Texas Instruments

OPA336UA - 5.5V Micropower RRIO Op Amp | Texas Instruments

Référence : OPA336UA ✓ Actif
Single supply Vdss 20 µA per amplifier Id 8-pin SOIC Package
MOQ : 1 |

OPA336UA Présentation

The Texas Instruments OPA336UA is a single-supply, micropower CMOS operational amplifier with a 5.5 V maximum supply voltage, 100 kHz gain-bandwidth product, and 20 µA typical quiescent current per amplifier, housed in an 8-pin SOIC package. It provides rail-to-rail output and extends its common-mode input range to the negative supply, making it suitable for compact, low-voltage signal-conditioning systems.

An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify the voltage difference between its two inputs. The OPA336 belongs to the microAmplifier family of CMOS op amps, a subcategory of analog amplifiers and linear integrated circuits. Its rail-to-rail output can operate close to both supply rails, while its negative-supply common-mode capability makes single-supply operation practical when input signals remain near ground.

Key features include a maximum offset voltage of 125 µV, typical input bias current of 1 pA, and open-loop gain of 115 dB. The 20 µA quiescent current per amplifier supports battery-powered equipment by limiting static power demand. According to the manufacturer information, output swing reaches within 3 mV of the supply rails with a 100 kΩ load, giving designers useful headroom when operating from a 5.5 V supply.

The OPA336 uses a CMOS voltage-feedback architecture and belongs to a family that includes single, dual, and quad versions with matching core specifications. Its 100 kHz bandwidth is sufficient for low-frequency sensor conditioning, current measurement, instrumentation, and general signal amplification. The 1 pA input bias current is especially useful with high-impedance sources, where input leakage can otherwise create substantial voltage errors.

Typical uses include battery-powered biomedical instrumentation, portable measurement systems, sensor interfaces, low-current monitoring circuits, and portable audio equipment. It can also buffer slow sensor outputs or provide gain ahead of an ADC. Designers should account for its limited bandwidth when processing higher-frequency signals and verify stability with the intended source impedance, load, and feedback network.

For single-supply designs, connect the negative supply pin to ground and bias inputs into the usable common-mode range. Place input and feedback components close to the device, avoid long high-impedance traces, and check output swing at the minimum available output voltage. The 8-pin SOIC package supports conventional surface-mount assembly and is available in tube packaging.

This page combines the manufacturer specifications with pin-level implementation guidance, practical application positioning, and a compatibility-focused comparison. It helps engineers distinguish the OPA336UA from adjacent family members and choose among alternative amplifier approaches without overlooking bandwidth, offset, quiescent-current, supply-voltage, or package constraints.

Alternatives de remplacement direct pour OPA336UA — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec OPA336UA (même facteur de forme et même empreinte) — différant par Package, Open-Loop Gain, Product Type, Maximum Input Offset Voltage, Mounting Type.

Texas Instruments
Package: 8-pin PDIP
Open-Loop Gain: 115 dB typical
Mounting Type: Through-hole
Comparer avec OPA336UA →
Texas Instruments
Package: 8-SOIC
Product Type: Single-supply microPower CMOS operational amplifier
Maximum Input Offset Voltage: 125 uV
Comparer avec OPA336UA →

Aucune alternative de remplacement direct disponible pour ce produit.

Demander des alternatives
ℹ️ 1 référence(s) à boîtier différent masquée(s) — un boîtier différent exige une retouche du PCB et ne constitue pas un remplacement direct. Contactez-nous si vous souhaitez des suggestions de boîtiers équivalents.

OPA336UA Valeurs maximales et caractéristiques électriques

Product Type Single operational amplifier
Architecture CMOS voltage-feedback
Number of Amplifiers 1 amplifier
Supply Type Single supply
Minimum Operating Supply Voltage 2.1 V
Maximum Operating Supply Voltage 5.5 V
Gain-Bandwidth Product 100 kHz
Typical Quiescent Current 20 µA per amplifier
Maximum Input Offset Voltage 125 µV
Typical Input Bias Current 1 pA
Open-Loop Gain 115 dB
Output Swing Within 3 mV of the supply rails at 100 kΩ load
Common-Mode Input Range Extends to the negative supply
Type de sortie Rail-to-rail output
Boîtier 8-pin SOIC

Configuration des broches de OPA336UA

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Broche 1 NC — Not connected
Broche 2 IN- — Inverting input
Broche 3 IN+ — Non-inverting input
Broche 4 V- — Negative supply connection
Broche 5 NC — Not connected
Broche 6 OUT — Output
Broche 7 V+ — Positive supply connection
Broche 8 NC — Not connected

Applications typiques

OPA336UA convient pour 6 applications: Battery-Powered Sensor Conditioning, Portable Medical Instrumentation, Portable Audio Signal Buffer, Low-Current Monitoring Circuit, Industrial Data Acquisition, IoT Environmental Sensor Node.

💊

Battery-Powered Sensor Conditioning

OPA336UA fits low-power sensor front ends because it operates from 2.1 V to 5.5 V and draws approximately 20 µA of quiescent current per amplifier. Place it in a non-inverting or differential gain stage ahead of an ADC, using its 125 µV maximum offset and 1 pA typical input bias current to limit input-referred error. The 100 kHz bandwidth is suitable for temperature, pressure, and chemical sensors with slow bandwidth requirements. Keep traces short and guard high-impedance input nodes to prevent leakage and interference from raising the effective error floor.

💊

Portable Medical Instrumentation

The low quiescent current of OPA336UA makes it useful in portable medical and diagnostic equipment where battery life constrains every stage. Its single-supply operation begins at 2.1 V, while the common-mode range extends to the negative supply and the output approaches the positive rail. These properties allow the amplifier to process small sensor signals without adding a negative rail. The 100 kHz bandwidth suits low-frequency physiological and diagnostic signals; higher-frequency stages may require a wider-bandwidth amplifier. Confirm leakage, noise, and clinical validation requirements for the finished instrument.

🎧

Portable Audio Signal Buffer

OPA336UA can buffer low-level audio or control signals in portable equipment when the required bandwidth is well below 100 kHz. Its rail-to-rail output provides useful swing on a single supply, and output reaches within 3 mV of the supply rails at a 100 kΩ load. The approximately 20 µA quiescent current reduces the static burden on a battery, while the 1 pA typical input bias current is favorable for high-impedance source networks. Check output drive into the actual headphone, transducer, or codec input and verify capacitive-load stability.

⚡

Low-Current Monitoring Circuit

OPA336UA is suitable for amplifying small signals in low-current monitoring systems because its 1 pA typical input bias current limits the error introduced by high source impedance. Place it in a transimpedance or differential stage where the measured signal bandwidth remains within the 100 kHz gain-bandwidth product. The 125 µV maximum offset voltage is particularly relevant to low-level measurements, while the 20 µA typical quiescent current keeps demand low. Include input protection, verify noise performance, and account for the amplifier’s input and output limits across temperature.

🏭

Industrial Data Acquisition

OPA336UA can serve as the input amplifier in a compact industrial data-acquisition channel when the measured bandwidth is low. Its 5.5 V maximum supply and 2.1 V minimum operating voltage support both nominal 3.3 V and 5 V rails, and rail-to-rail output increases usable signal span. The 100 kHz closed-loop bandwidth is suitable for many temperature, pressure, and level signals but not for high-speed vibration sampling. Use proper guarding around sensitive inputs, maintain a stable reference path, and verify the complete analog chain for gain error and channel-to-channel matching.

