OPA180ID - 36V Zero-Drift Precision Op Amp | Texas Instruments
Teilenummer: OPA180ID ✓ AktivOPA180ID Übersicht
An operational amplifier is a voltage-feedback analog integrated circuit that amplifies the difference between two input voltages. Its role in the power-management and signal-chain hierarchy is foundational: sensor outputs, currents, and reference voltages are conditioned by an op amp before conversion by an ADC or use by a control loop. The OPA180 family belongs to the zero-drift amplifier class, combining continuous-time signal handling with unusually low input-offset behavior.
Key features include a typical input offset of 75 uV, 0.1 uV/°C temperature drift, and rail-to-rail output swing within 18 mV of the supply rails. According to the Texas Instruments OPA180 datasheet, the amplifier also provides high input impedance and low-noise operation. These characteristics make it suitable for bridge and thermocouple front ends, current-sense amplifiers, precision filters, and high-impedance sensor interfaces.
The OPA180ID uses proprietary zero-drift techniques to suppress offset variation over time and temperature. Its continuous operation avoids the chopping artifacts associated with some chopped amplifiers while delivering low drift for dc-accurate measurements. The 36 V supply capability also permits operation from higher-voltage industrial rails, although the input common-mode range must remain within the device's specified limits for linear operation.
Typical uses include low-frequency precision measurement, load-cell and pressure-sensor amplification, analog sensor conditioning, and active filtering. In an instrumentation design, the amplifier converts a millivolt-scale differential input into a voltage suitable for an ADC, while its low offset prevents errors from being mistaken for real sensor changes. The 8-pin SOIC package also simplifies assembly on conventional through-hole-compatible PCB layouts.
When designing around the OPA180ID, verify the input common-mode range at the actual supply voltage and supply decoupling capacitance. Zero-drift performance improves long-term accuracy, but input bias current, noise, bandwidth, and settling behavior still determine practical performance in fast or high-impedance systems. The 2 MHz gain-bandwidth product favors low-frequency precision rather than wideband signal handling.
This page combines manufacturer specifications, package details, drop-in replacement guidance, application design notes, and a parameter comparison to support component selection and PCB implementation decisions beyond the basic catalog listing.
Drop-in-Alternativen für OPA180ID – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit OPA180ID (gleiche Bauform und Footprint) – abweichend in Package, Amplifier Type, Gain-Bandwidth Product, Input Offset Voltage, Input Offset Voltage Drift.
OPA182ID
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
OPA189ID
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →OPA191ID
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →OPA280ID
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
OPA380ID
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
OPA180ID Grenzwerte & elektrische Eigenschaften
| Amplifier Type | Single zero-drift operational amplifier |
| Number of Circuits | 1 circuit |
| Maximum Supply Voltage | 36 V |
| Input Offset Voltage | 75 uV typical |
| Input Offset Voltage Drift | 0.1 uV/°C |
| Gain-Bandwidth Product | 2 MHz |
| Output Swing | Rail-to-rail, within 18 mV of the rails |
| Input Impedance | High impedance |
| Input Noise | Low noise |
| Offset Drift | Near zero over time and temperature |
| Gehäuse | 8-pin SOIC, 0.154 inch body width, 3.90 mm wide |
| Montageart | Surface mount |
OPA180ID Pin-Konfiguration
| Pin 1 | NC — Not connected (per datasheet) |
| Pin 2 | IN- — Inverting input |
| Pin 3 | IN+ — Non-inverting input |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | NC — Not connected (per datasheet) |
| Pin 6 | OUT — Output |
| Pin 7 | V+ — Positive supply connection |
| Pin 8 | NC — Not connected (per datasheet) |
Typische Anwendungen
OPA180ID ist geeignet für 6 Anwendungs: Load-Cell and Strain-Gauge Amplification, Precision Current-Sense Amplification, Low-Level Sensor Signal Conditioning, Precision Active Filtering, High-Impedance Instrumentation Front Ends, Industrial Process-Control Loops.
Load-Cell and Strain-Gauge Amplification
The OPA180ID fits low-level differential bridge measurements because its 75 uV typical input offset and 0.1 uV/°C drift limit temperature-dependent errors in strain-gauge amplifiers. Place the amplifier directly across the bridge output and use matched gain resistors to preserve common-mode rejection. With a 2 MHz gain-bandwidth product, it supports low-to-moderate bandwidth measurements rather than high-speed transient sensing. Confirm the actual bridge excitation level, common-mode voltage, and input-bias-current requirements before finalizing the gain network.
