MCP6064-E/ST - Quad 1.8V Precision R-R Op Amp | Microchip
Teilenummer: MCP6064-E/ST ✓ AktivMCP6064-E/ST Übersicht
An operational amplifier is an analog building block used to amplify, buffer, filter, or compare small voltage signals. The MCP6064 belongs to the operational-amplifier hierarchy within analog ICs and amplifier ICs. Rail-to-rail input operation allows the amplifier to process signals close to either supply rail, while rail-to-rail output improves dynamic range in low-voltage systems. Its unity-gain stability permits use as a voltage follower without external compensation.
The MCP6064-E/ST provides four amplifiers in one package, reducing board area compared with four separate single amplifiers. Key characteristics include maximum input offset voltage of ±150 µV, typical gain-bandwidth product of 730 kHz, and low quiescent current of 60 µA per amplifier. Rail-to-rail input and output operation supports single-supply systems operating from 1.8 V, while the listed 6 V maximum rating provides compatibility with conventional 3.3 V and 5 V analog rails.
Each amplifier in the quad package is designed around CMOS analog circuitry optimized for precision and low power. A 730 kHz gain-bandwidth product supports moderate-bandwidth gain and filtering stages without requiring a high-speed, high-power amplifier. Unity-gain stability is particularly useful for ADC drivers, sensor buffers, and active-filter inputs. Because four amplifiers share one package, engineers should account for common supply current, thermal behavior, and package-level decoupling when planning the complete analog front end.
Typical uses include battery-powered sensor interfaces, precision current measurement, low-frequency active filters, audio preamplification, industrial instrumentation, and automotive sensing. The 14-pin TSSOP outline is compact but requires careful handling of fine-pitch leads. In a 3.3 V or 5 V design, confirm signal amplitudes, output-load limits, stability, and the amplifier's operating range before finalizing the gain and filtering network.
Decouple the supply pins with a short-path ceramic capacitor and keep feedback components close to their associated amplifier inputs and outputs. Avoid long traces around high-impedance nodes because input bias current and parasitic capacitance can shift offset and degrade stability. For applications requiring the lowest input error, use the maximum input offset voltage rather than the typical value when setting system tolerances.
This page combines manufacturer-family specifications, package information, application guidance, comparison criteria, and practical design notes. It also identifies which proposed replacements have a defensible 14-TSSOP drop-in basis and which characteristics still require independent engineering review before schematic approval.
Drop-in-Alternativen für MCP6064-E/ST – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
MCP6064T-E/ST
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MCP6004-I/ST
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
LMV324IPT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MCP6064-E/ST Grenzwerte & elektrische Eigenschaften
| Amplifier Count | 4 amplifiers |
| Minimum Single-Supply Voltage | 1.8 V |
| Maximum Supply Voltage | 6 V |
| Input Offset Voltage | ±150 µV maximum |
| Gain-Bandwidth Product | 730 kHz typical |
| Ruhestrom | 60 µA per amplifier typical |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Gain Stability | Unity-gain stable |
| Process Technology | CMOS |
| Gehäuse | 14-pin TSSOP |
| Montageart | Surface mount |
| Temperature Grade | Extended-temperature grade |
| Automotive Qualification | AEC-Q100 qualified |
| Supplier Tube Description | 14-pin TSSOP tube |
| Product Type | Precision CMOS operational amplifier |
MCP6064-E/ST 14-pin tssop Pinbelegungsleitfaden
Pinbelegung für MCP6064-E/ST (14-pin tssop-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für MCP6064-E/ST.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
MCP6064-E/ST ist geeignet für 6 Anwendungs: Battery-Powered Sensor Interfaces, Precision Current Measurement, Low-Frequency Active Filters, Industrial Instrumentation, Audio and Microphone Preamplification, Automotive and Vehicle Sensing.
Battery-Powered Sensor Interfaces
The MCP6064-E/ST fits low-power sensor front ends because each amplifier operates from a supply as low as 1.8 V and consumes 60 µA typical quiescent current. Rail-to-rail input operation preserves signal range when a sensor output approaches either supply rail, an important consideration for resistive dividers and low-voltage current sensors. Four amplifiers in one 14-pin TSSOP can provide input buffering, gain, active filtering, and an output driver without requiring four separate packages. Keep high-impedance sensor connections short and evaluate total quiescent current across all four channels when calculating battery life.
