Texas Instruments

SN65175D - Quad Differential Receiver | Texas Instruments

MPN: SN65175D ✓ Aktif
4.75 V to 5.25 V Vdss EIA/TIA-422-B, RS-423-B, RS-485 Rds(on) SOIC (D), 16 pins Package
MOQ: 1 |

SN65175D Ringkasan

The Texas Instruments SN65175D is a quadruple differential line receiver with four receivers, 3-state outputs, and support for RS-422, RS-423, and RS-485 interfaces. It operates from a 4.75 V to 5.25 V supply, provides 50 mV receiver hysteresis, and is packaged in a 16-pin SOIC (D) measuring 9.9 mm by 6 mm.

A differential line receiver converts a pair of differential input signals into one logic-level output. In the signal path, receiver ICs > differential line receivers > interface ICs > semiconductors, this function supports communication between physically separated equipment while rejecting common-mode noise. The SN65175D is designed for multipoint bus transmission over long lines in noisy industrial environments.

Four independent receiver channels provide efficient termination of RS-422 or RS-485 links. The 3-state outputs allow multiple receivers to share a bus when required, while the 50 mV hysteresis helps prevent output chatter around a transition threshold. Its 4.75 V to 5.25 V supply range is compatible with conventional 5 V interface systems. The 16-pin SOIC package supports standard surface-mount assembly and PCB layout practices.

The device is designed to meet ANSI EIA/TIA-422-B, RS-423-B, and RS-485 requirements and ITU V.10, V.11, X.26, and X.27 recommendations. Its common-mode input-voltage handling extends to at least -12 V, helping the receiver tolerate voltage offsets between connected systems while the differential signal remains within the valid transition region. Each receiver provides a separate logic output, allowing four bus channels to be handled by one package.

Typical uses include industrial RS-485 multidrop networks, factory automation equipment, test and measurement systems, and point-to-point RS-422 links. The SN65175D can also serve as the receive section of a communication subsystem where four isolated or non-isolated channels must share a common logic interface. The lack of integrated isolation means the system designer must address ground-potential differences through cable routing, protection, or external isolation methods.

PCB implementation should preserve the differential signal path from each receiver pair to the IC, minimize unequal routing between the positive and negative inputs, and provide termination at the appropriate physical ends of the bus. Connectors, protection networks, and cable transients must be evaluated independently because the receiver's common-mode range does not replace surge protection.

This page adds application-focused implementation guidance, lifecycle context, drop-in replacement analysis, and side-by-side interface comparisons. It is intended to help engineers determine whether the SN65175D's channel count, logic interface, package, and electrical ratings match an existing RS-422 or RS-485 design before placing a replacement order.

Alternatif penggantian untuk SN65175D — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian SN65175D (sama faktor bentuk dan footprint) — berbeda di dalam Mounting Type, Output State, Package, Receiver Type.

Texas Instruments
Mounting Type: Through-hole
Output State: Three-state output
Package: 16-pin plastic DIP (16-PDIP)
Bandingkan dengan SN65175D →

SN75175N

✅ Drop-In
Texas Instruments
📦 SOIC-16
Quad differential line receiver · 4 channels · 10 Mbit/s · 4.75 V to 5.25 V · 5 V · Three-state output · RS-485, RS-422, RS-423

Kontak untuk harga

Lihat Datasheet →

SN75LBC175D

✅ Drop-In
📦 SOIC-16
The differential receiver function is retained; receiver threshold, common-mode range, enable behavior, and timing differences require verification.

📋 Alternatif referensi (tidak dalam katalog)

SN65LBC173AMDREP

✅ Drop-In
📦 SOIC-16
Both provide a 16-pin SOIC differential receiver function, while supply, input thresholds, common-mode range, and logic timing may differ.

📋 Alternatif referensi (tidak dalam katalog)

SN65175D Spesifikasi

Receiver Type Quadruple differential line receiver
Number of Receivers 4 receivers
Number of Drivers 0 drivers
Supported Protocols RS-422, RS-423, RS-485
Supply Voltage Range 4.75 V to 5.25 V
Receiver Hysteresis 50 mV
Output State 3-state
Rentang Suhu Kerja -40 °C to 85 °C
Paket SOIC (D), 16 pins
Package Dimensions 9.9 mm × 6 mm
Package Area 59.4 mm²
Tipe Mounting Surface mount
ANSI Standards EIA/TIA-422-B, RS-423-B, RS-485
ITU Recommendations V.10, V.11, X.26, X.27

SN65175D 59.4 mm² Diamant Konfigurasi Panduan

Konfigurasi pin untuk SN65175D (59.4 mm² pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.

Diamant diagram pakai pakai 59.4 mm² untuk SN65175D

Tidak ada data diatribut pin yang tersedia untuk SN65175D.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

SN65175D cocok untuk 6 aplikasis: Industrial RS-485 Multidrop Networks, Point-to-Point RS-422 Data Links, Test and Measurement Equipment, Factory Automation Control Interfaces, Data Acquisition and Sensor Interfaces, Legacy Equipment Communication Retrofit.

🏭

Industrial RS-485 Multidrop Networks

The SN65175D fits the receive portion of industrial RS-485 multidrop networks because it combines four differential receivers with 50 mV hysteresis, 3-state outputs, and an operating supply range of 4.75 V to 5.25 V. Place it at the receiving end of a bus segment to convert four differential pairs into digital logic signals for a controller. Its common-mode input capability extends to at least -12 V, which supports systems with voltage offsets between connected equipment. The circuit still needs an external RS-485 driver, termination at the physical bus ends, surge protection, and a careful grounding strategy. Designers should maintain matched routing between each positive and negative receiver input and verify cable length against the selected data rate.

🌐

Point-to-Point RS-422 Data Links

The SN65175D is appropriate for point-to-point RS-422 links that need up to four receiving channels and a 5 V logic interface. Each differential receiver rejects common-mode noise while generating a logic output for the receiving logic, making the device suitable for equipment interconnects, data acquisition links, and remote-control interfaces. The 4.75 V to 5.25 V supply range supports conventional 5 V systems, while the 3-state outputs can provide a controlled inactive state where multiple receiver outputs share a bus. The implementation should preserve short, symmetric differential traces and use the receiver input ratings to select cable termination. The SN65175D contains no transmitter or galvanic isolation, so an external driver and separate isolation strategy remain necessary.

📺

Test and Measurement Equipment

The SN65175D is useful in test and measurement equipment that receives differential commands or status signals from remote fixtures. Its four receiver channels reduce the number of interface packages needed when several low-speed buses terminate at an instrument, while the 50 mV hysteresis helps maintain stable logic states when the differential signal is close to a transition threshold. The receiver can operate with 4.75 V to 5.25 V logic, matching many legacy acquisition and control platforms. Designers should keep input and return paths together, provide grounding that does not create additional cable-current loops, and avoid assuming that a logic receiver replaces input surge protection. Firmware and hardware revisions should record the receiver thresholds used during interoperability testing.

⚙️

Factory Automation Control Interfaces

The SN65175D can support factory automation control interfaces that combine several RS-485 or RS-422 links with a central controller. Four differential receivers permit multiple field buses or device banks to feed one logic domain, and the device's -40 °C to 85 °C operating range covers many industrial environments. The receiver's common-mode input range extending to at least -12 V improves tolerance of grounded differences between industrial cabinets, although the complete system still needs surge and ESD protection. Use symmetrical PCB routing for each differential pair, avoid stubs, and terminate only at the designated ends of the bus. A separate transceiver is required for command transmission, and isolation should be added where safety standards or ground-potential limits require it.

📡

Data Acquisition and Sensor Interfaces

The SN65175D can act as the digital receiving stage of a data-acquisition front end when sensors or remote transducer assemblies transmit differential signals over RS-422 or RS-485. Four channels allow compact aggregation of several measurement links before data reaches an ADC, FPGA, or microcontroller. Its 50 mV hysteresis helps suppress repetitive output transitions around a threshold, while the 4.75 V to 5.25 V operating range supports established 5 V acquisition electronics. Signal integrity depends on controlled source impedances, correct cable termination, and equal routing between differential inputs. The device does not amplify small sensor signals directly, so low-level analog conditioning remains upstream. Verify ground offsets and transient exposure for each installation environment rather than assuming the receiver alone provides industrial robustness.

🔧

Legacy Equipment Communication Retrofit

The SN65175D is a practical choice when maintaining or retrofitting legacy equipment that uses a 16-pin SOIC footprint for four RS-422, RS-423, or RS-485 receiver channels. It offers a 5 V supply range, 50 mV hysteresis, and 3-state outputs while remaining a receiver-only device with no integrated drivers. A modernization project should compare the new and original receiver pinouts, input thresholds, output timing, and common-mode limits before installation. Preserving the existing footprint reduces board changes, but it does not remove the need to verify trace impedances, connector protection, and logic levels. The current active TI listing supports procurement planning, but obsolete-grade, availability, and obsolescence checks for the originally installed part should be completed separately.

Ringkasan Produk Direkomendasikan

MC74F243M onsemi Digunakan di dalam: Industrial RS-485 Multidrop Networks, Point-to-Point RS-422 Data Links, Test and Measurement Equipment, Factory Automation Control Interfaces, Data Acquisition and Sensor Interfaces SN75175N Texas Instruments Digunakan di dalam: Industrial RS-485 Multidrop Networks, Factory Automation Control Interfaces, Legacy Equipment Communication Retrofit SN75LBC175D Alternative differential line receiver Digunakan di dalam: Point-to-Point RS-422 Data Links, Data Acquisition and Sensor Interfaces SN65LBC173AMDREP Related low-power differential receiver candidate Digunakan di dalam: Test and Measurement Equipment, Legacy Equipment Communication Retrofit
What is the SN65175D?
The SN65175D is a Texas Instruments quadruple differential line receiver with four receiver channels, 3-state outputs, and support for RS-422, RS-423, and RS-485 interfaces. According to the TI product page, it operates from 4.75 V to 5.25 V and is intended for multipoint bus transmission over long lines in noisy environments. The device is packaged in a 16-pin SOIC (D). Its four-channel arrangement is useful when a system needs several differential bus inputs connected to a common digital interface.
What are the key specifications of SN65175D that engineers should know?
The SN65175D combines four differential receivers, a 4.75 V to 5.25 V supply range, 50 mV receiver hysteresis, and 3-state outputs in a 16-pin SOIC package. According to the TI product page, it is designed to meet ANSI EIA/TIA-422-B, RS-423-B, and RS-485 requirements, as well as ITU V.10, V.11, X.26, and X.27 recommendations. Its operating temperature range is -40 °C to 85 °C, and its common-mode input-voltage range extends to at least -12 V.
Where can I download the SN65175D datasheet PDF?
The SN65175D manufacturer datasheet and ordering information are available through the official Texas Instruments SN65175 product page at https://www.ti.com/product/SN65175. The product page identifies the SN65175D as a quadruple differential receiver in a 16-pin SOIC (D) package. It also provides the device description, supported interface standards, and ordering details. For an exact PDF revision suitable for design release, use the datasheet link displayed on TI's official product page rather than a third-party document mirror.
Where can I find the SN65175D pinout?
Use the pin-description table and package drawing in the SN65175D manufacturer datasheet for authoritative pin assignments. The TI product page identifies the package as a 16-pin SOIC (D), confirming the physical pin count and body size of 9.9 mm by 6 mm. The complete pin numbering and signal names should be transcribed directly from the datasheet because a receiver input, enable input, ground, and power pins must be assigned exactly as specified. The package image linked from this page is a footprint aid rather than a substitute for the manufacturer pin table.
What is the operating voltage of SN65175D?
The SN65175D operates from 4.75 V to 5.25 V. According to the Texas Instruments product page and the component specifications, this is a conventional 5 V differential line receiver supporting RS-422, RS-423, and RS-485 interfaces. The specified supply range leaves design margin around a nominal 5 V rail while requiring the PCB power network to remain within the published operating limits. Logic output levels and input thresholds should be evaluated against the system supply and interface requirements rather than inferred solely from the nominal supply voltage.
Is the SN65175D suitable for RS-485 industrial networks?
The SN65175D is suitable for the receive function in RS-485 industrial networks because it provides four differential receivers, 50 mV hysteresis, 3-state outputs, and a common-mode input range extending to at least -12 V. According to TI's product description, it is designed for multipoint transmission on long bus lines in noisy environments. It does not include a driver, so the system still requires a separate compatible line driver, appropriate bus termination, connector protection, and an analysis of grounding and surge conditions.
What can replace the SN65175D?
