NXP Semiconductors

PCA9663B - 3-Channel Fm+ I2C Controller | NXP | LQFP-48

Teilenummer: PCA9663B ✓ Aktiv
3.3 V Vdss 30 mA Id 48-LQFP, 7 x 7 mm Package
MOQ: 1 |

PCA9663B Übersicht

NXP PCA9663B is a parallel-bus to three-channel I2C-bus controller supporting data rates up to 1 Mbit/s through Fast-mode Plus open-drain channels, packaged in a 48-LQFP 7 x 7 mm package. The device operates from a 3.3 V supply, includes three independent I2C channels, and provides a 4352-byte data buffer per channel for data-intensive serial transfers.

An I2C-bus controller is an interface IC that converts parallel host-bus transactions into serial I2C commands and manages the timing, addressing, and data transfer protocol. The PCA9663B belongs to the parallel-bus-to-I2C-controller segment of the interface IC hierarchy, where it connects a conventional microprocessor or host bus with multiple I2C peripherals. Its three-channel architecture allows separate serial buses to operate independently rather than sharing one serialized channel.

Key features include Fast-mode Plus operation, 1 Mbit/s maximum data rate, 30 mA SCL and SDA sink-current capability, and an internal oscillator trimmed to 1% accuracy. The generous 4352-byte buffer on each channel reduces host-service overhead during sustained transfers. These characteristics make the controller useful when a system must move blocks of sensor, display, communications, or configuration data over I2C without tying up the host on every byte.

The PCA9663B is designed for data-intensive parallel-to-serial conversion. Each channel uses the standard open-drain Fm+ topology, allowing the bus lines to be pulled up externally as required by the system voltage and capacitance. The internal trimmed oscillator removes the need for an external precision timing component, while independent channel state supports simultaneous work on multiple bus domains. Configuration registers and command handling are managed through the parallel host interface.

Typical applications include industrial sensor aggregation, programmable logic or microcontroller peripheral expansion, multi-channel display or control systems, telecommunications equipment, and embedded data-acquisition platforms. Three independent channels can support groups of sensors, memory devices, or transceivers while isolating their traffic. The 1 Mbit/s rate is appropriate for high-volume configuration and monitoring data without moving control traffic to a much faster parallel or serial interface.

PCB design should preserve short, clean SCL and SDA routing, provide the required pull-up resistors, and place decoupling capacitors close to the supply pins. Because the external pull-up value affects rise time and bus timing, it should be selected from the actual board capacitance and the Fm+ requirements. Review the manufacturer's pin and connection guidance before assigning host-bus signals or laying out the three I2C channels.

This product page combines the manufacturer's core electrical and architecture information with package details, sourcing workflows, selection guidance, and practical implementation considerations. It is designed to help engineers determine whether the PCA9663B matches the required channel count, transfer rate, buffering, voltage, and LQFP-48 footprint before beginning PCB design.

Drop-in-Alternativen für PCA9663B – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

PCA9663

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 48-LQFP (7 x 7 mm)
The family revision designation differs, while channel count is 3 versus 3, maximum data rate is 1 Mbit/s versus 1 Mbit/s, and per-channel buffering is 4352 bytes versus 4352 bytes.

📋 Referenzalternative (nicht im Katalog)

PCA9663B Technische Daten

Product Type Parallel-bus to 3-channel Fm+ I2C-bus controller
Number of I2C Channels 3 independent channels
Maximum I2C Data Rate 1 Mbit/s
I2C Mode Fast-mode Plus (Fm+)
Bus Topology Open-drain
Data Buffer per Channel 4352 bytes
Versorgungsspannung 3.3 V
SCL/SDA Output Low Current 30 mA
Internal Oscillator Accuracy 1%
Betriebstemperaturbereich -40°C to +85°C
Gehäuse 48-LQFP, 7 x 7 mm
Package Height 1.40 mm
Montageart Surface mount
Master Mode Single-master mode
Bus Generation Fourth-generation I2C-bus controller
Order Suffix 118

PCA9663B 1.40 mm Pinbelegungsleitfaden

Pinbelegung für PCA9663B (1.40 mm-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für PCA9663B im 1.40 mm-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für PCA9663B.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

PCA9663B ist geeignet für 6 Anwendungs: Industrial Sensor Aggregation, Microcontroller Peripheral Expansion, Programmable Logic Data Acquisition, Communications Equipment Configuration, Multi-Channel Display Control, Embedded Data Acquisition.

🏭

Industrial Sensor Aggregation

The NXP PCA9663B fits industrial sensor aggregation designs that need several I2C groups to remain independent while a parallel host processes their data. Its three I2C channels can divide sensors by type, location, or update rate, and each channel includes a 4352-byte buffer. Fast-mode Plus operation up to 1 Mbit/s accommodates frequent sensor polling and configuration transfers. The 3.3 V supply and -40°C to +85°C operating range align with many embedded industrial controllers. Buffering reduces host service frequency, while separate channels prevent slow traffic on one sensor group from serializing against another group.

🔧

Microcontroller Peripheral Expansion

The PCA9663B is useful when a microcontroller or application processor has too few native I2C ports for displays, memories, sensors, and communications devices. A parallel host bus connects to the controller, which converts host transactions into serial I2C commands across three independent channels. Each 4352-byte buffer supports sustained transfer activity, while operation up to 1 Mbit/s provides higher throughput than standard Fast-mode. The 48-LQFP package integrates three controlled bus interfaces without requiring three separate single-channel controllers, reducing component count and consolidating software-visible channel management.

🖥️

Programmable Logic Data Acquisition

The PCA9663B suits programmable-logic systems that acquire or distribute data across several I2C peripherals through a parallel fabric. Three independent channels allow separate sensor, memory, and accelerator groups to operate concurrently, and the 4352-byte buffer per channel helps absorb bursts of parallel-to-serial traffic. Fast-mode Plus capability at 1 Mbit/s is useful for configuration-heavy logic and data-intensive acquisition paths. The 3.3 V operating supply suits systems built around modern programmable logic, while the external open-drain bus topology requires board-level pull-up selection matched to voltage and capacitance.

🌐

Communications Equipment Configuration

The PCA9663B can organize configuration traffic in communications equipment where transceiver controllers, optical modules, memory devices, and monitoring components use separate I2C segments. Independent channels prevent one device group from monopolizing the controller, and the 4352-byte buffer per channel improves tolerance of bursty parallel-host activity. The 1 Mbit/s Fast-mode Plus rate supports faster register initialization and status polling than conventional 100 kbit/s operation. For equipment with stringent conducted-emissions requirements, low clock rates, controlled switching, and carefully placed pull-ups help maintain predictable bus behavior.

📺

Multi-Channel Display Control

The PCA9663B is a practical choice for systems that manage several display or control peripherals through I2C while retaining a parallel host interface. Three channels can serve separate display groups, touch controllers, or status-monitoring devices, and the 4352-byte buffer per channel is valuable when initialization data arrives in large bursts. Fast-mode Plus support up to 1 Mbit/s accelerates repeated command traffic. The LQFP-48 package provides a manageable surface-mount footprint for multi-function control boards, although designers must route all three buses with adequate pull-ups, short return paths, and attention to signal integrity.

📡

Embedded Data Acquisition

The PCA9663B fits embedded acquisition platforms that receive buffered samples or configuration blocks from several I2C-connected sensors and converters. Three independent channels provide logical separation between sensor banks or instrument stages, while each 4352-byte buffer supports more efficient host-side transfers. Operation up to 1 Mbit/s helps maintain throughput when acquisition rates increase, and the -40°C to +85°C range covers many commercial and industrial environments. Designers should match the 3.3 V supply, select pull-ups from actual bus capacitance, and validate that the parallel timing and host protocol meet the system's sampling deadlines.

