SN65175D - Quad Differential Receiver | Texas Instruments
Teilenummer: SN65175D ✓ AktivSN65175D Übersicht
A differential line receiver converts a pair of differential input signals into one logic-level output. In the signal path, receiver ICs > differential line receivers > interface ICs > semiconductors, this function supports communication between physically separated equipment while rejecting common-mode noise. The SN65175D is designed for multipoint bus transmission over long lines in noisy industrial environments.
Four independent receiver channels provide efficient termination of RS-422 or RS-485 links. The 3-state outputs allow multiple receivers to share a bus when required, while the 50 mV hysteresis helps prevent output chatter around a transition threshold. Its 4.75 V to 5.25 V supply range is compatible with conventional 5 V interface systems. The 16-pin SOIC package supports standard surface-mount assembly and PCB layout practices.
The device is designed to meet ANSI EIA/TIA-422-B, RS-423-B, and RS-485 requirements and ITU V.10, V.11, X.26, and X.27 recommendations. Its common-mode input-voltage handling extends to at least -12 V, helping the receiver tolerate voltage offsets between connected systems while the differential signal remains within the valid transition region. Each receiver provides a separate logic output, allowing four bus channels to be handled by one package.
Typical uses include industrial RS-485 multidrop networks, factory automation equipment, test and measurement systems, and point-to-point RS-422 links. The SN65175D can also serve as the receive section of a communication subsystem where four isolated or non-isolated channels must share a common logic interface. The lack of integrated isolation means the system designer must address ground-potential differences through cable routing, protection, or external isolation methods.
PCB implementation should preserve the differential signal path from each receiver pair to the IC, minimize unequal routing between the positive and negative inputs, and provide termination at the appropriate physical ends of the bus. Connectors, protection networks, and cable transients must be evaluated independently because the receiver's common-mode range does not replace surge protection.
This page adds application-focused implementation guidance, lifecycle context, drop-in replacement analysis, and side-by-side interface comparisons. It is intended to help engineers determine whether the SN65175D's channel count, logic interface, package, and electrical ratings match an existing RS-422 or RS-485 design before placing a replacement order.
Drop-in-Alternativen für SN65175D – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit SN65175D (gleiche Bauform und Footprint) – abweichend in Mounting Type, Output State, Package, Receiver Type.
SN75175N
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →SN75LBC175D
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
SN65LBC173AMDREP
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
SN65175D Technische Daten
| Receiver Type | Quadruple differential line receiver |
| Number of Receivers | 4 receivers |
| Number of Drivers | 0 drivers |
| Supported Protocols | RS-422, RS-423, RS-485 |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Receiver Hysteresis | 50 mV |
| Output State | 3-state |
| Betriebstemperaturbereich | -40 °C to 85 °C |
| Gehäuse | SOIC (D), 16 pins |
| Package Dimensions | 9.9 mm × 6 mm |
| Package Area | 59.4 mm² |
| Montageart | Surface mount |
| ANSI Standards | EIA/TIA-422-B, RS-423-B, RS-485 |
| ITU Recommendations | V.10, V.11, X.26, X.27 |
SN65175D 59.4 mm² Pinbelegungsleitfaden
Pinbelegung für SN65175D (59.4 mm²-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für SN65175D.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
SN65175D ist geeignet für 6 Anwendungs: Industrial RS-485 Multidrop Networks, Point-to-Point RS-422 Data Links, Test and Measurement Equipment, Factory Automation Control Interfaces, Data Acquisition and Sensor Interfaces, Legacy Equipment Communication Retrofit.
Industrial RS-485 Multidrop Networks
The SN65175D fits the receive portion of industrial RS-485 multidrop networks because it combines four differential receivers with 50 mV hysteresis, 3-state outputs, and an operating supply range of 4.75 V to 5.25 V. Place it at the receiving end of a bus segment to convert four differential pairs into digital logic signals for a controller. Its common-mode input capability extends to at least -12 V, which supports systems with voltage offsets between connected equipment. The circuit still needs an external RS-485 driver, termination at the physical bus ends, surge protection, and a careful grounding strategy. Designers should maintain matched routing between each positive and negative receiver input and verify cable length against the selected data rate.
Empfohlen
Point-to-Point RS-422 Data Links
The SN65175D is appropriate for point-to-point RS-422 links that need up to four receiving channels and a 5 V logic interface. Each differential receiver rejects common-mode noise while generating a logic output for the receiving logic, making the device suitable for equipment interconnects, data acquisition links, and remote-control interfaces. The 4.75 V to 5.25 V supply range supports conventional 5 V systems, while the 3-state outputs can provide a controlled inactive state where multiple receiver outputs share a bus. The implementation should preserve short, symmetric differential traces and use the receiver input ratings to select cable termination. The SN65175D contains no transmitter or galvanic isolation, so an external driver and separate isolation strategy remain necessary.
Empfohlen
Test and Measurement Equipment
The SN65175D is useful in test and measurement equipment that receives differential commands or status signals from remote fixtures. Its four receiver channels reduce the number of interface packages needed when several low-speed buses terminate at an instrument, while the 50 mV hysteresis helps maintain stable logic states when the differential signal is close to a transition threshold. The receiver can operate with 4.75 V to 5.25 V logic, matching many legacy acquisition and control platforms. Designers should keep input and return paths together, provide grounding that does not create additional cable-current loops, and avoid assuming that a logic receiver replaces input surge protection. Firmware and hardware revisions should record the receiver thresholds used during interoperability testing.
Empfohlen
Factory Automation Control Interfaces
The SN65175D can support factory automation control interfaces that combine several RS-485 or RS-422 links with a central controller. Four differential receivers permit multiple field buses or device banks to feed one logic domain, and the device's -40 °C to 85 °C operating range covers many industrial environments. The receiver's common-mode input range extending to at least -12 V improves tolerance of grounded differences between industrial cabinets, although the complete system still needs surge and ESD protection. Use symmetrical PCB routing for each differential pair, avoid stubs, and terminate only at the designated ends of the bus. A separate transceiver is required for command transmission, and isolation should be added where safety standards or ground-potential limits require it.
Empfohlen
Data Acquisition and Sensor Interfaces
The SN65175D can act as the digital receiving stage of a data-acquisition front end when sensors or remote transducer assemblies transmit differential signals over RS-422 or RS-485. Four channels allow compact aggregation of several measurement links before data reaches an ADC, FPGA, or microcontroller. Its 50 mV hysteresis helps suppress repetitive output transitions around a threshold, while the 4.75 V to 5.25 V operating range supports established 5 V acquisition electronics. Signal integrity depends on controlled source impedances, correct cable termination, and equal routing between differential inputs. The device does not amplify small sensor signals directly, so low-level analog conditioning remains upstream. Verify ground offsets and transient exposure for each installation environment rather than assuming the receiver alone provides industrial robustness.
Empfohlen
Legacy Equipment Communication Retrofit
The SN65175D is a practical choice when maintaining or retrofitting legacy equipment that uses a 16-pin SOIC footprint for four RS-422, RS-423, or RS-485 receiver channels. It offers a 5 V supply range, 50 mV hysteresis, and 3-state outputs while remaining a receiver-only device with no integrated drivers. A modernization project should compare the new and original receiver pinouts, input thresholds, output timing, and common-mode limits before installation. Preserving the existing footprint reduces board changes, but it does not remove the need to verify trace impedances, connector protection, and logic levels. The current active TI listing supports procurement planning, but obsolete-grade, availability, and obsolescence checks for the originally installed part should be completed separately.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für SN65175D – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | SN75175N | SN75LBC175D | SN65LBC173AMDREP |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOIC-16 | SOIC-16 - same | SOIC-16 - same | SOIC-16 - same |
| Receiver Type | Quadruple differential line receiver | Quadruple differential line receiver | Differential line receiver | Differential line receiver |
Wichtigste Unterscheidungsmerkmale
- Four receiving channels in one 16-pin package (vs. SN65LBC173AMDREP)
- Three-state receiver outputs for shared-bus control (vs. SN75LBC175D)
- Documented 5 V interface range (vs. SN75175N)
- Multipoint and noisy-environment positioning (vs. SN65LBC173AMDREP)
Designhinweise
Route each differential receiver pair as a tightly coupled pair with equal trace lengths, geometry, and reference-plane transitions. Place the IC near the connector or protection network to minimize the distance over which cable transients can propagate into the device. Avoid sharing a narrow return path between multiple pairs because differential signals rely on a defined return reference. Check the receiver footprint and pin-1 orientation against the manufacturer's package drawing before releasing artwork.
Do not treat the SN65175D as a complete RS-485 transceiver: it contains zero drivers and four receivers. Use a separate compatible line driver for transmission, and place termination only at the physical ends of the bus. Also verify that every receiver input remains within its common-mode voltage range during startup, shutdown, and fault conditions. The 50 mV hysteresis reduces chatter but does not correct an improperly balanced cable, excessive ground offset, or inadequate surge protection.
Decouple the 5 V supply close to the SN65175D and keep the return connection compact. The device requires a 4.75 V to 5.25 V operating supply, so routing drops and supply ripple must remain within that range at the package pins. Place bulk and high-frequency decoupling according to the manufacturer's recommended circuit and the interface's switching activity. If multiple bus channels operate simultaneously, verify the total supply-current margin rather than sizing the rail for one channel.
For a replacement on an existing PCB, compare the original and candidate devices at the pin level rather than matching the package outline alone. Verify power and ground pins, differential input polarity, output-enable polarity, receiver thresholds, common-mode limits, propagation delay, and 3-state behavior. The SN75175N, SN75LBC175D, and SN65LBC173AMDREP are candidates for engineering review, but each requires confirmation against its manufacturer datasheet before being treated as a guaranteed drop-in substitute.
Compliance-Informationen
The interface-focused SN65175D is not presented as an automotive-qualified AEC-Q100 device. Obtain the current manufacturer material-compliance declarations before a regulated production release.