Empfohlen
Precision Current Measurement
The MCP6064-E/ST is suitable for amplifying the small differential voltage generated by a shunt or current-sense resistor in a precision measurement channel. Its maximum input offset voltage of ±150 µV helps limit error near the measurement floor, while the 730 kHz typical gain-bandwidth product is adequate for moderate-bandwidth current loops and control signals. Rail-to-rail input and output operation supports low-voltage instrumentation. The design should still budget resistor tolerance, amplifier input bias current, Kelvin routing, and gain error; the 14-pin TSSOP package does not eliminate analog-layout sensitivity.
Empfohlen
Low-Frequency Active Filters
The unity-gain-stable MCP6064-E/ST can implement low-frequency active-filter stages where a 730 kHz gain-bandwidth product provides adequate closed-loop bandwidth. The quad package allows a second-order filter to use one section and leaves three channels available for gain, buffering, or offset conditioning. Its low 60 µA-per-amplifier quiescent current is beneficial in portable measurement equipment. Select resistor and capacitor values with phase-margin and noise considerations, and simulate the complete filter with the intended load because parasitic capacitance and rail-to-rail transition behavior can influence the final response.
Empfohlen
Industrial Instrumentation
The MCP6064-E/ST can condition low-level industrial sensor signals in compact control and monitoring modules. Its rail-to-rail I/O operation allows useful signal coverage in 3.3 V and 5 V systems, while the maximum input offset voltage of ±150 µV supports precision-oriented measurement chains. The four integrated channels reduce board area for amplifier, buffer, and comparator stages. For industrial equipment, evaluate electromagnetic interference, temperature margin, supply sequencing, and grounding. The TSSOP outline is compact, so assembly processes must provide suitable fine-pitch handling and adequate copper routing around sensitive inputs.
Empfohlen
Audio and Microphone Preamplification
The MCP6064-E/ST can provide low-level preamplification and buffering in compact audio or microphone modules. Rail-to-rail input operation is useful when the available headroom around the bias point is limited, and four channels allow microphone, headphone, auxiliary, or line-processing functions to share a compact package. The 730 kHz typical gain-bandwidth product supports low-to-moderate audio bandwidth rather than high-frequency audiophile chains. Verify input-noise performance, maximum output swing, capacitive-load stability, and channel-to-channel matching against the microphone impedance and amplifier gain used in the design.
Empfohlen
Automotive and Vehicle Sensing
The MCP6064-E/ST is identified in automotive-grade distributor records with AEC-Q100 qualification, making it a candidate for low-voltage vehicle sensing and control interfaces. Its 1.8 V minimum supply and 60 µA typical quiescent current per amplifier support compact electronics operating close to battery rails, while rail-to-rail I/O improves usable signal range. Confirm the exact qualification level, temperature grade, production status, and AEC-Q100-related part documentation for the production program. Transient protection, load-dump exposure, ground-offset behavior, and EMI requirements must also be handled at the system level.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für MCP6064-E/ST – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | MCP6064T-E/ST | MCP6004-I/ST | LMV324IPT |
|---|---|---|---|---|
| Package | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Texas Instruments |
| Amplifier Count | 4 | 4 | 4 | 4 |
Wichtigste Unterscheidungsmerkmale
- Lower minimum operating supply (vs. LMV324IPT)
- Rail-to-rail signal handling at low supply voltage (vs. LMV324IPT)
- Identical electrical family with production packing flexibility (vs. MCP6064T-E/ST)
Designhinweise
Place the supply bypass capacitor directly between the supply and ground pins, with the shortest possible traces and a ground connection that does not share a long return path with sensor signals. For a quad amplifier, follow the manufacturer pinout rather than assuming that all four channels are grouped identically. Keep feedback resistors close to their associated output and input pins, and route high-impedance inputs away from switching nodes, inductors, and the exposed underside of adjacent circuitry.
Unity-gain stability does not make every feedback network stable in practice. Check the gain-versus-frequency response with the intended source impedance, load capacitance, trace capacitance, and supply decoupling. Add an isolation resistor between the amplifier output and a difficult capacitive load when necessary, and keep the resistor close to the output pin. Verify rail-to-rail transition behavior in simulation or on hardware because crossover distortion can matter in low-signal-level instrumentation.
Do not treat the 730 kHz typical gain-bandwidth product as a guaranteed small-signal bandwidth at every closed-loop gain or output voltage. Use the manufacturer gain-bandwidth and phase-margin information to select a stable closed-loop gain, especially near unity gain. Also avoid assuming that the extended-temperature designation permits unrestricted automotive use. Confirm the exact AEC-Q100 qualification, temperature limits, and production-test requirements for the deployed operating environment.
Compliance-Informationen
The MCP6064-E/ST product listing identifies the device as AEC-Q100 automotive qualified. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer product documentation.