PIC24F08KM102-E/SP - 8KB Flash 16-bit XLP MCU | Microchip
Teilenummer: PIC24F08KM102-E/SP ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $4.2 | $4,20 |
| 10 | $3.78 | $37,80 |
| 100 | $3.15 | $315,00 |
| 500 | $2.74 | $1.370,00 |
| 1.000 | $2.42 | $2.420,00 |
PIC24F08KM102-E/SP Übersicht
A 16-bit microcontroller (MCU) is a single-chip processor with a 16-bit data path, registers and ALU, offering higher arithmetic precision and code density than 8-bit MCUs while remaining simpler than 32-bit Cortex-M parts. The PIC24F family sits inside Microchip's broader dsPIC/PIC24 portfolio (16-bit MCU -> dsPIC/PIC24 family -> 8/16/32-bit MCU hierarchy -> embedded microcontroller -> semiconductor IC). XLP (eXtreme Low Power) variants add nanoWatt technology for sleep currents in the nanoamp range, enabling battery-powered products with multi-year lifetimes.
Key features include 8KB (2.75K x 24) Flash with self-programmability, 1KB SRAM, 512B EEPROM for non-volatile data, 12-bit A/D converter with up to 500 ksps, multiple Enhanced CCP, SCCP and PWM modules, configurable logic cells (CLC), UART, SPI and I2C peripherals, plus a 32MHz internal oscillator. On-chip safety features comprise Brown-out Detect/Reset, LVD, POR, PWM and a Watchdog Timer, supporting reliable operation in harsh industrial and automotive environments.
The device uses a modified Harvard architecture with separate program and data buses, a 16-element working register array and hardware DO/REPEAT loops, achieving close to 1.5 MIPS/MHz. A wide 1.8V-3.6V operating range (PIC24F variant) supports both 3V and 5V-tolerant mixed-signal designs while consuming only nanoWatt sleep current.
Typical applications include industrial sensor conditioning, low-power consumer devices, automotive body and HVAC subsystems, battery-powered IoT edge nodes and small motor-control boards. Its small footprint, XLP nanoWatt modes and rich peripherals make it ideal when 8-bit MCUs run out of performance but 32-bit parts add cost or complexity.
When designing with this MCU, plan for ICD/ICSP header access for in-circuit debugging and reserve the dedicated CONFIG pins early. Use the CLC and PWM peripherals to replace external glue logic and ensure decoupling follows Microchip's recommended 100nF + bulk capacitor layout.
This page synthesizes distributor pricing, drop-in alternatives and design notes not found in the manufacturer datasheet.
Drop-in-Alternativen für PIC24F08KM102-E/SP – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC24F08KM102-E/SP (gleiche Bauform und Footprint) – abweichend in Package, ADC, Maximum CPU Speed, Core Architecture, Mounting Type.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC24F08KM102-I/SP
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC24F16KM102-E/SP
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC24F08KM102-E/SO
✅ Drop-In✓ Auf Lager
$1.98 / Stück
Datenblatt ansehen →PIC24F08KA102-E/SO
✅ Drop-In✓ Auf Lager
$1.85 / Stück
Datenblatt ansehen →PIC24F08KL402-E/SP
✅ Drop-In✓ Auf Lager
$1.85 / Stück
Datenblatt ansehen →PIC24F08KL401-E/SS
✅ Drop-In✓ Auf Lager
$1.69 / Stück
Datenblatt ansehen →PIC24F04KM102-E/SP
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC24F08KM102-E/SP Grenzwerte & elektrische Eigenschaften
| Core | PIC24F 16-bit RISC |
| Series | PIC XLP 24F |
| Program Memory (Flash) | 8 KB (2.75K x 24) |
| RAM | 1 KB |
| EEPROM | 512 B |
| Maximum CPU Speed | 32 MHz |
| Operating Voltage Range | 1.8 V to 3.6 V |
| ADC | 12-bit |
| Comparators | Yes |
| PWM Modules | Yes (MCCP/SCCP) |
| Configurable Logic Cell (CLC) | Yes |
| Brown-out Detect/Reset | Yes |
| Low-Voltage Detect (LVD) | Yes |
| Power-on Reset (POR) | Yes |
| Watchdog Timer (WDT) | Yes |
| Communication Peripherals | UART, SPI, I2C |
| Gehäuse | 28-pin SPDIP (DIP-28, 0.300 inch, 7.62mm) |
| Montageart | Through-Hole |
| Betriebstemperaturbereich | -40 C to +125 C (extended) |
