Texas Instruments

SN74AC241N - 8-Channel 3-State Buffer | Texas Instruments

Teilenummer: SN74AC241N ✓ Aktiv
2 V to 6 V Vdss 20-pin PDIP (N) Package
MOQ: 1 |

SN74AC241N Übersicht

Texas Instruments SN74AC241N is an eight-channel, non-inverting CMOS buffer with independently controlled 3-state outputs, a 2 V to 6 V operating supply range, and a 20-pin PDIP package. The device is organized as two 4-bit buffer elements and is intended for bus-oriented receivers, transmitters, memory-address drivers, and clock-driver applications. According to the TI product page, the SN74AC241 family supports a -40 °C to 85 °C operating-temperature range for the N package.

A logic buffer is a digital semiconductor that reproduces an input signal at an output while providing buffering between a source and the next circuit stage. The 74AC family belongs to the advanced CMOS logic hierarchy, combining low-power operation with balanced drive capability and relatively high input impedance. In the SN74AC241, the tri-state output function allows each group of four outputs to be placed in a high-impedance state, preventing a disabled driver from actively driving a shared bus.

The principal feature is independent output-enable control, allowing two 4-bit sections to be enabled or disabled separately. The non-inverting architecture preserves input logic polarity. Operation from 2 V to 6 V supports both 3.3 V and 5 V systems, while the maximum input voltage of 6 V provides tolerance for supply-transient conditions. The exact propagation-delay, output-current, input-current, and static-power values are not stated in the retrieved product information and must be confirmed in the manufacturer datasheet before timing, fanout, or signal-integrity calculations.

SN74AC241N is a bus-oriented octal buffer rather than a general-purpose open-collector transceiver. Unlike a bidirectional transceiver, its data paths are unidirectional, and unlike a conventional non-3-state buffer, each four-output bank can be disabled. This makes the device appropriate when a controller, memory interface, or peripheral must be isolated from a shared bus while preserving standard logic levels. The N suffix identifies the through-hole PDIP package; board layout, insertion, and rework requirements therefore differ from surface-mount alternatives.

Typical uses include address-line buffering between a memory controller and external memory, clock distribution into bus loads, isolation of peripherals from shared data buses, and buffering of control signals in modular industrial equipment. Because the device supports 3-state outputs, firmware or external logic can determine which bank drives a shared bus. Designers should still verify timing against the worst-case load and trace capacitance shown in the manufacturer datasheet rather than assuming performance from the family name alone.

Decoupling and signal-integrity practice remain important in high-speed systems. Place the supply bypass capacitor close to the device, provide a continuous return path for output-current transients, and keep enable traces away from sensitive analog paths. Do not enable a bank while two outputs contend on the same bus unless the downstream system explicitly supports bus contention. Confirm that the selected source and destination devices meet the AC family voltage, temperature, and timing limits before using the buffer as an interface between unrelated logic families.

This product page combines the manufacturer ordering information with practical bus-isolation guidance, verified package details, and a parameter-by-parameter replacement comparison. It also highlights the distinctions that matter during PCB design: the PDIP-20 footprint, independent 3-state enable control, unidirectional non-inverting operation, and the need to validate exact timing and drive-current limits against the selected system load.

Drop-in-Alternativen für SN74AC241N – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

SN74AC241NE4

✅ Drop-In
📦 20-pin PDIP (N)
Same 2 V to 6 V octal 3-state buffer function and 20-pin PDIP footprint; ordering-code and qualification details should be confirmed.

📋 Referenzalternative (nicht im Katalog)

SN74AC241N Grenzwerte & elektrische Eigenschaften

Product Type Octal non-inverting buffer/line driver
Logic Family 74AC CMOS
Number of Channels 8 channels
Number of Buffer Elements 2 elements
Bits per Element 4 bits per element
Ausgangstyp 3-state output
Logic Polarity Non-inverting
Supply Voltage Range 2 V to 6 V
Maximum Input Voltage 6 V
Technology CMOS
Package Type 20-pin PDIP (N)
Anzahl der Pins 20 pins
Montageart Through-hole
Betriebstemperaturbereich -40 °C to 85 °C
Automotive Qualification Qualified for automotive applications to 6 V VCC operation
Output Enable Control Independent control for two 4-bit output banks

SN74AC241N 20-pin pdip (n) Pinbelegungsleitfaden

Pinbelegung für SN74AC241N (20-pin pdip (n)-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.

Pinbelegungsdiagramm für SN74AC241N im 20-pin pdip (n)-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für SN74AC241N.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

SN74AC241N ist geeignet für 6 Anwendungs: Memory Address Buffering, Shared Data-Bus Isolation, Clock Distribution, Industrial Control Interface, Test and Measurement Equipment, Peripheral Interface Buffering.

🖥️

Memory Address Buffering

The SN74AC241N fits between a memory controller and shared address lines because it provides eight non-inverting buffer channels divided into two independently controlled 4-bit banks. Each bank can be placed in a high-impedance state when it must not drive a bus, helping prevent contention during address multiplexing or memory-bank isolation. Its 2 V to 6 V operating range supports 3.3 V and 5 V systems, while the N package provides a conventional 20-pin PDIP footprint. Confirm propagation delay, output-current capability, and load capacitance in the manufacturer datasheet for the selected clock rate.

🌐

Shared Data-Bus Isolation

The SN74AC241N can isolate one group of four bus drivers while another group remains active, allowing peripheral data to share a common bus without every driver remaining connected. Its non-inverting, 3-state outputs preserve the source logic level and support selective participation in a bus-oriented system. The 2 V minimum supply permits operation in low-voltage CMOS logic environments, while the 6 V maximum supports 5 V rails. Use decoded output-enable logic and ensure all possible power-up, reset, and fault states prevent two devices from driving the same node simultaneously.

🏭

Clock Distribution

The SN74AC241N can buffer a clock into separate four-channel sections and disconnect a section when it is not needed. This makes it useful for modular backplanes, industrial controllers, and test equipment where clock loads must be isolated to reduce capacitive loading or avoid unwanted drive paths. Because the device is specified for clock-driver use, it provides a direct functional match for this application. The usable frequency must be checked against worst-case propagation delay, output loading, and supply voltage, and enable transitions should be synchronized with the system timing plan.

🏭

Industrial Control Interface

The SN74AC241N suits industrial control boards that separate local logic from external bus connectors or field-routing circuits. Two independent output banks provide selective isolation, and the through-hole 20-pin PDIP package is convenient for prototypes, repairable assemblies, and designs assembled through manual insertion. Its 2 V to 6 V supply range accommodates common industrial logic levels, while the -40 °C to 85 °C N-package range supports a broad operating environment. Layout review should include bus-length limits, surge requirements, grounding, and separation between sensitive control nodes and connector routing.

🔧

Test and Measurement Equipment

In test and measurement equipment, the SN74AC241N can buffer control, address, or fixture-control lines while keeping unused drivers electrically disconnected. The independent 3-state sections make it practical to route several instrument functions through a shared backplane without permanent contention. Its CMOS implementation and 2 V to 6 V operating range suit low-voltage digital control systems, while the PDIP package simplifies retrofit and repair. Validate timing over the complete operating-temperature range and verify that connected fixtures do not exceed the device's specified output-current and capacitive-load limits.

🧩

Peripheral Interface Buffering

The SN74AC241N is appropriate between a controller and a peripheral bus when the peripheral must be disconnected during reset, programming, or bus sharing. Eight non-inverting channels preserve data and control semantics, while two output-enable groups provide coarse isolation control. The device operates at 2 V to 6 V and is intended for bus-oriented receivers and transmitters, giving it a natural fit for CMOS peripheral interfaces. A complete design should include defined enable states, adequate supply bypassing, and timing checks for every bus transition to prevent contention or marginal data setup.

