PCA9518DBR - 5-Channel 400kHz I2C Hub | Texas Instruments
Teilenummer: PCA9518DBR ✗ AbgekündigtPCA9518DBR Übersicht
An I2C hub is a specialized interface IC within the broader hierarchy of I2C interface devices, bus buffers, digital interface controllers, and semiconductors. It is used when a controller must communicate with more devices or over a larger wiring distance than a single unbuffered I2C segment can support. By dividing the bus into electrically isolated segments, the PCA9518DBR helps preserve signal integrity while retaining the two-wire addressing model.
The principal features include five bidirectional downstream channels, a 3 V to 3.6 V operating range, 400 kHz operation, and expandable bus architecture. Each downstream side provides buffering for both clock and data, reducing the electrical loading imposed on the upstream controller. Expansion is possible by connecting additional compatible hubs in a tree arrangement, allowing designers to scale channel count without placing every peripheral on one long segment.
The device supports I2C and SMBus-style bidirectional communication because both protocols depend on wired-AND data lines and shared clock signaling. Buffering minimizes the DC and capacitive loading that would otherwise accumulate as device count and conductor length increase. Designers should still evaluate pull-up placement, rise-time requirements, signal levels, and the maximum permitted bus length for each individual segment.
Typical uses include sensor aggregation, industrial monitoring, test equipment, embedded control systems, and multi-board peripheral buses. The PCA9518DBR is especially useful where a microcontroller or processor must reach sensors, EEPROMs, interface converters, or other low-speed peripherals distributed across a larger assembly.
For PCB implementation, keep the upstream and downstream SDA and SCL paths short, place pull-up resistors at the electrically appropriate locations, and maintain a continuous ground reference between the hub and connected devices. Review the manufacturer datasheet for the exact pin assignment, enable behavior, propagation timing, and recommended input and output capacitance before releasing the layout.
This product page combines the core electrical and package characteristics with application guidance, design considerations, selection criteria, and confirmed replacement information. It helps engineers determine whether a buffered five-channel architecture is appropriate for a given I2C or SMBus topology without relying on raw catalog information alone.
Drop-in-Alternativen für PCA9518DBR – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PCA9518DBR (gleiche Bauform und Footprint) – abweichend in Package, Product Type, Supply Voltage Range.
PCA9518DBT
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →PCA9518DBRG4
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PCA9518PW
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →PCA9518DBR Technische Daten
| Device Type | Expandable five-channel bidirectional I2C/SMBus buffer and hub |
| Number of Downstream Channels | 5 channels |
| Betriebsversorgungsspannung | 3 V to 3.6 V |
| Maximum I2C Bus Frequency | 400 kHz |
| I2C Bus Capacitance per Segment | 400 pF maximum |
| Buffered Signals | Bidirectional SDA and SCL |
| Supported Protocols | I2C and SMBus |
| Expansion Architecture | Expandable hub topology |
| Package Type | SSOP (DB), 20 pins |
| Package Pin Count | 20 pins |
| Montageart | Surface mount |
PCA9518DBR 20 pins Pinbelegungsleitfaden
Pinbelegung für PCA9518DBR (20 pins-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für PCA9518DBR.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
PCA9518DBR ist geeignet für 6 Anwendungs: Industrial Sensor Aggregation, Multi-Board Embedded Control, Test and Measurement Systems, EEPROM and Memory Peripherals, IoT and Edge Sensor Nodes, Board-Level Peripheral Expansion.
Industrial Sensor Aggregation
The PCA9518DBR is appropriate when an industrial controller must connect several groups of sensors over one I2C or SMBus interface. Its five bidirectional downstream channels let the designer place related sensors on separate buffered segments instead of loading the controller with the combined capacitance of every device and cable run. The hub operates from 3 V to 3.6 V at up to 400 kHz, which suits low-speed measurement peripherals that comply with the bus specification. Keep each segment below the 400 pF limit, use appropriate pull-ups, and verify rise time after adding cable and connector capacitance. A common ground and careful isolation of each downstream group are necessary to preserve reliable communication across the assembly.
Multi-Board Embedded Control
The PCA9518DBR can divide a multi-board embedded system into manageable I2C branches, making it useful when a processor must communicate with controllers, memory devices, and expansion cards distributed across a chassis. Five downstream channels provide a practical way to shorten individual traces and reduce the load presented to the upstream bus. Its bidirectional 400 kHz operation suits standard I2C and SMBus peripherals. The topology should be designed as a tree rather than a long daisy chain, with each branch checked for capacitance, pull-up placement, and fault propagation. Validate the complete system at the slowest expected bus rate because accumulated clock skew and weak signal rise time can limit otherwise compliant devices.
Test and Measurement Systems
A test instrument can use the PCA9518DBR to organize several low-speed control or measurement peripherals behind one host interface. The five buffered branches reduce the capacitive burden on the host controller and provide electrical separation between local devices, which is valuable when fixture wiring or cable length makes a single I2C segment impractical. The 3 V to 3.6 V operating range and 400 kHz speed align with many sensor, EEPROM, and low-speed interface components. Engineers should test the worst-case branch capacitance, account for pull-up resistor selection, and avoid adding excessive stub lengths. The result is a more structured fixture bus that can be expanded without loading every peripheral onto the same upstream segment.
EEPROM and Memory Peripherals
The PCA9518DBR can organize multiple I2C EEPROM or other memory peripherals into separate buffered groups when the combined bus load would otherwise approach the protocol limit. The five downstream channels support a practical partition between devices while preserving one logical interface at the controller. Because memory components may have different address ranges, pull-up requirements, and access timing, each group should be characterized rather than treated identically. Place pull-ups where they can maintain the required rise time without overloading the hub output, and maintain short, controlled routing between the hub and each branch. Validate reads and writes at the intended clock rate with the production memory population and cable configuration.
IoT and Edge Sensor Nodes
The PCA9518DBR is useful in edge-computing and IoT assemblies where a central controller connects local sensors, transceivers, and configuration devices over I2C or SMBus. Its five downstream channels provide a straightforward way to split peripherals by function or physical location while operating in the 3 V to 3.6 V range. Buffered branches can improve scalability by limiting the load on the host controller, although each segment must still meet the 400 pF bus-capacitance rule. Low-power designs should also account for the hub's operating current and enable behavior, while firmware should handle unexpected bus-stuck conditions. Firmware should verify each branch during startup to simplify diagnosis of wiring or peripheral failures.
Board-Level Peripheral Expansion
The PCA9518DBR can serve as an expansion point on a controller board that already has too many I2C targets for one practical bus segment. Connecting compatible hubs in a tree lets an engineer create five additional branches while retaining bidirectional SDA and SCL communication at up to 400 kHz. This arrangement can accommodate sensor banks, EEPROMs, and low-speed interface converters without redesigning the host processor. The design must preserve correct pull-up distribution and avoid placing pull-ups on every downstream node indiscriminately, since excessive resistance can slow edges while too little resistance increases the load. Review the hub's timing and enable specifications in the manufacturer datasheet, then verify the completed hierarchy with worst-case devices and cables.
Technische Referenzdaten für PCA9518DBR – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt |
|---|---|
| Package | 20-pin SSOP (DB) |
| Brand | Texas Instruments |
| Device Function | Five-channel bidirectional I2C/SMBus buffer and hub |
| Number of Downstream Channels | 5 channels |
| Operating Supply Voltage | 3 V to 3.6 V |
| Maximum I2C Bus Frequency | 400 kHz |
| I2C Bus Capacitance per Segment | 400 pF maximum |
| Buffered Signals | Bidirectional SDA and SCL |
| Protocol Support | I2C and SMBus |
| Expandability | Yes |
Wichtigste Unterscheidungsmerkmale
- Five independently buffered downstream channels (vs. PCA9518PW)
- Purpose-built I2C and SMBus segment buffering (vs. PCA9548ADBR)
- Supports expandable tree-style bus topologies (vs. PCA9548ADBR)
Designhinweise
Route each downstream SDA and SCL branch as a short, controlled trace from the corresponding hub output, and keep both branches away from noisy switching nodes. The manufacturer describes 400 pF as the maximum I2C bus capacitance for a segment, so calculate trace, device, and connector capacitance before finalizing the layout. Preserve a continuous ground reference across the hub and all connected peripherals.
Select pull-up resistors from the complete bus capacitance, clock rate, and rise-time requirement rather than copying one resistance across every branch. Overly strong pull-ups increase hub output current, while excessively weak pull-ups can produce slow SCL or SDA edges. Confirm that each downstream segment meets the I2C timing limits with the slowest intended clock, the highest operating voltage, and the production load population.
Build the network as a tree with one upstream connection and separate downstream branches; avoid long daisy-chained runs that place multiple devices in the same electrical segment. Keep the PCA9518DBR close to the point where the bus divides so the upstream controller sees only one buffered branch. Review the pin-configuration diagram in the manufacturer datasheet before assigning PCB nets to the 20-pin SSOP footprint.
Do not treat PCA9518PW or PCA9548ADBR as automatic substitutes for PCA9518DBR. The former has a different package style, while the latter has a different multiplexing architecture and channel count. A valid migration requires matching package dimensions, pin functions, voltage levels, timing, bus topology, and lifecycle requirements. Obtain lifecycle guidance directly from the manufacturer before committing a replacement to production.
Compliance-Informationen
The product listing provides quality and ordering information but does not state a specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not stated for this product.