| Temperature Grade | Automotive (E) |
| RoHS-Status | Compliant |
| MSL-Level | Not applicable (through-hole) |
PIC24F08KM102-E/SP Pin-Konfiguration
| Pin 1 | MCLR — Master Clear (Reset) input, internal pull-up |
| Pin 2 | RA0 — Port A bit 0 / analog input / CLC |
| Pin 3 | RA1 — Port A bit 1 / analog input / CLC |
| Pin 4 | RB0 — Port B bit 0 / analog input |
| Pin 5 | RB1 — Port B bit 1 / analog input |
| Pin 6 | RB2 — Port B bit 2 / analog input |
| Pin 7 | RB3 — Port B bit 3 / analog input |
| Pin 8 | VSS — Ground reference |
| Pin 9 | OSC1 — External oscillator input / CLKIN |
| Pin 10 | OSC2 — External oscillator output / CLKOUT |
| Pin 11 | RC0 — Port C bit 0 / analog input |
| Pin 12 | RC1 — Port C bit 1 / analog input |
| Pin 13 | RC2 — Port C bit 2 / analog input |
| Pin 14 | RC3 — Port C bit 3 / analog input |
| Pin 15 | RC4 — Port C bit 4 / analog input |
| Pin 16 | RC5 — Port C bit 5 / analog input |
| Pin 17 | RC6 — Port C bit 6 / TX |
| Pin 18 | RC7 — Port C bit 7 / RX |
| Pin 19 | VSS — Ground reference |
| Pin 20 | VDD — Positive supply voltage |
| Pin 21 | RB4 — Port B bit 4 / analog input |
| Pin 22 | RB5 — Port B bit 5 / analog input / PGED1 |
| Pin 23 | RB6 — Port B bit 6 / analog input / PGEC1 |
| Pin 24 | RB7 — Port B bit 7 / analog input |
| Pin 25 | RB8 — Port B bit 8 / analog input |
| Pin 26 | RB9 — Port B bit 9 / analog input |
| Pin 27 | RA2 — Port A bit 2 / analog input |
| Pin 28 | RA3 — Port A bit 3 / analog input |
Typische Anwendungen
PIC24F08KM102-E/SP ist geeignet für 7 Anwendungs: Industrial Sensor Conditioning, Low-Power Consumer Electronics, Automotive Body and HVAC Modules, Battery-Powered IoT Edge Nodes, Small Motor Control Boards, Medical Monitoring Devices, Human-Machine Interface Panels.
Industrial Sensor Conditioning
The PIC24F08KM102-E/SP's 12-bit ADC and integrated comparators suit bridge, RTD and 4-20 mA sensor front-ends where 8-bit MCUs lack dynamic range. Its nanoWatt XLP sleep currents (under 100 nA typical) enable remote battery-powered transmitters that wake briefly to digitize, log and transmit. The 32MHz CPU handles MODBUS RTU framing and on-sensor linearization without an external DSP. Designers should budget for a 100 nF decoupling cap adjacent to VDD and an analog AVSS tie to a clean ground pour.
Empfohlen
Low-Power Consumer Electronics
Battery-powered consumer devices such as remote controls, fitness bands and e-paper wearables benefit from the PIC24F08KM102-E/SP's nanoWatt XLP sleep modes and configurable logic cell (CLC). The CLC can replace discrete gates, reducing BOM cost and PCB area. With 8KB Flash the device comfortably hosts BLE/HID stacks via SPI/UART peripherals, while the 1KB RAM supports small RTOS shells. Operating from 1.8V to 3.6V, the MCU can run directly from a single CR2032 or Li-ion cell with no extra regulator.
Empfohlen
Automotive Body and HVAC Modules
With the E temperature grade (-40C to +125C), the PIC24F08KM102-E/SP is well-suited for body controllers, HVAC flap motors and lighting drivers where AEC-Q100 is not strictly required. Its MCCP/SCCP PWM modules can drive LED strings and small BLDC fans directly. The Brown-out Detect/Reset and Watchdog Timer protect against cranking transients, while the wide 1.8-3.6V range tolerates 12V battery drops after regulator staging. CAN-style networking can be implemented with an external MCP2515 if needed.
Empfohlen
Battery-Powered IoT Edge Nodes
The PIC24F08KM102-E/SP's nanoWatt technology, the RTCC-based sleep scheduling and 12-bit ADC make it a strong fit for wireless sensor nodes (temperature, humidity, leak detection) transmitting via sub-GHz or BLE radios. Idle currents in the tens of nanoamps extend coin-cell lifetime to several years. The 8KB Flash holds a typical LoRaWAN/MQTT-SN stack with sensor drivers, while the CLC implements wake-on-event timers without firmware polling. Pair with an SPI-connected radio and a low-Iq LDO.
Empfohlen
Small Motor Control Boards
Small BLDC, brushed DC and stepper motor controllers benefit from the PIC24F08KM102-E/SP's MCCP/SCCP PWM, 32MHz CPU and configurable logic cell. The MCU can generate center-aligned PWMs at 32kHz while the 12-bit ADC samples back-EMF or current-sense signals. With 1KB RAM it accommodates field-oriented control (FOC) lite algorithms for low-RPM fans or pumps. Hardware PWM fault inputs and CLC event triggers improve safety response time over software-only implementations.
Empfohlen
Medical Monitoring Devices
For non-critical medical monitors (pulse-oximetry accessories, wearable thermometers, pill dispensers), the PIC24F08KM102-E/SP offers the precision of a 16-bit core, integrated 12-bit ADC and EEPROM storage for calibration data. The XLP nanoWatt sleep enables multi-day operation on a single coin cell, while the Watchdog Timer and Brown-out Reset provide the safety features required by IEC 62304 risk-class A/B designs. Use external ADC/MUX for ECG-class signals where higher resolution is required.
Empfohlen
Human-Machine Interface Panels
The PIC24F08KM102-E/SP can drive small HMI panels with LED indicators, PWM dimming and segment displays, while handling capacitive or mechanical button scanning via the Configurable Logic Cell. The 32MHz CPU allows responsive 100Hz UI update rates with no perceptible lag, and the 1KB SRAM supports menu structures and animation state machines. Hardware UART/SPI/I2C bridges easily to external graphics drivers or Bluetooth modules for wireless control panels.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC24F08KM102-E/SP – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC24F08KM102-I/SP | PIC24F16KM102-E/SP | PIC24F08KM102-E/SO | PIC24F08KL402-E/SP |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SPDIP (DIP-28) | 28-SPDIP (DIP-28) | 28-SPDIP (DIP-28) | 28-SOIC | 28-SPDIP (DIP-28) |
| Flash Memory | 8 KB | 8 KB | 16 KB | 8 KB | 8 KB |
| RAM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| EEPROM | 512 B | 512 B | 512 B | 512 B | 512 B |
| Operating Voltage | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Temperature Grade | -40C to +125C (E) | -40C to +85C (I) | -40C to +125C (E) | -40C to +125C (E) | -40C to +125C (E) |
| ADC Resolution | 12-bit | 12-bit | 12-bit | 12-bit | 12-bit |
| CLC (Configurable Logic) | Yes | Yes | Yes | Yes | No |
Wichtigste Unterscheidungsmerkmale
- Extended automotive temperature grade (vs. PIC24F08KM102-I/SP)
- Configurable Logic Cell (CLC) for glue-logic replacement (vs. PIC24F08KL402-E/SP)
- Through-hole 28-SPDIP for prototyping (vs. PIC24F08KM102-E/SO)
Designhinweise
Place a 100 nF ceramic decoupling capacitor within 5 mm of every VDD pin and tie VSS to a low-impedance ground pour; for noise-sensitive analog designs add a 10 uF bulk capacitor near the IC. Estimated: at 32 MHz / 3.3V typical core draw is 8-10 mA, so a low-Iq LDO such as MCP1700 is recommended for sleep-friendly battery designs. Always enable the on-chip BOR/LVD via CONFIG to protect against brown-outs.
Route the ICSP/ICD pins (PGECx/PGEDx, MCLR) directly to an in-circuit programming header with no series resistors, and add an ESD protection diode on MCLR if the connector is exposed. Keep the 32 MHz oscillator traces short (<10 mm) and surround them with a ground guard ring. The 28-SPDIP through-hole pads handle 0.1 inch pitch footprints easily; ensure through-hole annulus is at least 0.5 mm for wave-solder reliability.
Do not leave CONFIG bits at default - configure the WDT, BOR, LVD and oscillator mode before first program run. The ADC requires the analog pins to be explicitly configured as analog in the ANSEL register; digital inputs on floating analog pins cause excess current. Avoid driving PWM outputs above their absolute maximum and remember that 5V signals exceed the 3.6V absolute maximum, requiring a level translator.
The 28-SPDIP package has excellent thermal dissipation through its leads; in still air the junction-to-ambient thermal resistance is typically 60-80 C/W. Estimated: at 32 MHz / 3.3V the device draws ~10 mA, dissipating ~33 mW, so junction rise is ~2-3 C above ambient - no heatsink required. For high ambient (>85 C) designs verify against the -40 to +125 C operating range and derate accordingly.
Compliance-Informationen
RoHS compliant per Microchip product page. E temperature grade covers -40C to +125C but is not formally AEC-Q100 qualified - contact Microchip for automotive-grade ordering codes.