Empfohlen
Precision Current-Sense Amplification
The OPA180ID is appropriate for amplifying the small differential voltage produced across a shunt resistor. Its low offset of 75 uV and drift of 0.1 uV/°C help prevent the amplifier from adding a temperature-dependent error to the measured current. The rail-to-rail output, which operates within 18 mV of the rails, also provides useful headroom when the shunt signal occupies much of the available input range. Bias-current effects, Kelvin shunt routing, and the common-mode voltage at the input pins remain critical layout considerations.
Empfohlen
Low-Level Sensor Signal Conditioning
For pressure, temperature, and electrochemical sensors that produce millivolt-scale signals, the OPA180ID conditions the differential output with low offset and drift. Its high input impedance reduces loading on the sensor, while the 36 V supply capability supports industrial systems with higher rail voltages. The amplifier should operate within its specified input common-mode range, and the selected gain must remain consistent with the 2 MHz gain-bandwidth product. Filtering should be placed close to the amplifier pins to minimize interference pickup.
Empfohlen
Precision Active Filtering
The OPA180ID can implement low-frequency active filters where drift and dc accuracy are important, such as anti-alias filters, low-pass stages, and signal-conditioning networks. Its 2 MHz gain-bandwidth product provides a practical upper limit for closed-loop gain and stability calculations. A low-frequency filter also benefits from the low offset because filter output errors otherwise accumulate through the signal chain. Confirm noise gain, capacitive loading, and settling requirements for each filter stage, and place feedback components to minimize parasitic coupling.
Empfohlen
High-Impedance Instrumentation Front Ends
The OPA180ID suits high-impedance instrumentation inputs because it combines high input impedance with near-zero offset drift. It can amplify weak sensor signals while reducing dc errors that would otherwise be integrated by the following measurement stage. Because input bias current still creates errors with very high source impedances, keep source impedances balanced and use guarding where necessary. The 36 V maximum supply supports higher-voltage industrial systems, but signal levels must remain inside the linear common-mode range.
Empfohlen
Industrial Process-Control Loops
The OPA180ID can condition error and feedback signals in slow industrial control loops where temperature stability is valuable. Its 75 uV typical offset and 0.1 uV/°C drift reduce measurement shifts as equipment temperature changes. The 36 V supply rating accommodates higher industrial rails, while the 2 MHz gain-bandwidth product is sufficient for many process-control bandwidths. Check the common-mode range, output load, noise-gain stability, and isolation requirements before integrating the amplifier near an analog-to-digital converter.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für OPA180ID – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | OPA182ID | OPA189ID | OPA191ID | OPA280ID | OPA380ID |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Maximum Supply Voltage | 36 V | 36 V | 36 V | 36 V | 36 V | 36 V |
| Gain-Bandwidth Product | 2 MHz | Approximately 2.5 MHz | Approximately 1.8 MHz | Approximately 1.8 MHz | Approximately 1.6 MHz | Approximately 2.5 MHz |
| Number of Channels | 1 | 1 | 1 | 1 | 1 | 1 |
Wichtigste Unterscheidungsmerkmale
- Combines a 2 MHz gain-bandwidth product with very low offset drift (vs. OPA280ID)
- Near-zero 0.1 uV/°C offset drift supports precision temperature-stable measurements (vs. OPA182ID)
- Combines 36 V supply capability with low-noise precision operation (vs. OPA191ID)
Designhinweise
Do not treat the rail-to-rail output specification as a rail-to-rail input specification. Check the operating common-mode range against the actual signal and supply voltages in the manufacturer datasheet. Also verify the output load because the 18 mV swing limit is measured under specified conditions. For sensor signals, keep the input pair short, balanced, and away from switching nodes and digital return currents.
Place the input, output, and feedback components close to the OPA180ID pins to minimize parasitic capacitance and feedback-loop length. Route the two input traces as a closely matched pair, connect the negative supply to a quiet return plane, and avoid routing them beside switching inductors or high-current traces. Use the pin-description table in the manufacturer datasheet when assigning the no-connect positions.
The OPA180ID's 2 MHz gain-bandwidth product requires careful noise-gain analysis at high closed-loop gains. Confirm that capacitive loading will not make the amplifier unstable, and place feedback resistors close to the output and input pins. For low-frequency precision applications, use matched resistor networks and evaluate input bias current, noise, and settling separately rather than relying on offset voltage alone.
Estimated: power dissipation depends on the actual supply voltage, output voltage, load current, and ambient temperature. At 36 V with the output near mid-supply and 1 mA of load, static dissipation is approximately 36 V × 1 mA = 36 mW, excluding internal bias current. The SOIC-8 thermal resistance must be taken from the package data for the actual PCB copper and still-air conditions before defining the maximum allowable temperature rise.
Compliance-Informationen
Compliance declarations should be confirmed against the current manufacturer product page and orderable-part documentation for the exact OPA180ID package code.