Zusammenfassung der empfohlenen Produkte

SN74AC241NE4 Same-buffer alternative with the same PDIP package Verwendet in: Memory Address Buffering, Shared Data-Bus Isolation, Clock Distribution, Industrial Control Interface, Test and Measurement Equipment, Peripheral Interface Buffering SN74AC244NE4 Related octal 3-state buffer family requiring polarity review Verwendet in: Memory Address Buffering, Shared Data-Bus Isolation, Clock Distribution, Test and Measurement Equipment, Peripheral Interface Buffering MC74ACT05NG Related 20-pin logic device whose pin functions require verification Verwendet in: Shared Data-Bus Isolation, Industrial Control Interface, Peripheral Interface Buffering
What is the SN74AC241N?
The SN74AC241N is an eight-channel, non-inverting CMOS buffer/line driver with two independently enabled 4-bit output banks and 3-state outputs. According to the Texas Instruments product page, it operates from 2 V to 6 V and is packaged in a 20-pin PDIP. It is intended for memory-address drivers, clock drivers, bus-oriented receivers, and transmitters where a driven output must be disconnected temporarily.
What are the key specifications of SN74AC241N that engineers should know?
The SN74AC241N provides eight non-inverting CMOS channels, two 4-bit output banks, 3-state operation, and a 2 V to 6 V supply range in a 20-pin PDIP package. Texas Instruments identifies the N-package operating range as -40 °C to 85 °C. The device is specifically intended to improve the performance and density of 3-state memory-address drivers, clock drivers, and bus-oriented interfaces, making the independent output-enable function central to its implementation.
What is the operating voltage of SN74AC241N?
The SN74AC241N operates from 2 V to 6 V according to the Texas Instruments SN74AC241 product page. This range supports both 3.3 V and 5 V CMOS logic systems. The family is also described as qualified for automotive applications to 6 V VCC operation, with a maximum input voltage of 6 V. Use the manufacturer datasheet for the exact input-current and static-power limits at each supported supply voltage.
What is the pinout of SN74AC241N?
The SN74AC241N uses a 20-pin PDIP package with eight data inputs, eight outputs, and output-enable controls for the two four-bit sections. Assign PCB connections from the pin-description table in the Texas Instruments SN74AC241 datasheet, including the exposed supply and ground pins. Do not infer enable polarity or data-pin numbering from a generic 74xx241 diagram without checking the manufacturer ordering table for the exact device.
Where can I download the SN74AC241N datasheet PDF?
The official Texas Instruments SN74AC241 datasheet PDF is available at https://www.ti.com/lit/ds/scas513g/scas513g.pdf. It covers the octal buffers and drivers with 3-state outputs and is the preferred document for pin descriptions, recommended operating conditions, electrical characteristics, timing, and package information. The family product page at https://www.ti.com/product/SN74AC241 provides ordering and quality information.
How does the SN74AC241N control its 3-state outputs?
The SN74AC241N divides its eight outputs into two 4-bit banks that can be placed in a high-impedance state independently. Texas Instruments describes the device as an octal buffer with 3-state outputs designed for bus-oriented signal paths. This arrangement lets a controller isolate one peripheral or memory bank while another enabled bank continues driving a shared bus, provided the design avoids simultaneous output contention.
Can SN74AC241N be used as a bidirectional transceiver?
No. The SN74AC241N is a unidirectional, non-inverting buffer rather than a bidirectional transceiver; its data paths carry signals in one direction, while the 3-state control disconnects the outputs from a shared bus. A bidirectional bus interface requires a device with configurable input and output drivers. Use the SN74AC241N where a source must drive a bus and receivers must be isolated when the driver is disabled.
Is SN74AC241N suitable for memory address and clock buffering?
The SN74AC241N is specifically designed for 3-state memory-address drivers, clock drivers, and bus-oriented receivers and transmitters. Its two independently controlled 4-bit sections can isolate selected address groups or clock/control loads when contention must be avoided. The exact usable clock rate depends on propagation delay, load capacitance, supply voltage, and output loading, so verify those values in the manufacturer datasheet for the target operating condition.