What is the PCA9663B and what does it do?
The NXP PCA9663B is a parallel-bus to three-channel I2C-bus controller that converts host-bus transactions into serial I2C transfers. According to the NXP manufacturer datasheet, it provides three independent channels, each with a 4352-byte buffer, and supports Fast-mode Plus operation at data rates up to 1 Mbit/s. It is intended for data-intensive transfers between a parallel host and multiple I2C peripherals.
What are the key specifications of PCA9663B that engineers should know?
The PCA9663B combines three independent I2C channels, a maximum 1 Mbit/s Fast-mode Plus data rate, and 4352 bytes of buffering per channel in a 48-LQFP package. The NXP manufacturer datasheet also specifies a 3.3 V supply, open-drain SCL and SDA outputs with 30 mA sink-current capability, and an internal oscillator trimmed to 1% accuracy. Its operating temperature range is -40°C to +85°C.
How many I2C channels does the PCA9663B support?
The PCA9663B supports three independent I2C-bus channels. According to the NXP manufacturer datasheet, each channel includes a 4352-byte data buffer and can operate at up to 1 Mbit/s using the Fast-mode Plus open-drain topology. Independent channels let one host distribute traffic among separate sensor, memory, display, or communication-device groups without sharing a single serialized I2C channel.
What is the maximum data rate of PCA9663B?
The PCA9663B supports I2C data rates up to 1 Mbit/s through its Fast-mode Plus channels. The NXP manufacturer datasheet identifies the SCL and SDA interface as an open-drain implementation with 30 mA output-low capability. Actual signaling must also satisfy the board's pull-up resistance, capacitance, voltage, and rise-time requirements, so the controller rating alone does not determine final bus timing.
What is the PCA9663B pinout and package?
The PCA9663B is packaged in a 48-LQFP measuring 7 x 7 mm with a stated height of 1.40 mm. Use the pin-description and connection diagrams in the NXP manufacturer datasheet to assign the parallel host-bus, control, supply, clock, and three I2C-channel signals. The package's exposed thermal and layout requirements should be followed exactly on the PCB rather than inferred from the generic LQFP-48 outline.
Where can I download the PCA9663B datasheet PDF?
The official PCA9663B datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/PCA9663.pdf. It contains the general description, feature list, architecture information, electrical characteristics, pin descriptions, connection diagrams, and application guidance. Download that manufacturer document before finalizing power, timing, host-interface, pull-up, and PCB layout decisions.
When should I choose the PCA9663B for an I2C interface?
Choose the PCA9663B when a parallel host must control multiple independent I2C buses and sustained data transfers justify the internal buffering. The NXP manufacturer datasheet specifies three channels, 4352 bytes per channel, and operation up to 1 Mbit/s. It is less suitable when a single low-rate I2C port is sufficient, because a simpler host-integrated I2C controller can reduce board area, software complexity, and component count.
Is the PCA9663B suitable for industrial sensor aggregation?
Yes, the PCA9663B is suitable for industrial sensor aggregation when the design benefits from three separate I2C channels and higher-rate buffered transfers. The NXP manufacturer datasheet specifies a -40°C to +85°C operating range, 1 Mbit/s Fast-mode Plus operation, and a 4352-byte buffer on each channel. These characteristics allow a host to service multiple sensor groups while reducing the frequency of host-side buffer servicing.
What is the best drop-in replacement for PCA9663B?
The closest same-family choice is NXP PCA9663 because it uses the same 48-LQFP controller architecture with three I2C channels and 1 Mbit/s operation. Confirm its suffix, ordering code, pin configuration, electrical limits, and lifecycle status against the NXP datasheet before treating it as a drop-in replacement. No additional same-package replacement was established for the exact PCA9663B ordering designation.
Can PCA9663 replace PCA9663B in an existing design?
The NXP PCA9663 is a candidate for evaluating as a replacement because the family shares three I2C channels, 4352-byte buffering, and 1 Mbit/s operation. It should not be considered an unconditional drop-in without checking the exact suffix and every pin, supply, timing, and reset behavior. Review the manufacturer documentation for both orderable devices and test the revised production board.
What is the best NXP equivalent for PCA9663B?
The NXP PCA9663 is the nearest established same-family equivalent because it retains the three-channel Fm+ controller format and the same core transfer characteristics. According to the NXP manufacturer datasheet, the family supports 1 Mbit/s operation with a 4352-byte buffer per channel. Verify the exact orderable suffix, 48-LQFP pin mapping, operating limits, and firmware or register compatibility before approving substitution.
What are the differences between PCA9663B and PCA9663?
The PCA9663B and PCA9663 share the same principal architecture: three independent I2C channels, Fast-mode Plus operation up to 1 Mbit/s, and a 4352-byte buffer for each channel. The available product naming does not establish every revision-specific electrical difference, so the exact suffix must be checked in NXP's manufacturer documentation. The principal distinction is the B-revision ordering designation rather than a change in the stated channel count or maximum data rate.
Where can I buy PCA9663B and what is its price?
Use the Request a Quote form on this page to request PCA9663B pricing, stock confirmation, minimum order quantity, and lead time. The current commercial terms should be confirmed for the exact 48-LQFP ordering code rather than inferred from a generic family listing. This approach also lets the buyer specify required quantities and delivery conditions without relying on stale pricing information.
Is PCA9663B in stock and what is its lead time?
Current PCA9663B inventory and lead time are confirmed through the Request a Quote form on this page. Include the required quantity, 48-LQFP package preference, and target delivery date in the request. The manufacturer datasheet establishes the device's technical capabilities, but it does not provide a live stock count or a universal lead-time commitment for each procurement quantity.
How should SCL and SDA pull-ups be designed for PCA9663B?
The PCA9663B uses open-drain SCL and SDA outputs, so each bus requires appropriate external pull-up resistors. According to the NXP manufacturer datasheet, the interface supports Fast-mode Plus operation up to 1 Mbit/s and provides 30 mA output-low capability. Select pull-up values using the actual bus voltage, total capacitance, rise-time limit, and pull-down sink current, then validate timing with the intended wiring and peripherals.

Technische Referenzdaten für PCA9663B – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose PCA9663B when a parallel host must communicate with multiple independent I2C groups and the design benefits from 4352 bytes of buffering on each of three channels. Its 1 Mbit/s Fast-mode Plus capability suits data-intensive sensor, display, memory, and communications-device traffic. Choose PCA9663 when its exact suffix, pin mapping, electrical limits, and lifecycle status are confirmed compatible and the lower-level ordering designation better matches the production plan. Do not use either part when a single native host I2C port is sufficient, because the additional controller, clocking, decoupling, and software complexity may provide no practical benefit. Confirm the 48-LQFP footprint, 3.3 V supply, external pull-up design, and host timing before approving either device for an existing PCB.

Vergleich mit Alternativen

Parameter Dieses Produkt PCA9663
Package 48-LQFP (7 x 7 mm) 48-LQFP (7 x 7 mm)
Brand NXP Semiconductors NXP Semiconductors
Product Type Parallel-bus to 3-channel Fm+ I2C-bus controller Parallel-bus to 3-channel Fm+ I2C-bus controller
Number of I2C Channels 3 independent channels 3 independent channels
Maximum Data Rate 1 Mbit/s 1 Mbit/s
I2C Mode Fast-mode Plus (Fm+), open drain Fast-mode Plus (Fm+), open drain
Data Buffer per Channel 4352 bytes 4352 bytes
Supply Voltage 3.3 V 3.3 V
Operating Temperature Range -40°C to +85°C -40°C to +85°C
SCL/SDA Output Low Current 30 mA 30 mA
Internal Oscillator Accuracy 1% 1%

Wichtigste Unterscheidungsmerkmale

  • Three-channel architecture (vs. PCA9663)
  • Buffered parallel-to-serial conversion (vs. PCA9663)
  • Fast-mode Plus throughput (vs. PCA9663)

Designhinweise

Route each SCL and SDA pair as a short, impedance-controlled pair with a continuous ground reference. Place external pull-ups near the bus endpoints or according to the calculated rise-time requirement, and keep the pull-up network away from unrelated switching nodes. Because all three channels use open-drain signaling, correct pull-up placement affects rise time, timing margin, and susceptibility to capacitive coupling.

Connect the 3.3 V supply and ground pins using the manufacturer's decoupling and layout guidance. Place the required local capacitors at the package supply pins with short ground returns, and keep analog or clock-related supply paths away from high-current switching traces. Verify power sequencing and host-interface voltage levels before connecting external logic to prevent uncontrolled current through input protection structures.

Do not treat the 1 Mbit/s controller rating as a complete bus-validity calculation. The actual maximum rate also depends on pull-up resistance, total bus capacitance, sink-current capability, clock timing, peripheral behavior, and trace geometry. Use the manufacturer's electrical characteristics and timing information to calculate rise time, and test the assembled PCB with the longest intended bus and all peripheral loading present.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The manufacturer datasheet identifies the component as an industrial-temperature interface IC. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not included in the accessible product information and require confirmation from current NXP documentation.

Daten verifiziert am: 2026-11-10 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

PCA9663B datasheet PCA9663B datasheet pdf PCA9663B pinout PCA9663B LQFP-48 PCA9663B I2C controller PCA9663B 1 Mbit/s PCA9663B equivalent PCA9663B replacement PCA9663B vs PCA9663 PCA9663B application circuit NXP PCA9663B PCA9663B price

Verwandte Bauteile & Begriffe

NXP Semiconductors PCA9663B PCA9663 PCA9663B,118 I2C controller parallel-bus to I2C-bus converter interface IC semiconductor I2C Fast-mode Plus Fm+ open-drain bus 1 Mbit/s 4352-byte data buffer single-master mode 3.3 V supply 48-LQFP LQFP package family surface-mount package parallel host bus SCL SDA industrial sensor aggregation embedded data acquisition programmable logic
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen