P1010NSN5KHB - QorIQ P1 1GHz Power Arch SoC | NXP
Teilenummer: P1010NSN5KHB ⚠ Letzte Bestellmöglichkeit| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $45 | $45,00 |
| 10 | $41.5 | $415,00 |
| 100 | $37.8 | $3.780,00 |
| 500 | $34.5 | $17.250,00 |
| 1.000 | $30.53 | $30.530,00 |
P1010NSN5KHB Übersicht
A communications processor (SoC) is a highly integrated device that combines a CPU core, memory controller, network interfaces, and peripheral controllers on a single die. QorIQ P1 series processors expand NXP's communications portfolio into cost- and power-sensitive applications by leveraging 45 nm process technology to deliver up to 1 GHz of performance at power dissipation as low as 1.1 W. The P1010NSN5KHB falls within the broader taxonomy of: embedded microprocessor -> applications processor -> communications SoC -> semiconductor IC.
Key features include a single PowerPC e500v2 core at 1.0 GHz, hardware-accelerated Trusted Boot, integrated DDR3 memory controller with ECC support, three GbE interfaces (one with 1588 support), two USB 2.0 controllers (host + device), two SATA ports, three PCIe Gen 2.0 controllers, and a security engine. The 45 nm process allows fanless operation in sealed industrial enclosures, while the 19x19 mm TEPBGA footprint supports high-density PCB designs.
The P1010 architecture combines a low-latency memory subsystem with a flexible high-speed interconnect, allowing deterministic packet processing alongside rich I/O integration. Hardware virtualization and Trusted Boot features address secure networking and IP-protect firmware requirements, making the P1010NSN5KHB well-suited to industrial control and networked embedded systems.
Typical applications include industrial control and robotics, IP network cameras, factory automation gateways, secure routers, smart-grid endpoint nodes, and low-density network attached storage. The combination of GbE, USB, SATA, and PCIe covers most embedded connectivity requirements without external bridge chips.
When designing with this device, pay close attention to the TEPBGA-425 PCB layout - the 19x19 mm package requires microvia stack-up and careful power-rail decoupling. Thermal management at sustained 1.1 W dissipation is straightforward in still air but requires copper-pour planning when stacked with companion ICs.
This page synthesizes distributor pricing, same-family alternatives, and practical design guidance not found in the manufacturer datasheet, with all data verified against the Octopart, DigiKey, Mouser, and NXP official sources cited below.
Drop-in-Alternativen für P1010NSN5KHB – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit P1010NSN5KHB (gleiche Bauform und Footprint) – abweichend in Core Architecture, Operating Temperature, Package, Process Technology, SATA.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
P1010NXN5HHB
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
P1014NSN5KHB
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
P1010NXE5KHB
✅ Drop-In✓ Auf Lager
$38.4 / Stück
Datenblatt ansehen →P1010NSN5KHB Grenzwerte & elektrische Eigenschaften
| Manufacturer | NXP Semiconductors |
| Series | QorIQ P1 |
| Core Architecture | PowerPC e500v2, 32-Bit |
| Core Count | 1 |
| Maximum Core Frequency | 1.0 GHz |
| Process Technology | 45 nm |
| Typical Power Dissipation | 1.1 W |
| Gehäuse | 425-TEPBGA (19x19 mm) |
| Terminal Form | Ball |
| Number of Terminals | 425 |
| Montageart | Surface Mount |
| Betriebstemperatur | 0C to +105C |
| DDR Memory Support | DDR3 with ECC |
| Ethernet | 3x GbE (one with IEEE 1588) |
| USB | 2x USB 2.0 (host + device) |
| SATA | 2x SATA ports |
| PCIe | 3x PCIe Gen 2.0 controllers |
| Security | Trusted Boot, hardware crypto engine |
| Temperature Grade | OTHER (Industrial) |
P1010NSN5KHB 425-tepbga (19x19 mm) Pinbelegungsleitfaden
Pinbelegung für P1010NSN5KHB (425-tepbga (19x19 mm)-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für P1010NSN5KHB.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
P1010NSN5KHB ist geeignet für 6 Anwendungs: Industrial Robot Controller, IP Network Camera / Video Surveillance, Factory Automation Gateway, Secure Edge Router / SD-WAN Appliance, Smart Grid Endpoint / Intelligent Electronic Device, Low-Density Network Attached Storage.
Industrial Robot Controller
The P1010NSN5KHB fits industrial robot controller designs because its 1.0 GHz e500v2 core delivers deterministic motion-control computation, while the three integrated GbE ports (one with IEEE 1588 hardware timestamping) connect to industrial Ethernet protocols such as EtherCAT, PROFINET, or EtherNet/IP without external PHY bridges. The Trusted Boot engine verifies firmware integrity at power-up, addressing factory cybersecurity requirements. With 1.1 W typical dissipation on 45 nm, the SoC runs fanless inside sealed IP65 enclosures typical of robot cells, and the 0C to +105C industrial temperature range supports continuous operation near servo amplifiers. Recommend pairing with industrial GbE PHY MPNs and DDR3 ECC memory for deterministic motion control.
Empfohlen
IP Network Camera / Video Surveillance
The P1010NSN5KHB powers mid-range IP network cameras by combining a 1 GHz e500v2 processor for H.264/H.265 video encoding with integrated GbE, USB, and SATA peripherals for storage and network connectivity. The Trusted Boot engine ensures the camera firmware has not been tampered with - critical for security-sensitive surveillance deployments in retail, banking, and government. Two SATA ports allow direct attachment of HDD or SSD for local video storage, while three PCIe Gen 2.0 controllers can host a Wi-Fi 6 module or an AI accelerator card. The 45 nm 1.1 W dissipation allows PoE-powered fanless camera housings. Recommend pairing with image sensor ISPs and PoE+ PD controllers.
Empfohlen
Factory Automation Gateway
The P1010NSN5KHB suits factory automation gateways that aggregate sensor data from multiple fieldbuses and forward it to cloud or SCADA systems. The combination of three GbE, two USB 2.0, two SATA, and three PCIe Gen 2.0 ports supports simultaneous connection to industrial sensors, RFID readers, and upstream Ethernet networks. Trusted Boot guarantees the gateway firmware is authenticated before connecting to operational technology networks, addressing IEC 62443 cybersecurity requirements. The 0 to +105C industrial temperature range allows DIN-rail mounting next to servo drives without thermal derating. Recommend pairing with isolated RS-485/RS-232 transceivers and secure-element TPMs.
Empfohlen
Secure Edge Router / SD-WAN Appliance
The P1010NSN5KHB can act as the CPU inside secure edge routers and small SD-WAN appliances by leveraging its three GbE ports for WAN/LAN/DMZ segmentation, plus the Trusted Boot engine for secure firmware load. The 1.0 GHz e500v2 core handles VPN encryption at line rate when paired with a hardware crypto accelerator over PCIe. Two USB 2.0 ports support external storage or LTE modems for failover WAN, and the 0 to +105C temperature range supports outdoor cabinet deployments. Recommend pairing with PCIe-based VPN/security accelerator cards and DDR3 ECC memory modules.
Empfohlen
Smart Grid Endpoint / Intelligent Electronic Device
The P1010NSN5KHB serves smart grid endpoints such as intelligent electronic devices (IEDs), data concentrators, and distribution automation terminals that require secure firmware and deterministic real-time behavior. Its three GbE ports (one with IEEE 1588 timestamping) enable precise PMU measurements and synchrophasor reporting for grid synchronization. The Trusted Boot engine validates substation firmware against cyberattacks - a critical requirement under IEC 61850 and NERC CIP standards. The industrial 0 to +105C temperature range supports deployment in unshielded outdoor cabinets. Recommend pairing with ruggedized Ethernet PHYs and tamper-detection secure elements.
Empfohlen
Low-Density Network Attached Storage
The P1010NSN5KHB is well suited to small-form-factor network attached storage (NAS) appliances for branch offices and SOHO users because its two SATA ports connect directly to HDD or SSD bays without an external RAID controller. The 1.0 GHz e500v2 core handles SMB/NFS/iSCSI file serving at gigabit line rate, while the three GbE ports support link aggregation or multi-VLAN segmentation. Trusted Boot prevents rootkit injection at boot time, addressing the rising ransomware threat to NAS appliances. The 1.1 W typical dissipation keeps the device cool in sealed desktop enclosures. Recommend pairing with enterprise SATA SSDs and DDR3 ECC SO-DIMMs.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für P1010NSN5KHB – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | P1010NXN5HHB | P1014NSN5KHB | P1010NXE5KHB |
|---|---|---|---|---|
| Package | 425-TEPBGA (19x19 mm) | 425-TEPBGA (19x19 mm) - same | 425-TEPBGA (19x19 mm) - same | 425-TEPBGA (19x19 mm) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Architecture | PowerPC e500v2, 32-bit | PowerPC e500v2, 32-bit | PowerPC e500v2, 32-bit | PowerPC e500v2, 32-bit |
| Core Frequency | 1.0 GHz | 1.0 GHz | 1.0 GHz | 1.0 GHz |
| Core Count | 1 | 1 | 1 | 1 |
| GbE Ports | 3 (one with 1588) | 3 (one with 1588) | 3 (one with 1588) | 3 (one with 1588) |
| Trusted Boot | Yes | Yes | Yes | Yes |
| Lifecycle Status | Last Time Buy (EOL announced) | Last Time Buy (EOL announced) | Last Time Buy (EOL announced) | Last Time Buy (EOL announced) |
Wichtigste Unterscheidungsmerkmale
- Same-family drop-in replacement option (vs. P1010NXN5HHB)
- P1 family production alternative (vs. P1014NSN5KHB)
- Extended temperature option within same package (vs. P1010NXE5KHB)
Designhinweise
The 425-TEPBGA (19x19 mm) package requires an 8-layer PCB with microvia stack-up and a continuous thermal copper pour beneath the die. Use 1 oz copper on outer layers and 0.5 oz on inner layers, with the central BGA thermal pad connected to a ground plane through thermal vias (0.3 mm pitch, 12-mil drill). Place DDR3 traces with matched length within 25 mil to avoid signal-integrity issues on the e500v2 memory controller.
Estimated: at 1.1 W typical dissipation and ambient 85C industrial environments, the TEPBGA junction-to-ambient thermal resistance of approximately 18 C/W implies a junction temperature rise of roughly 20C - well within the 105C operating limit. Designers pushing 1.5 W or higher (worst-case workload) should attach a small heatsink or add forced airflow in enclosed cabinets.
Do not substitute the P1010NSN5KHB with non-QorIQ P1 family parts such as the i.MX535 or LS1012A - these use different instruction sets, different peripheral sets, and different PCB footprints. For cross-architecture migration, plan for firmware rebuild, bootloader updates, and reference design re-spin. When using the Trusted Boot engine, do not skip the secure-firmware provisioning step at production - unprovisioned devices leave the security engine disabled and reduce the part to a generic e500v2 SoC.
Compliance-Informationen
RoHS/REACH compliance not present in the verified web data. AEC-Q100 is not applicable to communications processors. Engineers should request the NXP environmental declaration from the product page for full compliance confirmation.
