PI7C9X112SLFDEX - PCI-to-PCI Bridge | Diodes Incorporated
Teilenummer: PI7C9X112SLFDEX ✓ AktivPI7C9X112SLFDEX Übersicht
A PCI-to-PCI bridge is a protocol and transaction-layer interface controller that allows legacy PCI devices to operate within a PCI Express system. Within the broader semiconductor hierarchy, this component is a bus controller, interface IC, and PCI Express bridge. Its primary purpose is to translate the signaling and transaction behavior required by a PCI Express link and a conventional PCI bus so that existing PCI cards can communicate with a PCIe-capable host system.
The PI7C9X112SLFDEX uses the PI7C9X112SL device family designation and is available from Diodes Incorporated under an extended-order-code configuration. Distributor records identify the target as a specialized PCI interface IC with a maximum listed supply voltage of 1.1 V, gull-wing terminal geometry, a square HLFQFP package, and 128 terminals. The family datasheet also covers the PI7C9X112SL PCI Express Bridge and provides the primary technical reference for system integration.
The 128-terminal LQFP package provides a large pin count suitable for the parallel PCI bus, power distribution, clocking, control, configuration, and PCIe interface functions. Because its electrical characteristics are not reproduced in the retrieved distributor summaries, engineers should use the PI7C9X112SL datasheet pin-description table, reference design, and recommended-decoupling guidance when assigning PCB nets and validating signal timing.
Typical uses include industrial computers, embedded industrial controllers, test equipment, communication appliances, and legacy PCI expansion systems that need a PCIe-to-PCI bridge. The bridge is particularly useful when an established PCI card or peripheral must be retained while the host platform transitions to PCI Express.
PCB implementation requires careful routing of the conventional PCI signals and correct power, reference-clock, configuration, and reset connections. Keep high-speed PCIe traces short and continuous, observe the manufacturer’s reference-plane and decoupling arrangements, and verify all connector-facing signals against the applicable PCI and PCI Express system-design constraints.
This product page consolidates package, ordering, interface, and procurement information with practical PCB-planning guidance and a controlled replacement assessment. It also distinguishes a verified same-package ordering alternative from unverified functional equivalents, helping engineers identify where a direct drop-in substitution can be considered and where a complete interface review is mandatory.
Drop-in-Alternativen für PI7C9X112SLFDEX – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
PI7C9X112SLFDE
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PI7C9X112SLFDEX Grenzwerte & elektrische Eigenschaften
| Device Type | PCI-to-PCI bridge interface |
| Interface Classification | PCI Express bridge |
| Bus Category | PCI / PCIe interface |
| Gehäuse | 128-LQFP (14 mm x 14 mm) |
| Package Code | HLFQFP |
| Package Shape | Square |
| Terminal Geometry | Gull wing |
| Number of Terminals | 128 terminals |
| Maximum Supply Voltage | 1.1 V |
| Montageart | Surface mount |
| Shipping Package | Tape and reel |
| Reel Quantity | 1,000 units |
| Ordering Code | X suffix configuration |
| Product Family | PI7C9X112SL |
PI7C9X112SLFDEX tape and reel Pinbelegungsleitfaden
Pinbelegung für PI7C9X112SLFDEX (tape and reel-Gehäuse). Dieses Leistungsbauteil verfügt über Gate-, Drain- und Source-Anschlüsse. Bei nicht gepolten Gehäusen entnehmen Sie die genaue Ausrichtung von Pin 1 und Footprint-Details dem Herstellerdatenblatt. Typische Anwendungen sind Netzteilentwurf, Motoransteuerung und Lastschaltung.
Keine detaillierten Pinbelegungsdaten verfügbar für PI7C9X112SLFDEX.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
PI7C9X112SLFDEX ist geeignet für 6 Anwendungs: Industrial Computer PCI Expansion, Embedded PCIe-to-PCI Controller, PCI Express Test Equipment, Telecommunications Equipment, Legacy PCI Migration Platform, PCI Security and Imaging Appliance.
Industrial Computer PCI Expansion
The PI7C9X112SLFDEX fits an industrial computer that retains conventional PCI expansion hardware while using a PCI Express host interface. The device’s listed PCI-to-PCI bridge function provides the protocol-conversion path needed by the legacy bus, while its 128-LQFP package provides the pin count required for parallel PCI signals, power, control, and clock functions. The implementation should follow the PI7C9X112SL reference design, including its clocking, reset, decoupling, and PCB-routing requirements.
Empfohlen
Embedded PCIe-to-PCI Controller
The PI7C9X112SLFDEX is applicable in embedded controllers that need to support a conventional PCI peripheral from a PCIe-based host processor. Its documented PCI Express Bridge function allows the system architect to reuse established PCI hardware instead of redesigning the expansion card. Integration remains dependent on exact lane configuration, bus width, timing, and operating limits, so engineers should verify the PI7C9X112SL datasheet and reference schematic before committing the board layout.
Empfohlen
PCI Express Test Equipment
The PI7C9X112SLFDEX can support test equipment that must exercise conventional PCI cards through a modern PCIe-based measurement or computing platform. The 128-terminal package supports the numerous connections associated with a parallel PCI interface and its associated control functions. Because bridge behavior, clock tolerances, transaction timing, and power requirements determine test coverage, the laboratory design should use the manufacturer application guidance and explicitly verify every bus-width and speed mode used by the equipment.
Empfohlen
Telecommunications Equipment
The PI7C9X112SLFDEX is suited to communications equipment that retains PCI-based accelerator, interface, or monitoring modules while adopting a PCI Express system architecture. The bridge function provides a defined route between the two interface generations, reducing the need to replace every legacy module immediately. Board-level adoption nevertheless requires validation of signal integrity, reference-clock distribution, reset behavior, isolation requirements, thermal performance, and the complete electrical limits published in the PI7C9X112SL documentation.
Empfohlen
Legacy PCI Migration Platform
The PI7C9X112SLFDEX supports migration platforms intended to extend the useful life of conventional PCI equipment. A PCIe-capable controller can use the bridge rather than requiring immediate replacement of every installed PCI card, which is useful for capital-intensive industrial and laboratory systems. A successful migration still requires a detailed compatibility review covering supported bus width, operating modes, voltage domains, clocking, interrupt behavior, configuration space, and the mechanical dimensions of the 14 mm by 14 mm LQFP land pattern.
Empfohlen
PCI Security and Imaging Appliance
The PI7C9X112SLFDEX can bridge established PCI imaging, capture, or security modules into a PCIe-based appliance. This arrangement is useful when specialized acquisition hardware has a long service life and still uses the conventional PCI interface. The bridge should be placed according to the manufacturer reference layout, with careful treatment of high-speed PCIe routing, conventional PCI signal timing, reference-clock jitter, power sequencing, and isolation. Functional testing must cover the exact transaction types and transfer modes expected from the installed peripheral.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PI7C9X112SLFDEX – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PI7C9X112SLFDE |
|---|---|---|
| Brand | Diodes Incorporated | Diodes Incorporated |
| Package | 128-LQFP (14 mm x 14 mm) | 128-LQFP (14 mm x 14 mm) |
| Device Type | PCI-to-PCI bridge interface | PCI-to-PCI bridge interface |
| Interface Classification | PCI Express bridge | PCI Express bridge |
| Number of Terminals | 128 terminals | 128 terminals |
| Ordering Suffix | X suffix configuration | E suffix configuration |
Wichtigste Unterscheidungsmerkmale
- Matches the specialized 128-LQFP bridge platform (vs. PI7C9X112SLFDE)
- Uses the X ordering configuration (vs. PI7C9X112SLFDE)
- Directly identified as a PCI-to-PCI bridge (vs. PI7C9X2G404SLBFDEX)
Designhinweise
Use the PI7C9X112SL datasheet pin table and package drawing as the authority for every one of the 128 terminal assignments. Treat the 14 mm by 14 mm LQFP footprint as a precision routing problem: verify pad dimensions, solder-mask clearance, paste stencil aperture, pin-one orientation, and assembly clearances before releasing artwork. Do not infer an unused terminal or exposed-pad connection from the generic HLFQFP package designation.
Implement the PCIe and conventional PCI interfaces using the layer stackup and routing topology shown by the manufacturer. Keep PCIe traces short, continuous, impedance controlled, and referenced to an uninterrupted ground plane. Place decoupling and clock-network components close to their associated pins. Validate trace geometry with the fabricator’s stackup because connector launches, vias, and return-path discontinuities can change interface behavior even when the schematic is correct.
Do not approve a substitution solely because both order codes are described as 128-LQFP PCI-to-PCI bridge devices. Verify the ordering table, electrical ratings, operating-temperature grade, lifecycle status, pin configuration, and supported interface modes for PI7C9X112SLFDE against PI7C9X112SLFDEX. A same-package result establishes mechanical similarity, not full functional or qualification equivalence.
Build the power network around the manufacturer’s recommended supply topology, component values, startup behavior, and decoupling locations. The available distributor record lists a maximum supply voltage of 1.1 V, but it does not identify every rail or tolerance. Confirm all nominal voltages, sequencing constraints, current limits, and load behavior in the datasheet, then verify the assembled board’s rail limits and startup sequence under worst-case system conditions.
Compliance-Informationen
The retrieved manufacturer and distributor summaries do not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Current declarations should be obtained from Diodes Incorporated before use in environmental or qualification documentation.