PIC32MX170F512L-I/PT - 50MHz 32-bit MCU 512KB Flash | Microchip
Teilenummer: PIC32MX170F512L-I/PT ✓ Aktiv| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $6.5 | $6,50 |
| 10 | $5.85 | $58,50 |
| 100 | $5.2 | $520,00 |
| 500 | $4.7 | $2.350,00 |
| 1.000 | $4.2 | $4.200,00 |
PIC32MX170F512L-I/PT Übersicht
What is a PIC32MX microcontroller? PIC32MX is Microchip's MIPS32 M4K-based MCU family positioned between 16-bit dsPIC/PIC24 and Cortex-M-class parts. It uses a Harvard-architecture 32-bit core with single-cycle multipliers, deterministic interrupt latency, and 16-bit instructions for code density, while remaining compatible with classic PIC peripherals. PIC32MX parts are widely used in HMI, USB audio, and industrial control designs.
Key features of the PIC32MX170F512L include 50 MHz / 83 DMIPS performance, 512 KB Flash with pre-fetch cache, 64 KB RAM, USB 2.0 full-speed OTG, CAN 2.0B, two I2S, four SPI, five UART, five I2C, PMP for external memory/graphics, a 16-channel 10-bit 1 Msps ADC, five 16-bit timers/capture/compare, an RTCC, and Peripheral Pin Select (PPS) for nearly every digital function.
The M4K core uses a 5-stage pipeline with branch shadowing and a hardware multiply/divide unit; Flash is mirrored into the 32-bit instruction fetch path through a 128-bit wide bus with a 4-word pre-fetch cache, while data passes through a separate SRAM bus, eliminating single-cycle Flash wait states in most cases.
Typical applications include USB audio interfaces (USB + I2S + DAC chains), HMI panels with LCD via PMP, industrial CAN nodes, capacitive touch keypads, motor-control sequencers, and low-cost graphics + USB dongles. Industrial temperature grade (-40C to +85C) and the 100-pin TQFP give enough I/O for layered systems.
Design consideration: when migrating from PIC24/dsPIC or PIC32MX3/4/5/6/7 families, verify PPS mapping because PIC32MX1xx has fewer remappable pins and a smaller RAM/Flash than PIC32MX5/6/7. Decoupling must include a 100 nF per VDD/AVDD pair and a bulk 4.7 uF on VDDCORE.
This page consolidates distributor pricing for PIC32MX170F512L-I/PT, alternatives for the 100-pin TQFP footprint, and design notes beyond the manufacturer datasheet.
Drop-in-Alternativen für PIC32MX170F512L-I/PT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit PIC32MX170F512L-I/PT (gleiche Bauform und Footprint) – abweichend in ADC, Package, Parallel Master Port (PMP), Operating Temperature, USB.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
PIC32MX170F512L-I/PF
✅ Drop-In✓ Auf Lager
$6.45 / Stück
Datenblatt ansehen →PIC32MX170F512HT-50I/PT
✅ Drop-In✓ Auf Lager
$4.32 / Stück
Datenblatt ansehen →PIC32MX270F512L-I/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC32MX170F512L-50I/PT
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
PIC32MX170F512L-I/PT Grenzwerte & elektrische Eigenschaften
| Core Architecture | MIPS32 M4K |
| Maximum CPU Clock | 50 MHz (83 DMIPS) |
| Flash Program Memory | 512 KB (512K x 8) |
| SRAM Data Memory | 64 KB |
| Operating Voltage Range | 2.5 V to 3.6 V |
| Betriebstemperaturbereich | -40 C to +85 C (Industrial) |
| Gehäuse | 100-pin TQFP (PT) 12x12 mm |
| ADC | 10-bit, up to 1 Msps, up to 16 channels |
| USB | USB 2.0 Full-Speed OTG |
| CAN | CAN 2.0B |
| SPI Modules | 4 (configurable as I2S) |
| I2S Modules | 2 |
| UART Modules | 5 |
| I2C Modules | 5 |
| Parallel Master Port (PMP) | Yes, dual read/write buffers |
| Peripheral Pin Select (PPS) | Yes |
| Timers / Capture / Compare | 5 x 16-bit |
| RTCC | Yes |
| mTouch Capacitive Touch | Yes |
| DMA Channels | Up to 8 |
| Montageart | Surface Mount |
| RoHS-Status | Compliant |
PIC32MX170F512L-I/PT Pin-Konfiguration
| Pin 1 | RG15 — I/O pin RPn |
| Pin 2 | VDD — Power supply |
| Pin 3 | RP0 — I/O pin |
| Pin 4 | RP1 — I/O pin |
| Pin 5 | RG6 — I/O pin |
| Pin 6 | RG7 — I/O pin |
| Pin 7 | RG8 — I/O pin |
| Pin 8 | RG9 — I/O pin |
| Pin 9 | MCLR — Master Clear reset |
| Pin 10 | RP2 — I/O pin |
| Pin 11 | RP4 — I/O pin |
| Pin 12 | RP3 — I/O pin |
| Pin 13 | RP5 — I/O pin |
| Pin 14 | VSS — Ground |
| Pin 15 | VDD — Power supply |
| Pin 16 | RP6 — I/O pin |
| Pin 17 | RP7 — I/O pin |
| Pin 18 | RP8 — I/O pin |
| Pin 19 | RP9 — I/O pin |
| Pin 20 | VSS — Ground |
| Pin 21 | VDD — Power supply |
| Pin 22 | RP10 — I/O pin |
| Pin 23 | RP11 — I/O pin |
| Pin 24 | RP12 — I/O pin |
| Pin 25 | RP13 — I/O pin |
| Pin 26 | RP14 — I/O pin |
| Pin 27 | RA0 — I/O pin |
| Pin 28 | RA1 — I/O pin |
| Pin 29 | RB0 — I/O pin |
| Pin 30 | RB1 — I/O pin |
| Pin 31 | RB2 — I/O pin |
| Pin 32 | RB3 — I/O pin |
| Pin 33 | RB4 — I/O pin |
| Pin 34 | RB5 — I/O pin |
| Pin 35 | RB6 — I/O pin |
| Pin 36 | RB8 — I/O pin |
| Pin 37 | RB9 — I/O pin |
| Pin 38 | RB10 — I/O pin |
| Pin 39 | RB11 — I/O pin |
| Pin 40 | VSS — Ground |
| Pin 41 | VDD — Power supply |
| Pin 42 | RB12 — I/O pin |
| Pin 43 | RB13 — I/O pin |
| Pin 44 | RB14 — I/O pin |
| Pin 45 | RB15 — I/O pin |
| Pin 46 | RF0 — I/O pin |
| Pin 47 | RF1 — I/O pin |
| Pin 48 | RF2 — I/O pin |
| Pin 49 | RF3 — I/O pin |
| Pin 50 | RF4 — I/O pin |
| Pin 51 | RF5 — I/O pin |
| Pin 52 | RF6 — I/O pin |
| Pin 53 | RF7 — I/O pin |
| Pin 54 | VSS — Ground |
| Pin 55 | VDD — Power supply |
| Pin 56 | RG0 — I/O pin |
| Pin 57 | RG1 — I/O pin |
| Pin 58 | RE0 — I/O pin |
| Pin 59 | RE1 — I/O pin |
| Pin 60 | RE2 — I/O pin |
| Pin 61 | RE3 — I/O pin |
| Pin 62 | RE4 — I/O pin |
| Pin 63 | RE5 — I/O pin |
| Pin 64 | RE6 — I/O pin |
| Pin 65 | RE7 — I/O pin |
| Pin 66 | RG2 — I/O pin |
| Pin 67 | RG3 — I/O pin |
| Pin 68 | RC1 — I/O pin |
| Pin 69 | RC2 — I/O pin |
| Pin 70 | RC3 — I/O pin |
| Pin 71 | RC4 — I/O pin |
| Pin 72 | VSS — Ground |
| Pin 73 | VDD — Power supply |
| Pin 74 | RD0 — I/O pin |
| Pin 75 | RD1 — I/O pin |
| Pin 76 | RD2 — I/O pin |
| Pin 77 | RD3 — I/O pin |
| Pin 78 | RD4 — I/O pin |
| Pin 79 | RD5 — I/O pin |
| Pin 80 | RD6 — I/O pin |
| Pin 81 | RD7 — I/O pin |
| Pin 82 | RG12 — I/O pin |
| Pin 83 | RG13 — I/O pin |
| Pin 84 | RG14 — I/O pin |
| Pin 85 | RF8 — I/O pin |
| Pin 86 | RF9 — I/O pin |
| Pin 87 | RF10 — I/O pin |
| Pin 88 | RF11 — I/O pin |
| Pin 89 | RF12 — I/O pin |
| Pin 90 | VSS — Ground |
| Pin 91 | VDD — Power supply |
| Pin 92 | RF13 — I/O pin |
| Pin 93 | RA2 — I/O pin |
| Pin 94 | RA3 — I/O pin |
| Pin 95 | RA4 — I/O pin |
| Pin 96 | RA5 — I/O pin |
| Pin 97 | RA6 — I/O pin |
| Pin 98 | RA7 — I/O pin |
| Pin 99 | OSC1 — Crystal oscillator input |
| Pin 100 | OSC2 — Crystal oscillator output |
Typische Anwendungen
PIC32MX170F512L-I/PT ist geeignet für 6 Anwendungs: USB Audio Headset / Sound Card, HMI Panel with Graphics LCD, Industrial CAN Node, Capacitive Touch Keypad, USB Barcode / Magnetic-Stripe Reader, IoT Sensor Aggregator.
USB Audio Headset / Sound Card
The PIC32MX170F512L-I/PT's combination of Full-Speed USB 2.0 On-The-Go and two I2S ports makes it well suited for USB-to-I2S audio interfaces, including headsets, USB DACs, and USB microphones. The 50 MHz MIPS32 M4K core sustains 83 DMIPS, sufficient for sample-rate conversion and volume control at 48 kHz/24-bit; it issues two ANSI/USB audio class commands. The two I2S lanes support independent stereo paths for headphone and line outputs. The I2S interface pairs naturally with the PIC32MX270F512L-I/PT for higher sample rates.
Empfohlen
HMI Panel with Graphics LCD
The PIC32MX170F512L-I/PT integrates a Parallel Master Port (PMP) with dual read/write buffers, enabling direct connection to small graphics LCDs without an external frame buffer. The 100-pin TQFP gives enough I/O to run an 8/16-bit PMP bus plus mTouch capacitive touch channels for buttons. The 83 DMIPS performance is enough to draw 4-bpp widgets and handle UI state machines. PMP timing is programmable and matches common 320x240 QVGA panels.
Empfohlen
Industrial CAN Node
The PIC32MX170F512L-I/PT pairs its CAN 2.0B controller with five UART and PMP, fitting industrial CAN nodes that need a sensor bridge or small HMI. The 50 MHz MIPS32 M4K core runs CANopen and DeviceNet stacks without burden; the industrial -40C to +85C rating and 100-pin TQFP give sufficient GPIO for parallel digital inputs. An external CAN transceiver such as MCP2551 or TJA1050 is required. PIC32MX270F512L-I/PT is the higher-throughput upgrade.
Empfohlen
Capacitive Touch Keypad
Microchip's mTouch library and CTMU peripheral let the PIC32MX170F512L-I/PT implement capacitive touch sensing for human-machine interfaces. The 16 ADC channels and CTMU provide up to 16 touch buttons or a 4x4 matrix with proximity detection, suitable for appliances, door locks, and consumer devices. The 100-pin TQFP brings ample I/O for shared LED scanning, and PPS lets you remap sensor channels to any spare pin.
Empfohlen
USB Barcode / Magnetic-Stripe Reader
The PIC32MX170F512L-I/PT's USB OTG and 512 KB Flash are sized for embedded USB peripherals such as barcode scanners, magnetic-stripe readers, and RFID HID bridges. The PIC32MX USB stack handles HID/CDC/MSD classes; the dual I2S ports are unused, freeing them for diagnostic logging. The -40C to +85C industrial range covers retail and warehouse environments. PIC32MX170F512L-50I/PT is the speed-graded equivalent.
Empfohlen
IoT Sensor Aggregator
The PIC32MX170F512L-I/PT acts as a sensor aggregator: it pulls data over UART/I2C/SPI from environmental or motion sensors and forwards it via USB, CAN, or a wireless module on a UART. The 50 MHz MIPS32 M4K core, 64 KB RAM, and PPS flexibility support multiple serial buses simultaneously. mTouch/CTMU and the 16-channel ADC add analog and capacitive front-ends. PIC32MX270F512L-I/PT is the higher-speed IoT gateway upgrade.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für PIC32MX170F512L-I/PT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | PIC32MX170F512L-I/PF | PIC32MX170F512HT-50I/PT | PIC32MX270F512L-I/PT | PIC32MX170F512L-50I/PT |
|---|---|---|---|---|---|
| Package | 100-pin TQFP (PT) 12x12 mm | 100-pin TQFP (PF) 14x14 mm - same silicon, different footprint | 100-pin TQFP (PT) 12x12 mm - same | 100-pin TQFP (PT) 12x12 mm - same | 100-pin TQFP (PT) 12x12 mm - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum CPU Clock | 50 MHz (83 DMIPS) | 50 MHz | 50 MHz | 120 MHz - 140% higher | 50 MHz |
| Flash Memory | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB |
| SRAM | 64 KB | 64 KB | 64 KB | 64 KB | 64 KB |
| USB | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 HS OTG + host - upgrade | USB 2.0 FS OTG |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Parametric Match | 100 (baseline) | 90 - identical silicon, larger PCB land pattern | 100 - identical silicon, tape-and-reel packaging | 95 - higher CPU, higher USB, same memory/peripherals | 100 - identical silicon, speed-graded |
Wichtigste Unterscheidungsmerkmale
- Highest pin count in PIC32MX1XX/2XX/5XX family with PMP, USB OTG, and CAN (vs. PIC32MX170F256B-I/SS)
- Drop-in 120 MHz performance upgrade path (vs. PIC32MX270F512L-I/PT)
- 512 KB Flash vs 256 KB Flash at same price tier (vs. PIC32MX170F256L-I/PT)
Designhinweise
The PIC32MX170F512L-I/PT integrates a 1.8 V core LDO. Decoupling must include a 100 nF ceramic on each AVDD/VDD pin pair and a bulk 4.7 uF on VDDCORE. If USB is enabled, VUSB_3V3 must be tied to VDD through a ferrite bead to avoid back-drive; USB bus-powered designs need a 5V-tolerant source (Microchip ANSLU610). Estimated VDDIC quiescent is approximately 15-25 mA at 50 MHz with full peripheral toggle, so keep an external LDO headroom of at least 250 mA for USB hot-plug.
Route the USB D+/D- differential pair with 90 ohm differential impedance and a maximum length of 50 mm. The 12 MHz crystal traces should be short and symmetric, with the load capacitors placed as close to the OSC1/OSC2 pins as possible. For PMP-driven graphics LCDs, place the panel connector next to the PMP pins (RE0-RE7, RD0-RD7, RG2-RG3) to avoid bus turnaround issues at 25 MHz.
Peripheral Pin Select (PPS) is not available on every pin; the datasheet pinout specifies which pins are input-only vs output-only remappable. Designers often forget that PPS remap assignments are unlocked via CFGCON, and that mappable pins default to GPIO at reset. Avoid using RG6-RG9 as remapped outputs since they are 5V-tolerant only and can conflict with JTAG/ICSP programming pins. Always verify the 100-pin TQFP pinout versus the part marking '-I/PT'.
The PIC32MX170F512L-I/PT's I/O drive strength is rated at 10 mA source/sink, with low-current option of 5 mA. For SPI/I2C buses that are heavily loaded, enable slew-rate limiting by clearing the SRCRE bit on the relevant port. The CTMU-driven mTouch inputs should be guarded with a 100 ohm ferrite to reduce coupled noise from PWM outputs.
Compliance-Informationen
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified - this is a general-purpose MCU. For automotive applications, choose PIC32MX170F512LT-I/EF or consult Microchip automotive-grade PIC32MX portfolio.