PIC24FJ32MC101-E/SS - 16-bit 32KB Motor MCU | Microchip
Teilenummer: PIC24FJ32MC101-E/SS ✓ AktivPIC24FJ32MC101-E/SS Übersicht
A PIC24FJ microcontroller belongs to the 8-bit and 16-bit embedded-controller hierarchy used for real-time control, sensor conditioning, communications, and actuator management. Unlike a general-purpose microcontroller focused primarily on connectivity or human-interface functions, this device combines a 16-bit core with dedicated resources for motor-drive timing and analog measurement. Its compact package supports cost-sensitive industrial, appliance, and embedded equipment designs.
The device provides 32 KB of program Flash organized as 11K × 24 bits and 2 KB of data RAM. It operates from 3 V to 3.6 V, allowing use with common 3.3 V power systems. CTMU supports capacitive measurement and touch-oriented sensing, while the motor-control PWM peripherals provide hardware-assisted waveform generation. A peripheral pin-select feature can map supported digital functions onto designated I/O pins, reducing software configuration complexity.
The 16-bit architecture and 16 MIPS execution rate provide a practical balance between control-loop performance, memory efficiency, and implementation cost. Program memory is adequate for embedded motor algorithms, state machines, and communication handlers, while 2 KB of SRAM supports working variables and control calculations. The 20-SSOP outline also reduces board area compared with larger leaded motor-control packages.
Typical uses include small brushless-DC and brushed motor controllers, appliance drive modules, battery-operated pumps, fan controllers, industrial sensor nodes, and compact two-wheeled-vehicle controls. The combination of CTMU, PWM peripherals, PPS, and a 3.3 V operating range is especially useful when touch sensing, timing synchronization, and motor control must share a cost-sensitive embedded platform.
PCB design should reserve clean routing for motor-control signals, provide local bypass capacitance at the supply pins, and keep switching or high-current motor outputs away from sensitive analog and timing paths. Firmware should validate startup, fault handling, and motor states before enabling PWM output, and the selected crystal or timing configuration should be checked against the application’s speed and timing requirements.
This page combines the PIC24FJ32MC101-E/SS specification summary, sourcing guidance, family-level alternatives, and practical design considerations. It also helps engineers compare package constraints, memory, peripherals, and application fit before committing a 20-pin motor-control design to production.
Drop-in-Alternativen für PIC24FJ32MC101-E/SS – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC24FJ32MC101-E/SS (gleiche Bauform und Footprint) – abweichend in Package, CPU Architecture, Operating Temperature, Peripheral Pin Select, Product Type.
PIC24FJ32MC102-E/SS
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →PIC24FJ32MC104-E/SS
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
PIC24FJ32MC101-I/SS
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →PIC24FJ32MC101-E/SS Grenzwerte & elektrische Eigenschaften
| Product Type | 16-bit motor-control microcontroller |
| CPU Architecture | 16-bit PIC24F |
| Maximum Instruction Rate | 16 MIPS |
| Program Memory | 32 KB Flash (11K × 24 bits) |
| Data Memory | 2 KB SRAM |
| Supply Voltage Range | 3 V to 3.6 V |
| ADC Resolution | 10 bits |
| Motor-Control PWM | Integrated MCPWM peripherals |
| Touch and Analog Peripheral | Integrated CTMU |
| Peripheral Pin Select | PPS supported |
| Gehäuse | 20-pin SSOP |
| Montageart | Surface mount |
| Betriebstemperatur | -40 °C to +125 °C |
| Automotive Qualification | AEC-Q100 family variant indicated by the automotive listing |
PIC24FJ32MC101-E/SS 20-pin ssop Pinbelegungsleitfaden
Pinbelegung für PIC24FJ32MC101-E/SS (20-pin ssop-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für PIC24FJ32MC101-E/SS.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
PIC24FJ32MC101-E/SS ist geeignet für 6 Anwendungs: Compact Brushless DC Motor Control, Appliance Motor and Pump Driver, Battery-Operated Fan Controller, Capacitive Touch Control Panel, Industrial Sensor and Actuator Node, Two-Wheeled Vehicle Motor Control.
Compact Brushless DC Motor Control
The PIC24FJ32MC101-E/SS fits compact brushless-DC controllers because its 16-bit core executes at 16 MIPS while the MCPWM peripherals provide deterministic switching waveforms. The 32 KB of Flash can hold a speed-control loop, commutation state machine, and protection logic, while 2 KB of SRAM provides working space for control calculations. Its 3 V to 3.6 V operating range also simplifies integration with a common 3.3 V motor-drive rail. The principal design trade-off is that a single low-pin-count package requires careful allocation of PWM, communication, sensing, and debug functions.
Empfohlen
Appliance Motor and Pump Driver
The PIC24FJ32MC101-E/SS is appropriate for appliance motors, pumps, and small circulation systems where deterministic PWM timing and compact packaging are central requirements. Its 16 MIPS processing rate can support a current-control loop, load handling, and fault supervision in one controller, while CTMU can add touch or level sensing without requiring a separate input device. The 20-SSOP footprint preserves board area, but motor transients and heating remain the primary engineering concerns. Separate isolation or filtering may be required when the motor and controller share a compact board.
Empfohlen
Battery-Operated Fan Controller
The PIC24FJ32MC101-E/SS suits low-power fan controllers because it combines a 16-bit control engine, 2 KB of SRAM, and 32 KB of Flash in a compact 20-SSOP package. PWM generation, CTMU-based controls, and PPS timing can support variable-speed operation, touch controls, and synchronization with other system clocks. Its 3 V to 3.6 V supply range aligns with common 3.3 V battery-derived rails. Firmware should include stalled-rotor, startup, and brownout handling because the MCU does not replace external motor protection hardware.
Empfohlen
Capacitive Touch Control Panel
The PIC24FJ32MC101-E/SS can combine touch sensing and motor control in one compact controller through its integrated CTMU and MCPWM resources. A designer can use CTMU for keypad, slider, or level sensing while the 16-bit core handles display updates, motor sequencing, and communication. The 20-SSOP package reduces total component count in appliances and compact industrial equipment. CTMU accuracy still depends on careful sensor grounding, guard structures, filtering, and calibration, while switching-motor energy can interfere with sensitive measurements.
Empfohlen
Industrial Sensor and Actuator Node
The PIC24FJ32MC101-E/SS works well in small industrial nodes that must acquire analog measurements and operate a limited number of actuators. Its 10-bit ADC supports basic process measurements, the 16 MIPS core provides sufficient control-loop bandwidth, and 32 KB of Flash supports local logic and configuration storage. The 20-SSOP outline is useful in distributed equipment where board area is constrained. Industrial deployments should add transient protection, calibration, watchdog strategy, and continuous environmental testing because controller qualification alone does not validate the complete sensor node.
Empfohlen
Two-Wheeled Vehicle Motor Control
The PIC24FJ32MC101-E/SS can serve as a compact motor controller for traction, steering, or braking functions in small two-wheeled vehicles. The 16-bit core at 16 MIPS supports field-oriented control or other computationally intensive current-control methods, and the MCPWM peripherals assist deterministic bridge-drive timing. CTMU may support interface or presence sensing. Safety-critical designs require independent protection paths, watchdog behavior, fault logging, and validation across voltage, temperature, vibration, and electromagnetic environments; the MCU itself does not provide complete functional-safety certification.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC24FJ32MC101-E/SS – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC24FJ32MC102-E/SS | PIC24FJ32MC104-E/SS | PIC24FJ32MC101-I/SS |
|---|---|---|---|---|
| Package | 20-SSOP | 20-SSOP | 20-SSOP | 20-SSOP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| CPU Architecture | 16-bit PIC24F | 16-bit PIC24F | 16-bit PIC24F | 16-bit PIC24F |
| Maximum Instruction Rate | 16 MIPS | 16 MIPS | 16 MIPS | 16 MIPS |
| Program Memory | 32 KB Flash | 32 KB Flash | 32 KB Flash | 32 KB Flash |
| Data Memory | 2 KB SRAM | 2 KB SRAM | 2 KB SRAM | 2 KB SRAM |
| Supply Voltage Range | 3 V to 3.6 V | 3 V to 3.6 V | 3 V to 3.6 V | 3 V to 3.6 V |
| Motor-Control PWM | Integrated MCPWM peripherals | Integrated MCPWM peripherals | Integrated MCPWM peripherals | Integrated MCPWM peripherals |
| CTMU | Integrated | Integrated | Integrated | Integrated |
| PPS Support | Supported | Supported | Supported | Supported |
Wichtigste Unterscheidungsmerkmale
- Dedicated motor-control integration (vs. PIC24FJ32MC101-I/SS)
- Compact 20-pin implementation (vs. PIC24FJ32MC102-E/SS)
- Balanced embedded resources (vs. PIC24FJ32MC104-E/SS)
Designhinweise
Place the required input bypass capacitor close to each VDD pin and connect the VSS pins to the ground plane using short, low-impedance paths. Route motor-switching outputs away from CTMU inputs, ADC inputs, and oscillator circuitry. A continuous ground reference beneath the 20-SSOP footprint helps control return current, while a quiet analog ground region can reduce coupling between sensing and switching sections.
Treat the MCPWM outputs as high-current board interfaces even though the microcontroller itself only generates control signals. Keep gate-drive traces short, use separate return paths for power-stage current, and place protection or snubber networks near the power devices rather than near the MCU. Differential or sensitive sensor traces should not run beneath motor-switching nodes or alongside high di/dt conductors.
Do not assume that a family member with the same package is firmware-compatible without reviewing its peripheral map. Check PWM channel availability, PPS assignments, CTMU channels, interrupt vectors, analog functions, and pin multiplexing before migrating a design. The E and I ordering suffixes can affect qualification and sourcing decisions even when the electrical core and footprint remain unchanged.
The PIC24FJ32MC101-E/SS operates from 3 V to 3.6 V, so the motor-driver rail must remain within that range during startup, braking, and transient conditions. Use adequate bulk and local ceramic capacitance between the regulator and MCU. A separate regulator or filtering strategy may be needed if the motor bridge produces rail disturbances that exceed the allowable input ripple.
Compliance-Informationen
An automotive listing references an AEC-Q100 family variant, but the exact qualification status of PIC24FJ32MC101-E/SS should be confirmed with the manufacturer. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation for the exact ordering code.