PCF8591P - 8-Bit I2C ADC/DAC, 4 Inputs | NXP Semiconductors
MPN: PCF8591P ✓ सक्रियPCF8591P अवलोकन
An ADC/DAC is a data-conversion semiconductor that bridges analog and digital circuitry. The ADC portion converts an analog voltage into a digital value, while the DAC portion converts a digital value into an analog output voltage. A combined ADC/DAC can therefore place sensing, measurement, and analog output generation on one I2C-connected chip. The PCF8591 belongs to the broader data-converter, interface-IC, and power-management-system hierarchy used in embedded equipment.
The principal features are 8-bit conversion resolution, four analog input channels, one analog output channel, and a serial I2C-bus interface. Three hardware-address pins labeled A0, A1, and A2 allow the device address to be programmed, permitting as many as eight devices to share an I2C bus without requiring additional address-decoding hardware. Its single-supply operation and low-power CMOS construction simplify integration in systems that do not need bipolar input or output signals.
Control, address, and converted data are transferred through the I2C interface, reducing the number of parallel signal lines required between the converter and a host microcontroller. The four-input architecture suits multiplexed measurement systems, while the single DAC output provides a simple level for exercising analog control inputs. The 16-DIP package is straightforward to prototype and install through-hole assembly on educational, industrial-control, and legacy embedded boards.
Typical uses include monitoring resistive sensors, reading potentiometer positions, measuring slowly varying analog voltages, generating an analog control level, and building low-cost data-logging or process-control interfaces. The device is particularly useful when a system already communicates through I2C and needs both conversion directions without allocating a separate ADC and DAC. Because the converter is 8-bit, its useful measurement resolution and output granularity are inherently limited compared with higher-resolution data converters.
During schematic design, verify analog input range, output loading, reference behavior, address selection, and logic levels against the manufacturer datasheet before committing a board. Keep analog and digital return currents separated where practical, provide a low-noise supply path, and avoid long sensitive analog traces beside the I2C clock and data lines. Confirm that the host firmware supports the device address selected by A0, A1, and A2.
This product page consolidates the verified device description, datasheet access, package details, application guidance, and replacement-selection considerations. It also distinguishes verified drop-in options from broader functional equivalents so engineers can assess PCB compatibility, bus behavior, and conversion requirements before approving a substitute.
के लिए ड्रॉप-इन विकल्प PCF8591P — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
PCF8591P,112
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
PCF8591P Maximum Ratings और Electrical Characteristics
| Device Type | 8-bit CMOS ADC and DAC data-acquisition device |
| रेज़ोल्यूशन | 8 bit |
| Analog Input Channels | 4 channels |
| Analog Output Channels | 1 channel |
| Supply Type | Single supply |
| Minimum Supply Voltage | 2.5 V |
| Maximum Supply Voltage | 6 V |
| Serial Interface | I2C serial bus |
| Hardware Address Pins | 3 pins: A0, A1, and A2 |
| Maximum Devices per I2C Bus | 8 devices |
| Package Type | 16-pin DIP |
| माउंटिंग प्रकार | Through-hole |
| Technology | CMOS |
| Power Class | Low power |
PCF8591P 16-pin dip पिन कॉन्फ़िगरेशन गाइड
PCF8591P (16-pin dip पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: PCF8591P.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
PCF8591P के लिए उपयुक्त है 6 अनुप्रयोगs: Resistive Sensor Interface, Potentiometer Position Measurement, Industrial Process Monitoring, Low-Cost Data Acquisition Module, Analog Control-Level Generator, Embedded Sensor Hub.
Resistive Sensor Interface
PCF8591P fits a basic resistive-sensor interface because it combines four analog inputs with an I2C data interface in one 16-pin DIP device. A host microcontroller can select an input, initiate conversion, and read the resulting 8-bit value without occupying a parallel data bus. This arrangement is useful for temperature, light, and position elements after conditioning their outputs into the converter's permitted analog range. The value chain should also establish sensor excitation, reference stability, and any required amplifier because the converter itself provides the analog-to-digital interface rather than signal conditioning.