🧩

IoT Environmental Sensor Node

OPA336UA fits IoT environmental sensor nodes where a small, low-power amplifier conditions outputs from resistive or semiconductor sensors before digitization. Operating from 2.1 V to 5.5 V supports compact energy-harvesting and battery-powered systems, and 20 µA typical quiescent current minimizes standby demand. Its 1 pA typical input bias current is beneficial when sensors have high output impedance, while rail-to-rail output preserves dynamic range at low supply voltages. The 100 kHz bandwidth comfortably handles many slow environmental measurements. Use the lowest practical gain and bandwidth while maintaining the required signal accuracy.

What are the key specifications of OPA336UA that engineers should know?
The OPA336UA is a single-channel, 5.5 V maximum, micropower CMOS op amp with a 100 kHz gain-bandwidth product, 20 µA typical quiescent current, 125 µV maximum offset voltage, and 115 dB open-loop gain. According to the Texas Instruments OPA336 datasheet, it supports operation from 2.1 V, uses rail-to-rail output, and is offered in an 8-pin SOIC package. These characteristics make it most relevant to low-voltage, low-power signal-conditioning designs rather than high-bandwidth precision applications.
Where can I download the OPA336UA datasheet PDF?
The official OPA336UA datasheet can be downloaded from Texas Instruments at https://www.ti.com/lit/gpn/opa336. The manufacturer page identifies OPA336UA as the single-amplifier version in an 8-pin SOIC package. Use that document for the complete pin description, electrical characteristics, recommended operating conditions, and typical performance curves. The related ordering entry is also available through the manufacturer's OPA336UA part-details page.
Where can I find the OPA336UA pinout?
The OPA336UA pinout is shown in the pin-configuration section of the Texas Instruments OPA336 datasheet. The device uses an 8-pin SOIC arrangement with inverting and non-inverting inputs, positive and negative supply connections, output, and no-connect positions. Use the manufacturer pin-description table when assigning PCB nets and confirm orientation against the package marking. The 8-pin SOIC footprint is represented by the package diagram on this product page.
Is OPA336UA suitable for battery-powered applications?
Yes, OPA336UA is specifically suited to battery-powered and portable equipment. According to the Texas Instruments OPA336 product information, the device is a single-supply micropower CMOS amplifier with 20 µA typical quiescent current per amplifier and operation down to 2.1 V. Its low static demand is valuable in always-on sensing systems, although the 100 kHz bandwidth makes it more appropriate for low-frequency or sensor-conditioning signals than for wideband waveform processing.
What is the common-mode input range of OPA336UA?
The OPA336UA common-mode input range extends to the negative supply, as stated in the Texas Instruments OPA336 datasheet. With the negative supply connected to ground, this supports single-supply designs whose inputs operate close to ground. The common-mode limit at the positive end and the precise usable range for a chosen supply must still be checked against the electrical-characteristics table. Output swing is separately specified as within 3 mV of the rails at a 100 kΩ load.
What is the output noise performance of OPA336UA?
The available manufacturer information confirms a 125 µV maximum input offset voltage and 1 pA typical input bias current, but it does not state a numerical output-noise density. The complete Texas Instruments OPA336 datasheet should be consulted for the noise-density figure, input-voltage-noise spectrum, and noise measurements associated with each operating condition. For low-noise design work, use that specification rather than estimating performance from offset voltage alone.
OPA336UA vs OPA336PA - which one should I choose?
OPA336UA and OPA336PA belong to the same OPA336 family and provide the same core single-amplifier functionality, but their packages differ. OPA336UA uses an 8-pin SOIC surface-mount package, while OPA336PA uses an 8-pin DIP package according to the manufacturer ordering information and cross-reference listings. Choose OPA336UA for surface-mount assembly and OPA336PA for a through-hole board; do not treat them as footprint-compatible without a PCB change.
When should I choose OPA336UA over a general-purpose amplifier?
Choose OPA336UA when the design operates from a single supply of 2.1 V to 5.5 V, needs rail-to-rail output, and benefits from approximately 20 µA typical quiescent current per amplifier. Its 100 kHz bandwidth is adequate for slow sensors, measurement loops, and portable equipment. A general-purpose amplifier may be preferable when its wider bandwidth, lower offset, lower noise, higher output current, or dual/quad channel count better matches the application.
Is OPA336UA suitable for high-impedance sensor interfaces?
Yes, OPA336UA can be useful for high-impedance sensor interfaces because the manufacturer specifies 1 pA typical input bias current and a maximum input offset voltage of 125 µV. Low bias current limits the leakage-induced error associated with source resistance, while low offset reduces the input-referred error that can be significant in slow precision measurements. Board cleanliness, guarding, leakage from adjacent traces, and the complete datasheet noise and bias-current limits should still be considered.
Can OPA336UA be used as a voltage buffer?
Yes, OPA336UA can be configured as a voltage follower for a high-impedance source when the signal bandwidth remains below its 100 kHz gain-bandwidth capability. Rail-to-rail output allows the buffered voltage to approach the supply limits under suitable loading, with output swing within 3 mV of the rails at 100 kΩ. Verify capacitive-load stability and use short feedback routing because excessive board capacitance can affect stability.
What can replace OPA336UA as a pin-compatible drop-in?
OPA336UA requires an amplifier with the same 8-pin SOIC pin arrangement, compatible supply range, output swing, input bias current, offset voltage, bandwidth, and stability behavior. The cross-reference results reviewed for this product do not identify a distinct same-package substitute with enough verified data to guarantee drop-in equivalence, so no replacement is asserted here. Use the Request a Quote form on this page to ask about current sourcing, and validate any proposed substitute against the manufacturer datasheet and original circuit requirements.
What is the best OPA336 family alternative for a dual-amplifier design?
The OPA336 family includes dual and quad versions with specifications described as matching the single-channel members. A dual version is appropriate when the circuit requires two amplifiers and the alternative’s exact package, pinout, supply range, and ordering suffix are confirmed from the Texas Instruments datasheet. The cross-reference information identifies OPA2336PA as a dual CMOS op amp, but its DIP package is not footprint-compatible with the 8-pin SOIC OPA336UA.
Is the OPA336UA output able to reach ground on a single supply?
Yes, OPA336UA has a rail-to-rail output, and the manufacturer states that the output swings to within 3 mV of the supply rails with a 100 kΩ load. With a single 5.5 V supply and ground connected to the negative rail, the low output is therefore close to ground under the stated load. Heavier loads can reduce headroom, so check the output-current and output-swing curves for the actual load and supply voltage.
Where can I buy OPA336UA and check the current lead time?
Use the Request a Quote form on this page to request the current price, stock position, packaging availability, and lead time for OPA336UA. The manufacturer part-details page identifies the device as an 8-pin SOIC version of the OPA336 family, while a distributor listing describes it as a single-circuit, rail-to-rail general-purpose amplifier in an 8-SOIC package. Procurement status can change, so obtain the current commercial response through the quote request.
What is the price of OPA336UA?
The current commercial price for OPA336UA should be obtained through the Request a Quote form on this page. Live pricing and inventory vary by order quantity, package configuration, and market conditions, so a static figure would not reliably represent the current offer. Submit the target MPN and required quantity, and request confirmation of any cut tape, tube, or reel packaging needed for production.

Données de référence d'ingénierie pour OPA336UA — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose OPA336UA when the circuit needs a single, low-power amplifier operating from 2.1 V to 5.5 V, especially with high-impedance sources, rail-to-rail output, and signal bandwidth below 100 kHz. Its approximately 20 µA quiescent current, 1 pA typical input bias current, and 125 µV maximum offset voltage are useful in portable sensing and precision measurement systems. OPA336PA offers the same OPA336 family characteristics for through-hole prototyping, but its DIP footprint prevents direct substitution on a SOIC PCB. For dual-channel designs, consider the OPA336 family’s dual member after checking its exact package and pin arrangement. Choose a different amplifier when the application requires substantially more bandwidth, lower noise, lower offset, greater output current, wider supply range, or verified automotive qualification.

Comparaison avec les alternatives

Paramètre Ce produit OPA336PA
Package 8-pin SOIC 8-PDIP; not footprint compatible
Brand Texas Instruments Texas Instruments
Number of Amplifiers 1 amplifier 1 amplifier
Architecture CMOS voltage-feedback CMOS voltage-feedback
Supply Configuration Single supply Single supply
Minimum Supply Voltage 2.1 V 2.1 V
Maximum Supply Voltage 5.5 V 5.5 V
Gain-Bandwidth Product 100 kHz 100 kHz
Quiescent Current 20 µA per amplifier 20 µA per amplifier
Maximum Offset Voltage 125 µV 125 µV
Input Bias Current 1 pA typical 1 pA typical
Open-Loop Gain 115 dB 115 dB
Output Swing Within 3 mV of rails at 100 kΩ Within 3 mV of rails at 100 kΩ
Common-Mode Range Extends to negative supply Extends to negative supply

Principaux différenciateurs

  • Very low quiescent current for a rail-to-rail operational amplifier (vs OPA336PA)
  • Single-supply operation reaches down to 2.1 V (vs OPA336PA)
  • Surface-mount assembly for compact instrument designs (vs OPA336PA)

Notes de conception

Account for both quiescent current and load current when calculating battery life. The amplifier contributes approximately 20 µA of quiescent current per channel, while the signal-chain load and pull networks may contribute more. At a 3.3 V supply, the amplifier's static supply contribution is approximately 66 µW before load current is included. Confirm that the source impedance, feedback network, and downstream ADC satisfy the minimum operating and common-mode requirements throughout battery discharge.

Place the op amp close to its source and feedback components, especially when working with high-impedance sensors. Keep the non-inverting and inverting input traces short, avoid routing them beside switching nodes, and use a ground reference that remains quiet. Connect the bypass capacitor directly between the positive and negative supply pins. For the 8-pin SOIC version, confirm pin orientation from the package marking and use the manufacturer's pin configuration before assigning nets.

Do not treat the rail-to-rail input and output descriptions as permission to operate beyond the electrical limits. Output swing is within 3 mV of the rails only at the stated 100 kΩ load, and heavier loads can reduce usable headroom. Likewise, operation from 2.1 V does not guarantee the same output range, bandwidth, and accuracy at every supply voltage. Use the complete Texas Instruments datasheet to select operating conditions, feedback values, and load limits for the design.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

The manufacturer product and ordering information confirms the OPA336UA is a Texas Instruments 8-pin SOIC operational amplifier. Additional compliance declarations require the current manufacturer product page or material-declaration documentation.

Données vérifiées le : 2026-11-14 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

OPA336UA datasheet OPA336UA pinout OPA336UA datasheet pdf OPA336UA equivalent OPA336UA replacement OPA336UA cross reference OPA336UA price OPA336UA stock OPA336UA vs OPA336PA OPA336UA 100kHz op amp Texas Instruments OPA336UA OPA336UA 8-SOIC footprint OPA336UA battery powered sensor OPA336UA 5.5V operational amplifier OPA336UA application circuit

Composants & termes associés

Texas Instruments OPA336UA OPA336PA OPA2336PA OPA2337PA Operational amplifier Op amp MicroAmplifier CMOS operational amplifier Voltage-feedback amplifier Analog integrated circuit Rail-to-rail output Single-supply operation Common-mode input range Quiescent current Input bias current Input offset voltage Open-loop gain Gain-bandwidth product 2.1 V minimum supply 5.5 V maximum supply 100 kHz bandwidth 8-pin SOIC SOIC family Surface-mount package Battery-powered instrumentation High-impedance sensor Texas Instruments OPA336 datasheet
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