TSSOP footprint. MCP601-I/ST is the verified same-package candidate because the cross-reference identifies consistent terminals, package, and functional characteristics. Before substitution, confirm the exact temperature, qualification, lifecycle, and ordering-code requirements and compare the manufacturer pin descriptions.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

Compliance declarations and AEC-Q100 qualification status are not stated in the available product information and must be confirmed for the exact ordering code.

Ähnliche Suchanfragen

mcp601t datasheet MCP601T-I/ST datasheet MCP601T-I/ST datasheet pdf MCP601T-I/ST pinout MCP601T-I/ST equivalent MCP601T-I/ST replacement MCP601T-I/ST cross reference MCP601T-I/ST application circuit MCP601T-I/ST sensor conditioning Microchip MCP601T-I/ST MCP601T-I/ST TSSOP pinout MCP601T-I/ST vs MCP601-I/ST MCP601T-I/ST price MCP601T-I/ST stock

Verwandte Bauteile & Begriffe

Microchip Technology MCP601T-I/ST MCP601 MCP601-I/ST MCP601T-I/OT MCP601T-I/SN Operational amplifier Op amp Voltage-feedback amplifier Analog signal conditioning Rail-to-rail output Advanced CMOS 2.8 MHz gain-bandwidth product 230 uA typical operating current 1 pA input bias current 2.3 V/us slew rate 8-pin TSSOP TSSOP package family Surface mount SMD Low-dropout regulator LDO Low-dropout regulator LDO Low-dropout regulator LDO
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen