MCP601T-I/ST - 2.8MHz Rail-to-Rail CMOS Op Amp | Microchip
MPN: MCP601T-I/ST ✓ 啟用中MCP601T-I/ST 概覽
An operational amplifier, or op amp, is an analog integrated circuit that uses high-gain differential feedback to amplify a voltage difference. It belongs to the amplifier IC hierarchy: operational amplifier -> voltage-feedback amplifier -> analog signal conditioning -> semiconductor. The rail-to-rail output architecture allows the output to approach the available supply rails more closely than a conventional fixed-headroom output stage, which is valuable in compact systems that require a usable output swing from a low-voltage supply.
The MCP601T-I/ST combines a 2.8 MHz gain-bandwidth product with low typical operating current of 230 uA. Its listed typical input offset voltage is below 2 mV, and the LCSC product listing identifies a 1 pA input bias-current figure. A slew rate of 2.3 V/us is also listed for the device. These characteristics place it between general-purpose signal amplification and low-power acquisition applications where low quiescent consumption and rail-to-rail output capability are more important than very high bandwidth.
The MCP601 uses advanced CMOS technology to support low-power operation and high input impedance. Rail-to-rail output capability is particularly useful for buffer, transducer, and sensor-interface stages that operate near either supply rail. Designers should still account for input common-mode range, output swing, noise, stability with the selected feedback network, and decoupling when applying the amplifier outside its simplest voltage-follower configuration. The exact MCP601T-I/ST ordering suffix identifies the industrial temperature and TSSOP packaging option.
Typical uses include low-power sensor conditioning, battery-powered instrumentation, ADC input buffering, current-to-voltage conversion with a feedback resistor, general signal amplification, and unity-gain buffers. The 8-TSSOP package supports compact PCB layouts, while the 230 uA typical operating current helps reduce the energy burden in continuously powered systems. Because the listed 2.8 MHz bandwidth is modest compared with high-speed amplifiers, the MCP601T-I/ST is best suited to low- and intermediate-frequency signal paths rather than wideband pulse or video amplification.
For a new design, use the manufacturer datasheet pin description and typical-application circuit when assigning pins and compensation or feedback values. Keep input and output nodes short, provide local supply bypassing, and verify the input common-mode and output-voltage limits against the actual operating rail. The Request a Quote form on this page provides current commercial availability, lead-time, and order information without embedding a static price.
This product page combines manufacturer specifications, package information, practical design guidance, drop-in replacement analysis, and a parameter comparison for the MCP601T-I/ST. It also distinguishes the verified TSSOP option from other MCP601 package and ordering variants, helping engineers identify a suitable replacement before committing to a PCB revision.
直接替換替代品,適用於 MCP601T-I/ST — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MCP601T-I/ST (相同外形與佔位) — 差異在於 Number of Circuits, Package, Amplifier Type, Supply Voltage Range, Technology.
MCP601-I/ST
✅ 直接替換聯絡詢價
查看資料表 →MCP601T-I/ST 最大額定值與電氣特性
| Number of Circuits | 1 circuit |
| Product Type | General-purpose operational amplifier |
| Gain-Bandwidth Product | 2.8 MHz |
| Typical Operating Current | 230 uA |
| Typical Input Offset Voltage | <2 mV |
| Input Bias Current | 1 pA |
| Slew Rate | 2.3 V/us |
| 輸出類型 | Rail-to-rail |
| Technology | Advanced CMOS |
| Minimum Supply Voltage | 2.7 V |
| Maximum Supply Voltage | 6 V |
| 封裝 | 8-pin TSSOP |
| 安裝類型 | Surface mount |
MCP601T-I/ST 8-pin tssop 腳位配置指南
MCP601T-I/ST(8-pin tssop 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: MCP601T-I/ST.
請參閱 資料表 以查看完整腳位配置。
典型應用
MCP601T-I/ST 適用於 6 應用s: Low-Power Sensor Conditioning, Battery-Powered Instrumentation, ADC Input Buffering, Current-to-Voltage Conversion, General Signal Amplification, Precision Analog Signal Conditioning.
Low-Power Sensor Conditioning
The MCP601T-I/ST fits low-power sensor conditioning because it combines a listed 1 pA input bias current with less than 2 mV typical input offset voltage and a 2.8 MHz gain-bandwidth product. Place the amplifier in a non-inverting or differential stage when the sensor output permits, then use the feedback network to establish the required gain while preserving sensor bandwidth. Its 230 uA typical operating current is useful in continuously powered instrumentation. The key trade-off is that the 2.8 MHz gain-bandwidth product limits high-gain operation at higher frequencies, so verify the closed-loop response and noise bandwidth before finalizing the sensor interface.
推薦
Battery-Powered Instrumentation
The MCP601T-I/ST is appropriate for battery-powered instrumentation that requires signal amplification without a continuously high-power analog stage. Its 230 uA typical operating current and 2.7 V minimum supply voltage support compact low-voltage systems, while the rail-to-rail output provides useful signal swing near the supply limits. The amplifier can buffer a transducer or condition a control signal before an ADC input. Because amplifier current is only one part of total consumption, include sensor, ADC, reference, and regulator consumption in the system budget, and check output loading and input common-mode limits at the lowest operating voltage.
推薦
ADC Input Buffering
The MCP601T-I/ST can serve as an ADC input buffer when the converter requires a low-impedance drive and the source signal does not need the bandwidth of a high-speed amplifier. Its listed 1 pA input bias current reduces loading on high-impedance sources, and the less-than-2 mV typical offset can help preserve low-level signal accuracy. Use a unity-gain follower or the required gain configuration and place the amplifier close to the ADC input to minimize trace pickup. Validate settling time, capacitive loading, output swing, and the ADC's acquisition window, since the 2.8 MHz gain-bandwidth product does not guarantee fast settling for every gain and load.
推薦
Current-to-Voltage Conversion
The MCP601T-I/ST can convert a small current into a voltage in a transimpedance amplifier used with photodiodes, sensors, or current-output transducers. The listed 1 pA input bias current is a useful starting point for high-impedance feedback arrangements, while rail-to-rail output helps use more of the available signal range. Choose the feedback resistor and compensation capacitance from the source capacitance and target bandwidth requirements. Verify stability, input bias effects, noise, and output-current capability because a general-purpose 2.8 MHz amplifier is intended for modest-bandwidth precision functions rather than very fast photodiode transimpedance designs.
推薦
General Signal Amplification
The MCP601T-I/ST is suitable for general signal amplification in small analog boards that need a single amplifier with rail-to-rail output. Its 2.8 MHz gain-bandwidth product supports low-frequency and moderate-bandwidth waveforms, while the 230 uA typical operating current suits compact and portable equipment. Configure the closed-loop gain with conventional feedback resistors and verify the resulting bandwidth, output swing, and distortion. The 8-pin TSSOP package permits a small footprint, but decoupling and grounding still require careful layout. For audio, measurement, or industrial channels requiring lower noise or narrower offset, compare the measured requirements against the amplifier's full datasheet limits.
推薦
Precision Analog Signal Conditioning
The MCP601T-I/ST can condition low-level analog signals in measurement and control systems where rail-to-rail output and low typical operating current are useful. Its typical input offset voltage below 2 mV and 2.8 MHz gain-bandwidth product are meaningful for many precision, low-to-moderate-frequency paths. The amplifier should be evaluated for offset drift, noise, common-mode rejection, and gain error under the required temperature range rather than relying only on typical figures. Use a clean reference, stable feedback resistors, local bypass capacitors, and grounded return paths. For instrumentation requiring gain error or noise substantially below the general-purpose MCP601 performance, select a precision amplifier instead.
推薦
推薦產品摘要
工程參考資料,適用於 MCP601T-I/ST — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP601-I/ST |
|---|---|---|
| Package | 8-pin TSSOP | 8-pin TSSOP |
| Brand | Microchip Technology | Microchip Technology |
| Number of Circuits | 1 circuit | 1 circuit |
| Amplifier Type | General-purpose operational amplifier | General-purpose operational amplifier |
| Drop-In Status | Reference device | Verified same-package replacement with consistent terminals and functional characteristics |
主要差異化特點
- Low-power CMOS operation with a verified same-package replacement path (對比MCP601-I/ST)
- Rail-to-rail output in a compact 8-pin TSSOP package (對比MCP601T-I/OT)
- Low-power general-purpose signal conditioning (對比MCP601T-I/SN)
設計說明
Place the input, output, and supply connections so that the amplifier is not forced to carry long high-impedance traces. Connect the decoupling capacitor directly between the supply and ground pins, keep the feedback components close to their corresponding pins, and provide a low-impedance ground return. In an ADC buffer or sensor stage, route the sensitive input away from switching nodes and regulators. These layout practices are especially important because the listed 1 pA input bias current is small enough for PCB leakage and contamination effects to become significant.
Check closed-loop bandwidth using the selected feedback resistors and the intended load rather than relying only on the 2.8 MHz gain-bandwidth product. The listed 2.3 V/us slew rate also limits large-signal response for fast, low-amplitude waveforms. For capacitance at the amplifier input, as commonly encountered with photodiodes or long sensor cables, evaluate stability or add compensation according to the manufacturer guidance. Confirm the input common-mode range and output swing throughout startup, shutdown, and supply variation.
Design the power path for the minimum operating voltage of 2.7 V while including the 6 V maximum supply limit as a hard design boundary. The 230 uA figure describes typical amplifier operating current and should not be treated as the entire system demand. Estimate total current using the supply voltage, amplifier state, load, and attached circuits. Where the amplifier operates continuously, confirm that its dissipation remains within the package's thermal limits and that the regulator can support startup current without pulling the supply outside the amplifier's valid operating range.
Do not substitute MCP601T-I/OT or MCP601T-I/SN directly for MCP601T-I/ST on the same PCB: the related devices use SOT-23-5 and SOIC-8 packages rather than the target 8-pin TSSOP footprint. MCP601-I/ST is the verified same-package candidate because the cross-reference identifies consistent terminals, package, and functional characteristics. Before substitution, confirm the exact temperature, qualification, lifecycle, and ordering-code requirements and compare the manufacturer pin descriptions.
合規資訊
Compliance declarations and AEC-Q100 qualification status are not stated in the available product information and must be confirmed for the exact ordering code.