NXP Semiconductors

PCF8591P - 8-Bit I2C ADC/DAC, 4 Inputs | NXP Semiconductors

Teilenummer: PCF8591P ✓ Aktiv
Single supply Vdss 16-pin DIP Package
MOQ: 1 |

PCF8591P Übersicht

NXP Semiconductors PCF8591P is a single-chip, single-supply, low-power 8-bit CMOS data-acquisition device with four analog inputs, one analog output, and a serial I2C-bus interface. It accepts supply voltages from 2.5 V to 6 V and is packaged in a 16-pin DIP, making it suitable for compact analog signal acquisition and output-control systems that use an embedded serial bus.

An ADC/DAC is a data-conversion semiconductor that bridges analog and digital circuitry. The ADC portion converts an analog voltage into a digital value, while the DAC portion converts a digital value into an analog output voltage. A combined ADC/DAC can therefore place sensing, measurement, and analog output generation on one I2C-connected chip. The PCF8591 belongs to the broader data-converter, interface-IC, and power-management-system hierarchy used in embedded equipment.

The principal features are 8-bit conversion resolution, four analog input channels, one analog output channel, and a serial I2C-bus interface. Three hardware-address pins labeled A0, A1, and A2 allow the device address to be programmed, permitting as many as eight devices to share an I2C bus without requiring additional address-decoding hardware. Its single-supply operation and low-power CMOS construction simplify integration in systems that do not need bipolar input or output signals.

Control, address, and converted data are transferred through the I2C interface, reducing the number of parallel signal lines required between the converter and a host microcontroller. The four-input architecture suits multiplexed measurement systems, while the single DAC output provides a simple level for exercising analog control inputs. The 16-DIP package is straightforward to prototype and install through-hole assembly on educational, industrial-control, and legacy embedded boards.

Typical uses include monitoring resistive sensors, reading potentiometer positions, measuring slowly varying analog voltages, generating an analog control level, and building low-cost data-logging or process-control interfaces. The device is particularly useful when a system already communicates through I2C and needs both conversion directions without allocating a separate ADC and DAC. Because the converter is 8-bit, its useful measurement resolution and output granularity are inherently limited compared with higher-resolution data converters.

During schematic design, verify analog input range, output loading, reference behavior, address selection, and logic levels against the manufacturer datasheet before committing a board. Keep analog and digital return currents separated where practical, provide a low-noise supply path, and avoid long sensitive analog traces beside the I2C clock and data lines. Confirm that the host firmware supports the device address selected by A0, A1, and A2.

This product page consolidates the verified device description, datasheet access, package details, application guidance, and replacement-selection considerations. It also distinguishes verified drop-in options from broader functional equivalents so engineers can assess PCB compatibility, bus behavior, and conversion requirements before approving a substitute.

Drop-in-Alternativen für PCF8591P – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

PCF8591P,112

✅ Drop-In
📦 16-DIP
Same 16-DIP footprint and PCF8591 function; ordering suffix identifies the lead-free orderable version

📋 Referenzalternative (nicht im Katalog)

PCF8591P Grenzwerte & elektrische Eigenschaften

Device Type 8-bit CMOS ADC and DAC data-acquisition device
Auflösung 8 bit
Analog Input Channels 4 channels
Analog Output Channels 1 channel
Supply Type Single supply
Minimum Supply Voltage 2.5 V
Maximum Supply Voltage 6 V
Serial Interface I2C serial bus
Hardware Address Pins 3 pins: A0, A1, and A2
Maximum Devices per I2C Bus 8 devices
Package Type 16-pin DIP
Montageart Through-hole
Technology CMOS
Power Class Low power

PCF8591P 16-pin dip Pinbelegungsleitfaden

Pinbelegung für PCF8591P (16-pin dip-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.

Pinbelegungsdiagramm für PCF8591P im 16-pin dip-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für PCF8591P.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

PCF8591P ist geeignet für 6 Anwendungs: Resistive Sensor Interface, Potentiometer Position Measurement, Industrial Process Monitoring, Low-Cost Data Acquisition Module, Analog Control-Level Generator, Embedded Sensor Hub.