The SN75175N is the closest documented same-brand replacement candidate because it is also identified as a quadruple differential line receiver with 3-state outputs for RS-422, RS-423, and RS-485 operation. The SN75LBC175D is another receiver-focused candidate found in cross-reference data. A replacement should not be selected solely by function: confirm the 16-pin SOIC footprint, pin assignments, supply range, receiver thresholds, common-mode limits, output-enable behavior, and lifecycle status against the manufacturer datasheet before modifying an existing board.
Is the SN65175D the same as the SN75175N?
The SN65175D and SN75175N are closely related in function, but they are not automatically interchangeable from the available information. Both are described as quadruple differential line receivers supporting RS-422, RS-423, and RS-485, and both use 3-state outputs. According to the cross-reference information, their functional roles are similar. The SN65175D is a 16-pin SOIC (D), while the exact package and every pin assignment for the SN75175N must be confirmed before treating it as a drop-in replacement.
What is the best Texas Instruments equivalent for SN65175D?
The SN75175N is the leading same-brand equivalent candidate because it is a quadruple differential line receiver with the same RS-422, RS-423, and RS-485 orientation and 3-state output function. The SN75LBC175D is a secondary candidate identified by comparison data. Neither candidate should be treated as a guaranteed drop-in replacement until its 16-pin SOIC pinout, supply requirements, input thresholds, common-mode range, and output timing are checked against the original design. TI's cross-reference search can confirm current official equivalency.
When should I choose SN65175D over SN75175N?
Choose the SN65175D when a design specifically requires the manufacturer's 16-pin SOIC (D) SN65175 qualification, its documented 4.75 V to 5.25 V supply range, or an exact existing-board replacement. The SN75175N is a reasonable functional alternative for a new quadruple differential receiver design after its complete electrical and pin data are verified. For an installed board, matching the package drawing, pin names, enable logic, and package suffix is more important than the shared RS-485 description.
Is SN65175D better than SN75LBC175D for a new design?
The SN65175D is the better-supported choice for preserving an existing TI SN65175 design because its package, supply range, interface standards, hysteresis, and operating-temperature details are published on the official product page. The SN75LBC175D may offer a different implementation or feature balance, but the cross-reference material does not establish every electrical detail needed for a direct substitution. Compare input thresholds, common-mode range, output-enable timing, propagation delay, supply current, and pinout before selecting it for a new design.
Is SN65175D in stock and what is its lead time?
Current inventory and lead time should be requested through the Request a Quote form on this page because stock changes by quantity, carrier option, and purchasing date. The official TI part-details result lists the SN65175D as active and identifies a tube carrier option with a package quantity of 40, but that status does not establish current warehouse stock. Request the quantity, target date, and required carrier configuration when asking for a quotation so the supplier can confirm allocation and delivery.
Where can I buy SN65175D online?
Use the Request a Quote form on this page to request SN65175D availability, commercial terms, and current lead time for the required quantity. The TI product-details information identifies the device as active in a 16-pin SOIC (D) package and lists tube packaging, while other catalog listings show the same device in standard 16-SOIC form. Confirm the exact package suffix, carrier configuration, production status, and quantity before releasing a purchase order.
How much does SN65175D cost?
The current SN65175D commercial price should be obtained through the Request a Quote form on this page because quotation results can depend on quantity, carrier option, market conditions, and supply availability. No static unit price should be used for budgeting because it can become stale. Include the target order quantity, acceptable tube or reel configuration, production volume, and required delivery date in the request to obtain a usable quotation.
Does SN65175D meet RoHS and REACH requirements?
The RoHS and REACH status must be confirmed from the current manufacturer product documentation and declarations before a regulated production release. The TI product page establishes the SN65175D's interface features, 4.75 V to 5.25 V supply range, -40 °C to 85 °C operating range, and 16-pin SOIC package, but the available product information does not state the compliance results. Ask the supplier for the applicable manufacturer material-compliance declaration and document its revision in the product file.

Data referensi engineering untuk SN65175D — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the SN65175D when an existing design requires a TI receiver-only IC with four RS-422, RS-423, or RS-485 channels, a 16-pin SOIC footprint, 50 mV hysteresis, and a 4.75 V to 5.25 V supply. It is especially suitable for industrial or test systems that already provide a separate line driver and require common-mode tolerance extending to at least -12 V. Consider the SN75175N for a new design when its detailed thresholds, timing, and pin assignments have been verified against the intended application. Evaluate the SN75LBC175D when its enable and fail-safe behavior match the system requirements. Treat the SN65LBC173AMDREP as a lower-confidence candidate whose supply, thresholds, common-mode limits, and timing require direct comparison. For all candidates, verify the exact footprint, input polarity, output-enable polarity, current consumption, and lifecycle status before approving a drop-in substitution.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini SN75175N SN75LBC175D SN65LBC173AMDREP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package SOIC-16 SOIC-16 - same SOIC-16 - same SOIC-16 - same
Receiver Type Quadruple differential line receiver Quadruple differential line receiver Differential line receiver Differential line receiver

Diferensiator Kunci

  • Four receiving channels in one 16-pin package (vsSN65LBC173AMDREP)
  • Three-state receiver outputs for shared-bus control (vsSN75LBC175D)
  • Documented 5 V interface range (vsSN75175N)
  • Multipoint and noisy-environment positioning (vsSN65LBC173AMDREP)

Catatan Desain

Route each differential receiver pair as a tightly coupled pair with equal trace lengths, geometry, and reference-plane transitions. Place the IC near the connector or protection network to minimize the distance over which cable transients can propagate into the device. Avoid sharing a narrow return path between multiple pairs because differential signals rely on a defined return reference. Check the receiver footprint and pin-1 orientation against the manufacturer's package drawing before releasing artwork.

Do not treat the SN65175D as a complete RS-485 transceiver: it contains zero drivers and four receivers. Use a separate compatible line driver for transmission, and place termination only at the physical ends of the bus. Also verify that every receiver input remains within its common-mode voltage range during startup, shutdown, and fault conditions. The 50 mV hysteresis reduces chatter but does not correct an improperly balanced cable, excessive ground offset, or inadequate surge protection.

Decouple the 5 V supply close to the SN65175D and keep the return connection compact. The device requires a 4.75 V to 5.25 V operating supply, so routing drops and supply ripple must remain within that range at the package pins. Place bulk and high-frequency decoupling according to the manufacturer's recommended circuit and the interface's switching activity. If multiple bus channels operate simultaneously, verify the total supply-current margin rather than sizing the rail for one channel.

For a replacement on an existing PCB, compare the original and candidate devices at the pin level rather than matching the package outline alone. Verify power and ground pins, differential input polarity, output-enable polarity, receiver thresholds, common-mode limits, propagation delay, and 3-state behavior. The SN75175N, SN75LBC175D, and SN65LBC173AMDREP are candidates for engineering review, but each requires confirmation against its manufacturer datasheet before being treated as a guaranteed drop-in substitute.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The interface-focused SN65175D is not presented as an automotive-qualified AEC-Q100 device. Obtain the current manufacturer material-compliance declarations before a regulated production release.

Data disahkan pada: 2026-11-09 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

sn65175d datasheet SN65175D datasheet pdf SN65175D pinout SN65175D equivalent SN65175D replacement SN65175D cross reference SN65175D vs SN75175N SN65175D 16-SOIC footprint SN65175D RS-485 receiver SN65175D industrial interface SN65175D price SN65175D stock

Komponen dan Istilah Terkait

Texas Instruments SN65175D SN75175N SN75LBC175D SN65LBC173AMDREP quad differential line receiver differential receiver RS-422 RS-423 RS-485 interface IC semiconductor 3-state output receiver hysteresis common-mode input voltage multipoint bus ANSI EIA/TIA-422-B ITU V.10 ITU V.11 SOIC-16 SOIC package family surface-mount package industrial automation test and measurement data acquisition
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