OPA336UA - 5.5V Micropower RRIO Op Amp | Texas Instruments
Teilenummer: OPA336UA ✓ AktivOPA336UA Übersicht
An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify the voltage difference between its two inputs. The OPA336 belongs to the microAmplifier family of CMOS op amps, a subcategory of analog amplifiers and linear integrated circuits. Its rail-to-rail output can operate close to both supply rails, while its negative-supply common-mode capability makes single-supply operation practical when input signals remain near ground.
Key features include a maximum offset voltage of 125 µV, typical input bias current of 1 pA, and open-loop gain of 115 dB. The 20 µA quiescent current per amplifier supports battery-powered equipment by limiting static power demand. According to the manufacturer information, output swing reaches within 3 mV of the supply rails with a 100 kΩ load, giving designers useful headroom when operating from a 5.5 V supply.
The OPA336 uses a CMOS voltage-feedback architecture and belongs to a family that includes single, dual, and quad versions with matching core specifications. Its 100 kHz bandwidth is sufficient for low-frequency sensor conditioning, current measurement, instrumentation, and general signal amplification. The 1 pA input bias current is especially useful with high-impedance sources, where input leakage can otherwise create substantial voltage errors.
Typical uses include battery-powered biomedical instrumentation, portable measurement systems, sensor interfaces, low-current monitoring circuits, and portable audio equipment. It can also buffer slow sensor outputs or provide gain ahead of an ADC. Designers should account for its limited bandwidth when processing higher-frequency signals and verify stability with the intended source impedance, load, and feedback network.
For single-supply designs, connect the negative supply pin to ground and bias inputs into the usable common-mode range. Place input and feedback components close to the device, avoid long high-impedance traces, and check output swing at the minimum available output voltage. The 8-pin SOIC package supports conventional surface-mount assembly and is available in tube packaging.
This page combines the manufacturer specifications with pin-level implementation guidance, practical application positioning, and a compatibility-focused comparison. It helps engineers distinguish the OPA336UA from adjacent family members and choose among alternative amplifier approaches without overlooking bandwidth, offset, quiescent-current, supply-voltage, or package constraints.
Drop-in-Alternativen für OPA336UA – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit OPA336UA (gleiche Bauform und Footprint) – abweichend in Package, Open-Loop Gain, Product Type, Maximum Input Offset Voltage, Mounting Type.
Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.
Alternativen anfordernOPA336UA Grenzwerte & elektrische Eigenschaften
| Product Type | Single operational amplifier |
| Architecture | CMOS voltage-feedback |
| Number of Amplifiers | 1 amplifier |
| Supply Type | Single supply |
| Minimum Operating Supply Voltage | 2.1 V |
| Maximum Operating Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 100 kHz |
| Typical Quiescent Current | 20 µA per amplifier |
| Maximum Input Offset Voltage | 125 µV |
| Typical Input Bias Current | 1 pA |
| Open-Loop Gain | 115 dB |
| Output Swing | Within 3 mV of the supply rails at 100 kΩ load |
| Common-Mode Input Range | Extends to the negative supply |
| Ausgangstyp | Rail-to-rail output |
| Gehäuse | 8-pin SOIC |
OPA336UA Pin-Konfiguration
| Pin 1 | NC — Not connected |
| Pin 2 | IN- — Inverting input |
| Pin 3 | IN+ — Non-inverting input |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | NC — Not connected |
| Pin 6 | OUT — Output |
| Pin 7 | V+ — Positive supply connection |
| Pin 8 | NC — Not connected |
Typische Anwendungen
OPA336UA ist geeignet für 6 Anwendungs: Battery-Powered Sensor Conditioning, Portable Medical Instrumentation, Portable Audio Signal Buffer, Low-Current Monitoring Circuit, Industrial Data Acquisition, IoT Environmental Sensor Node.
Battery-Powered Sensor Conditioning
OPA336UA fits low-power sensor front ends because it operates from 2.1 V to 5.5 V and draws approximately 20 µA of quiescent current per amplifier. Place it in a non-inverting or differential gain stage ahead of an ADC, using its 125 µV maximum offset and 1 pA typical input bias current to limit input-referred error. The 100 kHz bandwidth is suitable for temperature, pressure, and chemical sensors with slow bandwidth requirements. Keep traces short and guard high-impedance input nodes to prevent leakage and interference from raising the effective error floor.
Empfohlen
Portable Medical Instrumentation
The low quiescent current of OPA336UA makes it useful in portable medical and diagnostic equipment where battery life constrains every stage. Its single-supply operation begins at 2.1 V, while the common-mode range extends to the negative supply and the output approaches the positive rail. These properties allow the amplifier to process small sensor signals without adding a negative rail. The 100 kHz bandwidth suits low-frequency physiological and diagnostic signals; higher-frequency stages may require a wider-bandwidth amplifier. Confirm leakage, noise, and clinical validation requirements for the finished instrument.
Empfohlen
Portable Audio Signal Buffer
OPA336UA can buffer low-level audio or control signals in portable equipment when the required bandwidth is well below 100 kHz. Its rail-to-rail output provides useful swing on a single supply, and output reaches within 3 mV of the supply rails at a 100 kΩ load. The approximately 20 µA quiescent current reduces the static burden on a battery, while the 1 pA typical input bias current is favorable for high-impedance source networks. Check output drive into the actual headphone, transducer, or codec input and verify capacitive-load stability.
Empfohlen
Low-Current Monitoring Circuit
OPA336UA is suitable for amplifying small signals in low-current monitoring systems because its 1 pA typical input bias current limits the error introduced by high source impedance. Place it in a transimpedance or differential stage where the measured signal bandwidth remains within the 100 kHz gain-bandwidth product. The 125 µV maximum offset voltage is particularly relevant to low-level measurements, while the 20 µA typical quiescent current keeps demand low. Include input protection, verify noise performance, and account for the amplifier’s input and output limits across temperature.
Empfohlen
Industrial Data Acquisition
OPA336UA can serve as the input amplifier in a compact industrial data-acquisition channel when the measured bandwidth is low. Its 5.5 V maximum supply and 2.1 V minimum operating voltage support both nominal 3.3 V and 5 V rails, and rail-to-rail output increases usable signal span. The 100 kHz closed-loop bandwidth is suitable for many temperature, pressure, and level signals but not for high-speed vibration sampling. Use proper guarding around sensitive inputs, maintain a stable reference path, and verify the complete analog chain for gain error and channel-to-channel matching.
Empfohlen
IoT Environmental Sensor Node
OPA336UA fits IoT environmental sensor nodes where a small, low-power amplifier conditions outputs from resistive or semiconductor sensors before digitization. Operating from 2.1 V to 5.5 V supports compact energy-harvesting and battery-powered systems, and 20 µA typical quiescent current minimizes standby demand. Its 1 pA typical input bias current is beneficial when sensors have high output impedance, while rail-to-rail output preserves dynamic range at low supply voltages. The 100 kHz bandwidth comfortably handles many slow environmental measurements. Use the lowest practical gain and bandwidth while maintaining the required signal accuracy.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für OPA336UA – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | OPA336PA |
|---|---|---|
| Package | 8-pin SOIC | 8-PDIP; not footprint compatible |
| Brand | Texas Instruments | Texas Instruments |
| Number of Amplifiers | 1 amplifier | 1 amplifier |
| Architecture | CMOS voltage-feedback | CMOS voltage-feedback |
| Supply Configuration | Single supply | Single supply |
| Minimum Supply Voltage | 2.1 V | 2.1 V |
| Maximum Supply Voltage | 5.5 V | 5.5 V |
| Gain-Bandwidth Product | 100 kHz | 100 kHz |
| Quiescent Current | 20 µA per amplifier | 20 µA per amplifier |
| Maximum Offset Voltage | 125 µV | 125 µV |
| Input Bias Current | 1 pA typical | 1 pA typical |
| Open-Loop Gain | 115 dB | 115 dB |
| Output Swing | Within 3 mV of rails at 100 kΩ | Within 3 mV of rails at 100 kΩ |
| Common-Mode Range | Extends to negative supply | Extends to negative supply |
Wichtigste Unterscheidungsmerkmale
- Very low quiescent current for a rail-to-rail operational amplifier (vs. OPA336PA)
- Single-supply operation reaches down to 2.1 V (vs. OPA336PA)
- Surface-mount assembly for compact instrument designs (vs. OPA336PA)
Designhinweise
Account for both quiescent current and load current when calculating battery life. The amplifier contributes approximately 20 µA of quiescent current per channel, while the signal-chain load and pull networks may contribute more. At a 3.3 V supply, the amplifier's static supply contribution is approximately 66 µW before load current is included. Confirm that the source impedance, feedback network, and downstream ADC satisfy the minimum operating and common-mode requirements throughout battery discharge.
Place the op amp close to its source and feedback components, especially when working with high-impedance sensors. Keep the non-inverting and inverting input traces short, avoid routing them beside switching nodes, and use a ground reference that remains quiet. Connect the bypass capacitor directly between the positive and negative supply pins. For the 8-pin SOIC version, confirm pin orientation from the package marking and use the manufacturer's pin configuration before assigning nets.
Do not treat the rail-to-rail input and output descriptions as permission to operate beyond the electrical limits. Output swing is within 3 mV of the rails only at the stated 100 kΩ load, and heavier loads can reduce usable headroom. Likewise, operation from 2.1 V does not guarantee the same output range, bandwidth, and accuracy at every supply voltage. Use the complete Texas Instruments datasheet to select operating conditions, feedback values, and load limits for the design.
Compliance-Informationen
The manufacturer product and ordering information confirms the OPA336UA is a Texas Instruments 8-pin SOIC operational amplifier. Additional compliance declarations require the current manufacturer product page or material-declaration documentation.