PCA9663B - 3-Channel Fm+ I2C Controller | NXP | LQFP-48
料号: PCA9663B ✓ 量产中PCA9663B 概述
An I2C-bus controller is an interface IC that converts parallel host-bus transactions into serial I2C commands and manages the timing, addressing, and data transfer protocol. The PCA9663B belongs to the parallel-bus-to-I2C-controller segment of the interface IC hierarchy, where it connects a conventional microprocessor or host bus with multiple I2C peripherals. Its three-channel architecture allows separate serial buses to operate independently rather than sharing one serialized channel.
Key features include Fast-mode Plus operation, 1 Mbit/s maximum data rate, 30 mA SCL and SDA sink-current capability, and an internal oscillator trimmed to 1% accuracy. The generous 4352-byte buffer on each channel reduces host-service overhead during sustained transfers. These characteristics make the controller useful when a system must move blocks of sensor, display, communications, or configuration data over I2C without tying up the host on every byte.
The PCA9663B is designed for data-intensive parallel-to-serial conversion. Each channel uses the standard open-drain Fm+ topology, allowing the bus lines to be pulled up externally as required by the system voltage and capacitance. The internal trimmed oscillator removes the need for an external precision timing component, while independent channel state supports simultaneous work on multiple bus domains. Configuration registers and command handling are managed through the parallel host interface.
Typical applications include industrial sensor aggregation, programmable logic or microcontroller peripheral expansion, multi-channel display or control systems, telecommunications equipment, and embedded data-acquisition platforms. Three independent channels can support groups of sensors, memory devices, or transceivers while isolating their traffic. The 1 Mbit/s rate is appropriate for high-volume configuration and monitoring data without moving control traffic to a much faster parallel or serial interface.
PCB design should preserve short, clean SCL and SDA routing, provide the required pull-up resistors, and place decoupling capacitors close to the supply pins. Because the external pull-up value affects rise time and bus timing, it should be selected from the actual board capacitance and the Fm+ requirements. Review the manufacturer's pin and connection guidance before assigning host-bus signals or laying out the three I2C channels.
This product page combines the manufacturer's core electrical and architecture information with package details, sourcing workflows, selection guidance, and practical implementation considerations. It is designed to help engineers determine whether the PCA9663B matches the required channel count, transfer rate, buffering, voltage, and LQFP-48 footprint before beginning PCB design.
直接替换替代料: PCA9663B ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
PCA9663
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
PCA9663B 规格参数
| Product Type | Parallel-bus to 3-channel Fm+ I2C-bus controller |
| Number of I2C Channels | 3 independent channels |
| Maximum I2C Data Rate | 1 Mbit/s |
| I2C Mode | Fast-mode Plus (Fm+) |
| Bus Topology | Open-drain |
| Data Buffer per Channel | 4352 bytes |
| 电源电压 | 3.3 V |
| SCL/SDA Output Low Current | 30 mA |
| Internal Oscillator Accuracy | 1% |
| 工作温度范围 | -40°C to +85°C |
| 封装 | 48-LQFP, 7 x 7 mm |
| Package Height | 1.40 mm |
| 安装类型 | Surface mount |
| Master Mode | Single-master mode |
| Bus Generation | Fourth-generation I2C-bus controller |
| Order Suffix | 118 |
PCA9663B 1.40 mm 引脚配置指南
PCA9663B(1.40 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: PCA9663B.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PCA9663B 适用于 6 应用s: Industrial Sensor Aggregation, Microcontroller Peripheral Expansion, Programmable Logic Data Acquisition, Communications Equipment Configuration, Multi-Channel Display Control, Embedded Data Acquisition.
Industrial Sensor Aggregation
The NXP PCA9663B fits industrial sensor aggregation designs that need several I2C groups to remain independent while a parallel host processes their data. Its three I2C channels can divide sensors by type, location, or update rate, and each channel includes a 4352-byte buffer. Fast-mode Plus operation up to 1 Mbit/s accommodates frequent sensor polling and configuration transfers. The 3.3 V supply and -40°C to +85°C operating range align with many embedded industrial controllers. Buffering reduces host service frequency, while separate channels prevent slow traffic on one sensor group from serializing against another group.
Microcontroller Peripheral Expansion
The PCA9663B is useful when a microcontroller or application processor has too few native I2C ports for displays, memories, sensors, and communications devices. A parallel host bus connects to the controller, which converts host transactions into serial I2C commands across three independent channels. Each 4352-byte buffer supports sustained transfer activity, while operation up to 1 Mbit/s provides higher throughput than standard Fast-mode. The 48-LQFP package integrates three controlled bus interfaces without requiring three separate single-channel controllers, reducing component count and consolidating software-visible channel management.
Programmable Logic Data Acquisition
The PCA9663B suits programmable-logic systems that acquire or distribute data across several I2C peripherals through a parallel fabric. Three independent channels allow separate sensor, memory, and accelerator groups to operate concurrently, and the 4352-byte buffer per channel helps absorb bursts of parallel-to-serial traffic. Fast-mode Plus capability at 1 Mbit/s is useful for configuration-heavy logic and data-intensive acquisition paths. The 3.3 V operating supply suits systems built around modern programmable logic, while the external open-drain bus topology requires board-level pull-up selection matched to voltage and capacitance.
Communications Equipment Configuration
The PCA9663B can organize configuration traffic in communications equipment where transceiver controllers, optical modules, memory devices, and monitoring components use separate I2C segments. Independent channels prevent one device group from monopolizing the controller, and the 4352-byte buffer per channel improves tolerance of bursty parallel-host activity. The 1 Mbit/s Fast-mode Plus rate supports faster register initialization and status polling than conventional 100 kbit/s operation. For equipment with stringent conducted-emissions requirements, low clock rates, controlled switching, and carefully placed pull-ups help maintain predictable bus behavior.
Multi-Channel Display Control
The PCA9663B is a practical choice for systems that manage several display or control peripherals through I2C while retaining a parallel host interface. Three channels can serve separate display groups, touch controllers, or status-monitoring devices, and the 4352-byte buffer per channel is valuable when initialization data arrives in large bursts. Fast-mode Plus support up to 1 Mbit/s accelerates repeated command traffic. The LQFP-48 package provides a manageable surface-mount footprint for multi-function control boards, although designers must route all three buses with adequate pull-ups, short return paths, and attention to signal integrity.
Embedded Data Acquisition
The PCA9663B fits embedded acquisition platforms that receive buffered samples or configuration blocks from several I2C-connected sensors and converters. Three independent channels provide logical separation between sensor banks or instrument stages, while each 4352-byte buffer supports more efficient host-side transfers. Operation up to 1 Mbit/s helps maintain throughput when acquisition rates increase, and the -40°C to +85°C range covers many commercial and industrial environments. Designers should match the 3.3 V supply, select pull-ups from actual bus capacitance, and validate that the parallel timing and host protocol meet the system's sampling deadlines.
工程参考数据: PCA9663B ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PCA9663 |
|---|---|---|
| Package | 48-LQFP (7 x 7 mm) | 48-LQFP (7 x 7 mm) |
| Brand | NXP Semiconductors | NXP Semiconductors |
| Product Type | Parallel-bus to 3-channel Fm+ I2C-bus controller | Parallel-bus to 3-channel Fm+ I2C-bus controller |
| Number of I2C Channels | 3 independent channels | 3 independent channels |
| Maximum Data Rate | 1 Mbit/s | 1 Mbit/s |
| I2C Mode | Fast-mode Plus (Fm+), open drain | Fast-mode Plus (Fm+), open drain |
| Data Buffer per Channel | 4352 bytes | 4352 bytes |
| Supply Voltage | 3.3 V | 3.3 V |
| Operating Temperature Range | -40°C to +85°C | -40°C to +85°C |
| SCL/SDA Output Low Current | 30 mA | 30 mA |
| Internal Oscillator Accuracy | 1% | 1% |
关键差异点
- Three-channel architecture (对比 PCA9663)
- Buffered parallel-to-serial conversion (对比 PCA9663)
- Fast-mode Plus throughput (对比 PCA9663)
设计说明
Route each SCL and SDA pair as a short, impedance-controlled pair with a continuous ground reference. Place external pull-ups near the bus endpoints or according to the calculated rise-time requirement, and keep the pull-up network away from unrelated switching nodes. Because all three channels use open-drain signaling, correct pull-up placement affects rise time, timing margin, and susceptibility to capacitive coupling.
Connect the 3.3 V supply and ground pins using the manufacturer's decoupling and layout guidance. Place the required local capacitors at the package supply pins with short ground returns, and keep analog or clock-related supply paths away from high-current switching traces. Verify power sequencing and host-interface voltage levels before connecting external logic to prevent uncontrolled current through input protection structures.
Do not treat the 1 Mbit/s controller rating as a complete bus-validity calculation. The actual maximum rate also depends on pull-up resistance, total bus capacitance, sink-current capability, clock timing, peripheral behavior, and trace geometry. Use the manufacturer's electrical characteristics and timing information to calculate rise time, and test the assembled PCB with the longest intended bus and all peripheral loading present.
合规信息
The manufacturer datasheet identifies the component as an industrial-temperature interface IC. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not included in the accessible product information and require confirmation from current NXP documentation.