Potentiometer Position Measurement
PCF8591P can measure the wiper position of a potentiometer through one of its four analog input channels. The 8-bit result provides 256 digital levels across the full conversion range, which is appropriate for basic menu navigation, calibration storage, and coarse mechanical-position feedback. An I2C-capable MCU can read the selected channel without a separate parallel ADC. Designers should verify the analog input limits, reference implementation, and acquisition timing in the NXP datasheet, and should add filtering when the wiper signal is subject to noise or rapid movement.
Industrial Process Monitoring
PCF8591P is useful in a small industrial monitoring module that needs to observe several slowly changing voltages and report them to a supervisory controller. Four analog inputs allow related measurements to share one converter, while the I2C interface reduces wiring compared with a parallel ADC. The 16-DIP package supports through-hole assembly and serviceable industrial-control boards. Industrial suitability still depends on the complete design: the sensor outputs must remain within the allowed range, the supply must stay between 2.5 V and 6 V, and electrical-noise immunity must be validated at the system level.
Low-Cost Data Acquisition Module
PCF8591P can act as the analog acquisition section of an educational, prototype, or low-cost data-logging module. Its four analog inputs support multiple measurement channels, and the I2C interface allows timestamps, storage, and configuration to be handled by a microcontroller or single-board computer. Eight-bit resolution is appropriate for trend-oriented measurements rather than precision instrumentation. For dependable logging, calibrate each channel, record supply conditions with the measurements, and implement sensor-specific scaling in firmware. The NXP datasheet provides the authoritative operating limits and timing details.
Analog Control-Level Generator
PCF8591P can generate an analog output level from a digital value while also monitoring up to four analog inputs. A microcontroller can update the output over I2C to represent a setpoint, trim value, or test level, then read the analog inputs to close a simple supervisory loop. The architecture is attractive for legacy industrial and educational controllers because one device supplies both conversion directions. The achievable control resolution remains limited by the 8-bit DAC, and the designer must confirm the output range, settling behavior, and load capability in the manufacturer datasheet before attaching the node to sensitive circuitry.
Embedded Sensor Hub
PCF8591P can serve as the analog conversion element in an embedded sensor hub linked to an I2C host processor. Multiple analog inputs are scanned through the shared converter, while the single output can provide a basic actuator or reference level. This arrangement is helpful where an MCU already has I2C connectivity and the added analog signals are modest in precision. Address pins A0, A1, and A2 permit several converters to coexist on one bus, with each converter assigned a unique combination. Firmware must also manage channel selection, conversion sequencing, calibration, and fault handling.
के लिए इंजीनियरिंग संदर्भ डेटा PCF8591P — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
डिज़ाइन नोट्स
Use the NXP pin-description table to assign the 16-DIP footprint, especially supply, ground, analog I/O, I2C clock and data, and the three address inputs. Keep the I2C wiring away from sensitive analog input traces where the board area permits. Confirm that the physical orientation matches the manufacturer's package drawing because a reversed through-hole installation can place an analog output on a supply pin.
Design the supply path for a continuous 2.5 V to 6 V operating range and place local supply bypassing close to the device pins. Route the return current from digital bus and output circuitry away from analog input returns to reduce common-impedance coupling. Use the manufacturer datasheet for the exact supply-current limits and decoupling recommendations, because those operating conditions determine how much local decoupling is required.
Do not treat the TPAFE0808 reference to PCF8591TD-T as proof that it is a drop-in replacement for the 16-DIP PCF8591P. Before substitution, compare package dimensions, pin assignment, exposed-pad or thermal requirements, address selection, I2C timing, analog ranges, and supply limits. A functional match alone is not enough to authorize a footprint-compatible replacement.
Add appropriate input filtering when the measured source is noisy, and account for settling time when multiplexed channels are scanned. I2C pull-up resistors should be selected for the actual bus voltage, capacitance, and clock rate using the host interface guidance. Avoid long parallel analog traces and keep the reference and analog return paths compact to reduce conversion errors and channel-to-channel disturbance.
अनुपालन जानकारी
The available manufacturer and distributor information does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to the identified general-purpose PCF8591P ordering variant.