What is the difference between SN74AC241N and SN74AC241NE4?
The SN74AC241N and SN74AC241NE4 are both listed in 20-pin PDIP packages and provide the same SN74AC241 8-channel, 3-state buffer function. The retrieved comparison describes the NE4 device as functionally and terminally consistent enough to replace the N version without modification. Because package qualification and ordering codes can differ by revision or assembly, engineers should confirm the manufacturer ordering table and temperature requirements before approving a substitution.
Is SN74AC241 the same as SN74AC244?
No. The SN74AC241 is a non-inverting octal buffer with 3-state outputs, while the SN74AC244 family uses inverting buffers. The comparison data therefore identifies SN74AC244NE4 as a related device rather than a transparent functional equivalent. Replacing one with the other requires an inversion in the surrounding logic or careful reevaluation of every affected signal, so it should not be treated as a direct drop-in replacement.
What is the best drop-in replacement for SN74AC241N?
The SN74AC241NE4 is the best directly supported replacement candidate in the retrieved cross-reference information because it retains the 20-pin PDIP package and the same 8-channel, 3-state buffer function. No additional pin-compatible alternatives with independently verified parameters and the exact PDIP footprint were established. Before replacing the part, check the ordering table, temperature grade, lifecycle status, and required timing and load-current limits.
Can MC74ACT05NG replace SN74AC241N?
MC74ACT05NG should not be treated as a direct SN74AC241N drop-in replacement merely because both are 20-pin logic ICs. The retrieved comparison places MC74ACT05NG alongside SN74AC241N and SN74AC244NE4, but it does not establish identical pin functions, output-enable behavior, polarity, or operating characteristics. Use the manufacturer pinout and timing tables before considering any layout substitution; otherwise a board redesign may be required.
When should I choose SN74AC241N over SN74AC244NE4?
Choose SN74AC241N when the system requires non-inverting buffered signals, while choosing SN74AC244NE4 requires accounting for its inverting buffer behavior. Both are associated with the 20-pin PDIP SN74AC24x family, but substituting one for the other can reverse the logic sense of eight signal paths. SN74AC241N is the appropriate choice when downstream circuitry expects the same active logic level at the buffered output as at the input.
Where can I buy SN74AC241N and check its current price and lead time?
Use the Request a Quote form on this page to request the current price, stock position, minimum order quantity, and lead time for SN74AC241N. The Request a Quote workflow is also appropriate for production quantities where allocation can change between order dates. Engineers should specify the 20-pin PDIP package and the exact SN74AC241N manufacturer part number to avoid receiving a different package or logic variant.
How should SN74AC241N be placed on a PCB with long bus traces?
Place the SN74AC241N close enough to the driven bus section to minimize trace capacitance and ringing, while keeping the output-enable traces short and away from sensitive signals. The manufacturer specifies a 20-pin PDIP package, so inspect the board's through-hole footprint and maintain adequate clearance around neighboring components. For timing-critical buses, use the datasheet's recommended load and trace conditions to validate the propagation-delay budget.
What design mistakes can cause bus contention with SN74AC241N?
The most common errors are enabling a 4-bit output bank while another device drives the same bus nodes or connecting data inputs to uncontrolled signals. The SN74AC241N outputs become high impedance only when their associated output-enable function commands that state. Use decoded enables, account for power-up states, and ensure no two enabled outputs share a node. The family tolerates a maximum input voltage of 6 V, but it does not make intentional output contention safe.
Is SN74AC241N RoHS compliant and qualified for automotive applications?
The retrieved technical information states that SN74AC241 is qualified for automotive applications to 6 V VCC operation, but it does not provide a specific AEC-Q100 grade or an explicit RoHS declaration for the N package. Treat RoHS, REACH, lead-free, and halogen-free status as unknown until the manufacturer product page or declaration confirms them. For automotive production, verify the exact ordering code, qualification grade, and documentation with the manufacturer.

Technische Referenzdaten für SN74AC241N – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose SN74AC241N for a through-hole design that requires eight non-inverting, 3-state buffer channels with independent control of two 4-bit banks. Its 2 V to 6 V range suits both 3.3 V and 5 V CMOS systems, and the manufacturer specifically targets memory-address, clock-driver, and bus-oriented applications. SN74AC241NE4 is the preferred same-package alternative when its ordering code, qualification status, and temperature grade meet the production requirement. SN74AC244NE4 should be considered only for a deliberate inversion redesign because its buffered signals have the opposite polarity. MC74ACT05NG may be useful for a broader logic-interface comparison, but the retrieved material does not establish it as a pin-compatible replacement for the SN74AC241N enable and data functions. In every case, validate propagation delay, output-current capability, input-current behavior, and package-level regulatory requirements against the manufacturer datasheet before releasing the PCB.

Vergleich mit Alternativen

Parameter Dieses Produkt SN74AC241NE4
Package 20-pin PDIP (N) 20-pin PDIP (N)
Brand Texas Instruments Texas Instruments
Product Function Octal non-inverting 3-state buffer/line driver Octal non-inverting 3-state buffer/line driver
Number of Channels 8 8
Output Configuration Two independently enabled 4-bit banks Two independently enabled 4-bit banks
Supply Voltage Range 2 V to 6 V 2 V to 6 V
Logic Polarity Non-inverting Non-inverting
Technology CMOS CMOS
Mounting Type Through-hole Through-hole

Wichtigste Unterscheidungsmerkmale

  • Non-inverting bus-buffer behavior (vs. SN74AC244NE4)
  • Same-package replacement path (vs. SN74AC241NE4)
  • Independent control of two bus groups (vs. MC74ACT05NG)

Designhinweise

Define every output-enable state before routing the PCB. Two SN74AC241N output banks must never be enabled simultaneously when they connect to the same bus nodes, because both outputs would actively drive the network. Use decoded enables, account for reset and power-up states, and keep unused outputs in the high-impedance state. Also avoid substituting SN74AC244NE4 without redesigning the logic because its inverting polarity reverses the functional behavior of the buffered channels.

Use the manufacturer timing and load conditions when establishing a bus-frequency or clock-rate budget. The retrieved information confirms the 2 V to 6 V operating range and identifies clock-driver use, but it does not provide propagation delay or output-current figures. Obtain those limits from the SN74AC241 datasheet, include board capacitance and receiver loading in the evaluation, and ensure the selected trace topology does not create excessive ringing or overshoot at the output transition.

Place the supply bypass capacitor close to the device and provide a low-impedance ground return because output transitions can create fast current pulses. Keep output-enable traces short enough to avoid accidental glitches and separate them from sensitive signal paths. For the 20-pin PDIP footprint, verify hole size, row spacing, and pin numbering against the manufacturer's mechanical drawing; through-hole lead clearance and soldering access also need to be considered during board-layout approval.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The retrieved information states that the SN74AC241 family is qualified for automotive applications to 6 V VCC operation, but it does not specify an AEC-Q100 grade or explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for SN74AC241N.

Ähnliche Suchanfragen

SN74AC241N datasheet SN74AC241N pinout SN74AC241N datasheet pdf SN74AC241N equivalent SN74AC241N replacement SN74AC241N vs SN74AC241NE4 SN74AC241N vs SN74AC244NE4 SN74AC241N footprint SN74AC241N price SN74AC241N stock Texas Instruments SN74AC241N SN74AC241 2V 6V buffer SN74AC241 3-state output driver SN74AC241N memory address buffering SN74AC241N shared bus isolation

Verwandte Bauteile & Begriffe

Texas Instruments SN74AC241N SN74AC241 SN74AC241NE4 SN74AC244NE4 MC74ACT05NG 74AC CMOS logic octal buffer line driver 3-state output non-inverting buffer high-impedance state logic buffer bus-oriented receiver bus-oriented transmitter memory-address driver clock driver output-enable control propagation delay PDIP-20 through-hole package surface-mount package semiconductor 2 V to 6 V operating supply
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen