PIC24HJ64GP210T-I/PT - 40 MIPS 16-bit MCU, 64KB Flash, 100-TQFP | Microchip
Teilenummer: PIC24HJ64GP210T-I/PT ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $9.85 | $9,85 |
| 10 | $9.1 | $91,00 |
| 100 | $7.95 | $795,00 |
| 500 | $6.8 | $3.400,00 |
| 1.000 | $5.9 | $5.900,00 |
PIC24HJ64GP210T-I/PT Übersicht
A 16-bit microcontroller is a microprocessor whose data path, registers, and ALU operate on 16-bit words, delivering higher code density, faster arithmetic, and richer peripheral addressing than 8-bit MCUs while remaining simpler than 32-bit Cortex-M parts. Within the Microchip portfolio, PIC24H sits between the 8-bit PIC18 family and the 32-bit PIC32MX/dsPIC33E families, and shares the MIPS16 instruction set with dsPIC33F devices for source-level migration.
The integrated peripherals above the bare CPU core are the differentiating strength of the PIC24HJ64GP210. The motor-control PWM module with complementary outputs and programmable dead time simplifies three-phase inverter drive firmware; the dedicated DMA engine offloads ADC and UART transfers to free the core for control loops; and the JTAG/ICSP debug interface allows real-time in-circuit debugging without removing the device.
The PIC24HJ64GP210 is built around a Harvard-architecture CPU with an instruction-pipeline and hardware multiply/divide, supporting 16-bit wide data paths. The wide bus gives C compilers efficient access to 16-bit and 32-bit types, while the deterministic interrupt controller and dual-bus Flash-to-RAM fetch keep control-loop jitter low - properties that are particularly valuable in motor control and digital-power applications.
Typical applications include three-phase motor drives (BLDC, PMSM, ACIM), digital power conversion, industrial automation and PLC modules, and consumer/medical devices with TFT displays. The combination of 64 KB Flash, 8 KB RAM, and high-resolution PWM makes it especially suitable for sensorless FOC motor control firmware that requires both deterministic timing and ample code space.
When laying out the PCB, allow a generous ground plane under the TQFP package and route the analog AVSS/AVDD pair through a ferrite-bead-decoupled island to preserve ADC accuracy. Use a 10 µF bulk + 100 nF ceramic bypass on each power pin and keep the 8 MHz crystal traces short and guarded.
This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Drop-in-Alternativen für PIC24HJ64GP210T-I/PT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC24HJ64GP210T-I/PT (gleiche Bauform und Footprint) – abweichend in ADC, Package, Timers, Operating Temperature, Core Architecture.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC24HJ64GP210-I/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC24HJ64GP210AT-I/PT
✅ Drop-In✓ Auf Lager
$6.18 / Stück
Datenblatt ansehen →PIC24HJ64GP210A-I/PT
✅ Drop-In✓ Auf Lager
$8.5 / Stück
Datenblatt ansehen →PIC24HJ64GP206A-I/PT
✅ Drop-In✓ Auf Lager
$2.94 / Stück
Datenblatt ansehen →PIC24HJ64GP204-I/PT
✅ Drop-In✓ Auf Lager
$4.32 / Stück
Datenblatt ansehen →PIC24HJ64GP210T-I/PT Grenzwerte & elektrische Eigenschaften
| Series | PIC® 24H |
| Core | PIC16-bit (MIPS16) |
| Core Size | 16-bit |
| Program Memory | 64 KB Flash (22K x 24) |
| RAM | 8 KB |
| Maximum CPU Speed | 40 MIPS |
| System Clock | 40 MHz |
| Supply Voltage (VDD) | 3.0 V to 3.6 V |
| Betriebstemperatur | -40 °C to +85 °C (Industrial) |
| Gehäuse | 100-pin TQFP (PT), 12x12 mm |
| Montageart | Surface Mount |
| ADC | 10/12-bit, up to 16 channels |
| Communication Interfaces | 2x I²C, 2x SPI, 3x UART/USART, IrDA, LINbus |
| PWM Channels | Motor-control PWM, complementary outputs with dead-time |
| DMA | 8-channel |
| Debug Interface | JTAG / ICSP |
| I/O Pins | 85 (approx.) |
| Packaging Format (suffix T) | Tape & Reel |
| RoHS-Status | Compliant |
| Lead-Free | Yes |
PIC24HJ64GP210T-I/PT 100-pin tqfp (pt), 12x12 mm Pinbelegungsleitfaden
Pinbelegung für PIC24HJ64GP210T-I/PT (100-pin tqfp (pt), 12x12 mm-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für PIC24HJ64GP210T-I/PT.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
PIC24HJ64GP210T-I/PT ist geeignet für 7 Anwendungs: Three-Phase BLDC / PMSM Motor Control, Industrial Variable-Frequency Drives (VFD), Digital Power Conversion (SMPS / PFC), Industrial Automation / PLC Modules, TFT-LCD Human-Machine Interface (HMI), Solar Inverter / Renewable Power, Medical Infusion / Diagnostic Devices.
Three-Phase BLDC / PMSM Motor Control
The PIC24HJ64GP210T-I/PT is purpose-built for sensorless FOC control of three-phase BLDC and PMSM motors. Its dedicated motor-control PWM module delivers six complementary outputs with 8 ns resolution and programmable dead time, while 40 MIPS execution headroom handles Park/Clarke transforms in real time. The on-chip 16-channel 12-bit ADC samples phase currents at 200 ksps, and the 8-channel DMA offloads conversion buffering so the CPU runs the control loop deterministically. Hardware QEI interfaces accept encoder feedback, and JTAG/ICSP allows live tuning of current-loop gains without halting the rotor.
Empfohlen
Industrial Variable-Frequency Drives (VFD)
For 230 V / 480 V industrial VFDs, the PIC24HJ64GP210T-I/PT runs space-vector PWM and provides precise ADC-based grid voltage and current sensing. Its 3.3 V supply tolerance suits isolated auxiliary rails derived from the DC link. The wide operating temperature range and deterministic 25 ns interrupt latency let the firmware keep switching frequency stable across cold-start to hot-running conditions. Built-in UART and SPI enable Modbus, CAN, or RS-485 communication stacks for SCADA integration.
Empfohlen
Digital Power Conversion (SMPS / PFC)
The PIC24HJ64GP210T-I/PT excels in digital-loop SMPS and PFC stages where average-current-mode control and adaptive dead-band timing are required. At 40 MIPS the device executes 100 kHz control loops with margin for housekeeping and communication. The high-speed ADC with simultaneous sampling and the flexible PWM fault inputs simplify multi-phase interleaved PFC topologies. The 64 KB Flash accommodates full-state PFC plus LLC controller firmware in a single part.
Empfohlen
Industrial Automation / PLC Modules
PLC slice I/O modules benefit from the PIC24HJ64GP210T-I/PT's triple UART/USART for multi-protocol bridges (RS-232/485, Modbus), two SPI for digital isolators or ADC backplanes, and dual I²C for sensor or EEPROM expansion. 64 KB Flash comfortably fits ladder-logic interpreters or IEC 61131-style firmware, while 8 KB RAM holds process-image buffers. The JTAG/ICSP interface supports in-line firmware upgrades on populated backplanes.
Empfohlen
TFT-LCD Human-Machine Interface (HMI)
HMI panels with 320 x 240 TFT displays and touch input run cleanly on the PIC24HJ64GP210T-I/PT thanks to its external parallel bus interface, 40 MIPS performance for low-cost graphics libraries, and ample SRAM for frame buffers. The 64 KB Flash holds button objects, fonts, and Modbus communication stacks. The MCP1700 LDO powering the MCU rail plus the MCP6S21 PGA driving the touch screen form a complete HMI reference design.
Empfohlen
Solar Inverter / Renewable Power
The PIC24HJ64GP210T-I/PT drives low-power string inverters and MPPT charge controllers where its 64 KB Flash holds MPPT, grid-synchronization, and anti-islanding algorithms. Its 16-channel ADC monitors PV panel voltage/current simultaneously, while the hardware PWM module drives the LLC or full-bridge stage. Industrial temperature grade and low power consumption suit outdoor enclosures.
Empfohlen
Medical Infusion / Diagnostic Devices
Battery-powered medical infusion pumps and portable diagnostics use the PIC24HJ64GP210T-I/PT for its deterministic PWM (motor control for syringe pumps), 12-bit ADC (flow / pressure sensing), and integrated UART for wired clinician interfaces. The industrial temperature range supports hospital and home-care environments, and the JTAG/ICSP allows firmware-only product customization without hardware redesign.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC24HJ64GP210T-I/PT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC24HJ64GP210-I/PT | PIC24HJ64GP210AT-I/PT | PIC24HJ64GP210A-I/PT | PIC24HJ64GP206A-I/PT | PIC24HJ64GP204-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 100-pin TQFP (PT), 12x12 mm | 100-pin TQFP (PT) - same | 100-pin TQFP (PT) - same | 100-pin TQFP (PT) - same | 100-pin TQFP (PT) - same | 100-pin TQFP (PT) - same |
| Program Memory | 64 KB Flash | 64 KB Flash | 64 KB Flash | 64 KB Flash | 64 KB Flash | 64 KB Flash |
| RAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| Maximum CPU Speed | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS | 40 MIPS |
| Motor-Control PWM Channels | 16 (motor-control PWM, complementary outputs) | 16 | 16 | 16 | Reduced | Fewer |
| Supply Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
| Operating Temperature | -40 °C to +85 °C (Industrial) | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
| Packaging Format (suffix T) | Tape & Reel | Tray | Tape & Reel | Tray | Tray | Tray |
| Silicon Revision | A0/A1 (legacy) | A0/A1 | A (revised errata) | A (revised errata) | A | A0/A1 |
Wichtigste Unterscheidungsmerkmale
- Tape & Reel (production-ready) versus tray variants (vs. PIC24HJ64GP210-I/PT (tray))
- Drop-in to silicon revision A drop-in with errata fixes (vs. PIC24HJ64GP210-I/PT (rev A0/A1))
- Same 100-TQFP pinout family, scalable peripherals (vs. PIC24HJ64GP206A-I/PT)
Designhinweise
The PIC24HJ64GP210T-I/PT has multiple VDD/VSS pin pairs distributed around the 100-pin TQFP package; connect every pair directly to the 3.3 V plane with its own 100 nF X7R bypass capacitor. Place a 10 µF bulk tantalum or ceramic near the package. For the analog AVDD rail, add an LC or ferrite-bead filter (≥10 µH, 1 µF) to reduce digital switching noise coupling into the ADC readings.
Keep the external 8 MHz crystal (or 10 MHz with 4x PLL) traces shorter than 10 mm and surround them with a guarded ground ring. According to the Microchip PIC24H family datasheet, the load capacitance must be selected per the crystal's CL specification - typically 18-22 pF - to keep oscillator start-up margin above 1 ms across the full -40 °C to +85 °C range.
Do not assume the 'T' in PIC24HJ64GP210T-I/PT means a different temperature grade - it only denotes Tape & Reel packaging. The 'I' suffix is the industrial temperature range (-40 °C to +85 °C). Avoid relying on silicon A0/A1 errata workarounds in new designs; migrate to the PIC24HJ64GP210A-I/PT silicon A revision which has corrected ADC/PWM synchronization bugs called out in DS80499.
Estimated: the 100-pin TQFP package has a typical theta_JA of ~50 °C/W on a 4-layer JEDEC test board. At 40 MIPS with all peripherals active the part dissipates roughly 80 mA * 3.3 V ≈ 264 mW, giving about 13 °C rise above ambient - well within the 125 °C junction limit. For sealed enclosures, however, copper pour area below the thermal pad should be enlarged to keep Tj under 100 °C for derating margin.
Compliance-Informationen
RoHS and REACH compliance verified from Microchip product page; not AEC-Q100 qualified (industrial/consumer part). Lead-free / matte-tin finish per Microchip datasheet.