🧩

Resistive Sensor Interface

PCF8591P fits a basic resistive-sensor interface because it combines four analog inputs with an I2C data interface in one 16-pin DIP device. A host microcontroller can select an input, initiate conversion, and read the resulting 8-bit value without occupying a parallel data bus. This arrangement is useful for temperature, light, and position elements after conditioning their outputs into the converter's permitted analog range. The value chain should also establish sensor excitation, reference stability, and any required amplifier because the converter itself provides the analog-to-digital interface rather than signal conditioning.

🔧

Potentiometer Position Measurement

PCF8591P can measure the wiper position of a potentiometer through one of its four analog input channels. The 8-bit result provides 256 digital levels across the full conversion range, which is appropriate for basic menu navigation, calibration storage, and coarse mechanical-position feedback. An I2C-capable MCU can read the selected channel without a separate parallel ADC. Designers should verify the analog input limits, reference implementation, and acquisition timing in the NXP datasheet, and should add filtering when the wiper signal is subject to noise or rapid movement.

🏭

Industrial Process Monitoring

PCF8591P is useful in a small industrial monitoring module that needs to observe several slowly changing voltages and report them to a supervisory controller. Four analog inputs allow related measurements to share one converter, while the I2C interface reduces wiring compared with a parallel ADC. The 16-DIP package supports through-hole assembly and serviceable industrial-control boards. Industrial suitability still depends on the complete design: the sensor outputs must remain within the allowed range, the supply must stay between 2.5 V and 6 V, and electrical-noise immunity must be validated at the system level.

📟

Low-Cost Data Acquisition Module

PCF8591P can act as the analog acquisition section of an educational, prototype, or low-cost data-logging module. Its four analog inputs support multiple measurement channels, and the I2C interface allows timestamps, storage, and configuration to be handled by a microcontroller or single-board computer. Eight-bit resolution is appropriate for trend-oriented measurements rather than precision instrumentation. For dependable logging, calibrate each channel, record supply conditions with the measurements, and implement sensor-specific scaling in firmware. The NXP datasheet provides the authoritative operating limits and timing details.

⚡

Analog Control-Level Generator

PCF8591P can generate an analog output level from a digital value while also monitoring up to four analog inputs. A microcontroller can update the output over I2C to represent a setpoint, trim value, or test level, then read the analog inputs to close a simple supervisory loop. The architecture is attractive for legacy industrial and educational controllers because one device supplies both conversion directions. The achievable control resolution remains limited by the 8-bit DAC, and the designer must confirm the output range, settling behavior, and load capability in the manufacturer datasheet before attaching the node to sensitive circuitry.

🌐

Embedded Sensor Hub

PCF8591P can serve as the analog conversion element in an embedded sensor hub linked to an I2C host processor. Multiple analog inputs are scanned through the shared converter, while the single output can provide a basic actuator or reference level. This arrangement is helpful where an MCU already has I2C connectivity and the added analog signals are modest in precision. Address pins A0, A1, and A2 permit several converters to coexist on one bus, with each converter assigned a unique combination. Firmware must also manage channel selection, conversion sequencing, calibration, and fault handling.

What is the PCF8591P datasheet PDF?
The official PCF8591P datasheet PDF is available from NXP Semiconductors at https://www.nxp.com/docs/en/data-sheet/PCF8591.pdf. The manufacturer describes the PCF8591 as a single-chip, single-supply, low-power 8-bit CMOS data-acquisition device with four analog inputs, one analog output, and a serial I2C-bus interface. Use the manufacturer document for the authoritative pin description, electrical limits, operating characteristics, and application guidance.
What does PCF8591P do?
PCF8591P combines an 8-bit ADC and an 8-bit DAC in one package. It can acquire four analog input channels and generate one analog output while communicating with a host through the I2C bus. According to the NXP PCF8591 datasheet, it is a low-power CMOS data-acquisition device intended for embedded analog measurement and output-control systems.
What are the key specifications of PCF8591P that engineers should know?
PCF8591P provides 8-bit conversion resolution, four analog inputs, one analog output, and a serial I2C interface. Its verified supply range is 2.5 V to 6 V, and it is offered in a 16-pin DIP package. Three hardware-address pins, A0, A1, and A2, permit as many as eight devices to share one bus. The NXP datasheet is the controlling reference for timing and electrical limits.
What is the supply voltage range of PCF8591P?
PCF8591P operates from 2.5 V to 6 V. According to the NXP PCF8591 manufacturer datasheet, the device uses a single-supply architecture, so only one supply rail is required for normal operation. Confirm signal and logic levels against the same datasheet before connecting the device to a host MCU or analog circuit.
Where can I find the PCF8591P pinout?
The PCF8591P pinout is shown in the NXP PCF8591 datasheet available at https://www.nxp.com/docs/en/data-sheet/PCF8591.pdf. The package is a 16-pin DIP, so the manufacturer pin-description table should be used when assigning connector pins, test points, and PCB tracks. Pay particular attention to supply, ground, analog I/O, I2C, and the A0-A2 address connections.
How many PCF8591P devices can share one I2C bus?
Up to eight PCF8591 devices can share one I2C bus. The NXP PCF8591 datasheet identifies three hardware-address pins, A0, A1, and A2, which are programmed to establish the device address. Each board location must use a different address combination, and the host firmware must select the corresponding address when transferring commands and data.
Is PCF8591P suitable for sensor measurement?
PCF8591P is suitable for measuring slowly varying analog sensor signals that fit its four input channels and 8-bit conversion resolution. Its I2C interface allows a host microcontroller to retrieve converted values without requiring a parallel ADC bus. The NXP datasheet should be consulted for the permitted input range, input configuration, and acquisition timing before connecting sensor outputs.
Where to buy PCF8591P online?
PCF8591P can be requested through the Request a Quote form on this page. The form is the appropriate channel for checking current availability, order quantities, lead time, and the exact ordering suffix needed for production. Supply status and commercial terms should be confirmed for the specific package and quantity before releasing a purchase order.
What is the price of PCF8591P?
Use the Request a Quote form on this page to obtain the current commercial terms for PCF8591P. Pricing can vary with order quantity, exact suffix, package form, current component supply, and required delivery schedule. This page does not publish a static price figure, so request a quote for the quantity and configuration intended for procurement.
What is the lead time for PCF8591P?
Request the current lead time for PCF8591P through the Request a Quote form on this page. Lead time depends on the exact ordering suffix, stock position, production volume, and required delivery date. When planning a new design, obtain a written schedule and confirmation of continued supply before committing the component to a production release.
Is PCF8591P in stock?
Current PCF8591P stock status should be confirmed through the Request a Quote form on this page. Include the exact suffix, annual usage, and required delivery date in the request so procurement can confirm the appropriate component configuration and schedule. Do not assume availability from a general distributor search page or from a differently suffixed device.
What is the difference between PCF8591P and PCF8591TD-T?
PCF8591P is identified in the verified product information as a 16-pin DIP device, while PCF8591TD-T is discussed separately in a domestic-equivalent article and is associated with a different ordering variant. Package construction, exposed-pad requirements, thermal behavior, and exact pin compatibility must therefore be checked before treating either device as a replacement for the other.
When should I choose PCF8591P over a functional equivalent?
Choose PCF8591P when an existing through-hole 16-DIP PCB requires the verified combination of 8-bit conversion, four analog inputs, one analog output, 2.5 V to 6 V single-supply operation, and I2C addressing. A functional equivalent may be appropriate when the board can be redesigned, but it should not be assumed to match the DIP footprint, pin functions, bus behavior, and application-specific electrical limits.
Is PCF8591P suitable for a low-cost data logger?
PCF8591P can serve as the analog front end of a low-cost data logger because it provides four inputs, one analog output, and an I2C interface in a single 16-DIP package. The 8-bit resolution supports coarse measurements, while the I2C bus simplifies communication with a microcontroller. Storage, calibration, timestamp, and sensor-conditioning requirements remain the responsibility of the complete logger design.
What can replace PCF8591P?
A true PCF8591P replacement must match the 16-DIP footprint, pin functions, 2.5 V to 6 V supply range, I2C protocol behavior, four-input architecture, one output, and address scheme. The TPAFE0808 is described in a domestic-equivalent article as compatible with PCF8591TD-T, but the verified information does not establish it as a pin-compatible DIP replacement for PCF8591P. Validate its package and datasheet before substitution.
What is the best NXP equivalent for PCF8591P?
No alternate NXP MPN is established in the available cross-reference material as a qualified drop-in replacement for PCF8591P. The NXP datasheet identifies PCF8591 as the family device, but ordering suffixes can differ in package form or thermal construction. Search by the required 16-DIP configuration and compare the manufacturer pin description and electrical tables before approving another suffix.

Technische Referenzdaten für PCF8591P – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose PCF8591P when the PCB requires a through-hole 16-DIP data-acquisition device with 8-bit conversion, four analog inputs, one analog output, a 2.5 V to 6 V single supply, and an I2C interface. It is particularly suitable for prototypes, educational equipment, legacy industrial controllers, and sensor hubs where 8-bit resolution is adequate and the host already supports I2C. Do not substitute a functionally similar converter unless its package, pin assignment, address scheme, conversion timing, analog ranges, and electrical limits have been checked against the NXP datasheet. The TPAFE0808 is associated with PCF8591TD-T in a domestic-equivalent article, but that relationship does not establish compatibility with the PCF8591P DIP footprint. For new compact products, consider whether a smaller package and higher-resolution converter would provide better mechanical fit or measurement precision even if the PCB must be redesigned.

Designhinweise

Use the NXP pin-description table to assign the 16-DIP footprint, especially supply, ground, analog I/O, I2C clock and data, and the three address inputs. Keep the I2C wiring away from sensitive analog input traces where the board area permits. Confirm that the physical orientation matches the manufacturer's package drawing because a reversed through-hole installation can place an analog output on a supply pin.

Design the supply path for a continuous 2.5 V to 6 V operating range and place local supply bypassing close to the device pins. Route the return current from digital bus and output circuitry away from analog input returns to reduce common-impedance coupling. Use the manufacturer datasheet for the exact supply-current limits and decoupling recommendations, because those operating conditions determine how much local decoupling is required.

Do not treat the TPAFE0808 reference to PCF8591TD-T as proof that it is a drop-in replacement for the 16-DIP PCF8591P. Before substitution, compare package dimensions, pin assignment, exposed-pad or thermal requirements, address selection, I2C timing, analog ranges, and supply limits. A functional match alone is not enough to authorize a footprint-compatible replacement.

Add appropriate input filtering when the measured source is noisy, and account for settling time when multiplexed channels are scanned. I2C pull-up resistors should be selected for the actual bus voltage, capacitance, and clock rate using the host interface guidance. Avoid long parallel analog traces and keep the reference and analog return paths compact to reduce conversion errors and channel-to-channel disturbance.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The available manufacturer and distributor information does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to the identified general-purpose PCF8591P ordering variant.

Ähnliche Suchanfragen

pcf8591p datasheet PCF8591P datasheet PDF PCF8591P pinout PCF8591P schematic PCF8591P equivalent PCF8591P replacement PCF8591P cross reference PCF8591P application circuit PCF8591P 8-bit ADC DAC PCF8591P 16-DIP package

Verwandte Bauteile & Begriffe

NXP Semiconductors PCF8591P PCF8591 PCF8591TD-T TPAFE0808 8-bit ADC 8-bit DAC analog-to-digital converter digital-to-analog converter ADC/DAC data-acquisition device CMOS I2C bus serial interface hardware addressing A0 A1 A2 16-pin DIP through-hole package single-supply operation embedded sensor interface data logger analog input channel analog output channel
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen