SN74AC241N - 8-Channel 3-State Buffer | Texas Instruments
部品番号: SN74AC241N ✓ 生産中SN74AC241N 概要
A logic buffer is a digital semiconductor that reproduces an input signal at an output while providing buffering between a source and the next circuit stage. The 74AC family belongs to the advanced CMOS logic hierarchy, combining low-power operation with balanced drive capability and relatively high input impedance. In the SN74AC241, the tri-state output function allows each group of four outputs to be placed in a high-impedance state, preventing a disabled driver from actively driving a shared bus.
The principal feature is independent output-enable control, allowing two 4-bit sections to be enabled or disabled separately. The non-inverting architecture preserves input logic polarity. Operation from 2 V to 6 V supports both 3.3 V and 5 V systems, while the maximum input voltage of 6 V provides tolerance for supply-transient conditions. The exact propagation-delay, output-current, input-current, and static-power values are not stated in the retrieved product information and must be confirmed in the manufacturer datasheet before timing, fanout, or signal-integrity calculations.
SN74AC241N is a bus-oriented octal buffer rather than a general-purpose open-collector transceiver. Unlike a bidirectional transceiver, its data paths are unidirectional, and unlike a conventional non-3-state buffer, each four-output bank can be disabled. This makes the device appropriate when a controller, memory interface, or peripheral must be isolated from a shared bus while preserving standard logic levels. The N suffix identifies the through-hole PDIP package; board layout, insertion, and rework requirements therefore differ from surface-mount alternatives.
Typical uses include address-line buffering between a memory controller and external memory, clock distribution into bus loads, isolation of peripherals from shared data buses, and buffering of control signals in modular industrial equipment. Because the device supports 3-state outputs, firmware or external logic can determine which bank drives a shared bus. Designers should still verify timing against the worst-case load and trace capacitance shown in the manufacturer datasheet rather than assuming performance from the family name alone.
Decoupling and signal-integrity practice remain important in high-speed systems. Place the supply bypass capacitor close to the device, provide a continuous return path for output-current transients, and keep enable traces away from sensitive analog paths. Do not enable a bank while two outputs contend on the same bus unless the downstream system explicitly supports bus contention. Confirm that the selected source and destination devices meet the AC family voltage, temperature, and timing limits before using the buffer as an interface between unrelated logic families.
This product page combines the manufacturer ordering information with practical bus-isolation guidance, verified package details, and a parameter-by-parameter replacement comparison. It also highlights the distinctions that matter during PCB design: the PDIP-20 footprint, independent 3-state enable control, unidirectional non-inverting operation, and the need to validate exact timing and drive-current limits against the selected system load.
ドロップイン代替品: SN74AC241N — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
SN74AC241NE4
✅ ドロップイン📋 参考代替品(カタログ未掲載)
SN74AC241N 最大定格&電気的特性
| Product Type | Octal non-inverting buffer/line driver |
| Logic Family | 74AC CMOS |
| Number of Channels | 8 channels |
| Number of Buffer Elements | 2 elements |
| Bits per Element | 4 bits per element |
| 出力タイプ | 3-state output |
| Logic Polarity | Non-inverting |
| Supply Voltage Range | 2 V to 6 V |
| Maximum Input Voltage | 6 V |
| Technology | CMOS |
| Package Type | 20-pin PDIP (N) |
| ピン数 | 20 pins |
| 実装タイプ | Through-hole |
| 動作温度範囲 | -40 °C to 85 °C |
| Automotive Qualification | Qualified for automotive applications to 6 V VCC operation |
| Output Enable Control | Independent control for two 4-bit output banks |
SN74AC241N 20-pin pdip (n) ピン配置ガイド
SN74AC241N (20-pin pdip (n) パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: SN74AC241N.
詳細は データシート をご参照ください。
主な用途
SN74AC241N の用途: 6 件s: Memory Address Buffering, Shared Data-Bus Isolation, Clock Distribution, Industrial Control Interface, Test and Measurement Equipment, Peripheral Interface Buffering.
Memory Address Buffering
The SN74AC241N fits between a memory controller and shared address lines because it provides eight non-inverting buffer channels divided into two independently controlled 4-bit banks. Each bank can be placed in a high-impedance state when it must not drive a bus, helping prevent contention during address multiplexing or memory-bank isolation. Its 2 V to 6 V operating range supports 3.3 V and 5 V systems, while the N package provides a conventional 20-pin PDIP footprint. Confirm propagation delay, output-current capability, and load capacitance in the manufacturer datasheet for the selected clock rate.
おすすめ
Shared Data-Bus Isolation
The SN74AC241N can isolate one group of four bus drivers while another group remains active, allowing peripheral data to share a common bus without every driver remaining connected. Its non-inverting, 3-state outputs preserve the source logic level and support selective participation in a bus-oriented system. The 2 V minimum supply permits operation in low-voltage CMOS logic environments, while the 6 V maximum supports 5 V rails. Use decoded output-enable logic and ensure all possible power-up, reset, and fault states prevent two devices from driving the same node simultaneously.
おすすめ
Clock Distribution
The SN74AC241N can buffer a clock into separate four-channel sections and disconnect a section when it is not needed. This makes it useful for modular backplanes, industrial controllers, and test equipment where clock loads must be isolated to reduce capacitive loading or avoid unwanted drive paths. Because the device is specified for clock-driver use, it provides a direct functional match for this application. The usable frequency must be checked against worst-case propagation delay, output loading, and supply voltage, and enable transitions should be synchronized with the system timing plan.
おすすめ
Industrial Control Interface
The SN74AC241N suits industrial control boards that separate local logic from external bus connectors or field-routing circuits. Two independent output banks provide selective isolation, and the through-hole 20-pin PDIP package is convenient for prototypes, repairable assemblies, and designs assembled through manual insertion. Its 2 V to 6 V supply range accommodates common industrial logic levels, while the -40 °C to 85 °C N-package range supports a broad operating environment. Layout review should include bus-length limits, surge requirements, grounding, and separation between sensitive control nodes and connector routing.
おすすめ
Test and Measurement Equipment
In test and measurement equipment, the SN74AC241N can buffer control, address, or fixture-control lines while keeping unused drivers electrically disconnected. The independent 3-state sections make it practical to route several instrument functions through a shared backplane without permanent contention. Its CMOS implementation and 2 V to 6 V operating range suit low-voltage digital control systems, while the PDIP package simplifies retrofit and repair. Validate timing over the complete operating-temperature range and verify that connected fixtures do not exceed the device's specified output-current and capacitive-load limits.
おすすめ
Peripheral Interface Buffering
The SN74AC241N is appropriate between a controller and a peripheral bus when the peripheral must be disconnected during reset, programming, or bus sharing. Eight non-inverting channels preserve data and control semantics, while two output-enable groups provide coarse isolation control. The device operates at 2 V to 6 V and is intended for bus-oriented receivers and transmitters, giving it a natural fit for CMOS peripheral interfaces. A complete design should include defined enable states, adequate supply bypassing, and timing checks for every bus transition to prevent contention or marginal data setup.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: SN74AC241N — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | SN74AC241NE4 |
|---|---|---|
| Package | 20-pin PDIP (N) | 20-pin PDIP (N) |
| Brand | Texas Instruments | Texas Instruments |
| Product Function | Octal non-inverting 3-state buffer/line driver | Octal non-inverting 3-state buffer/line driver |
| Number of Channels | 8 | 8 |
| Output Configuration | Two independently enabled 4-bit banks | Two independently enabled 4-bit banks |
| Supply Voltage Range | 2 V to 6 V | 2 V to 6 V |
| Logic Polarity | Non-inverting | Non-inverting |
| Technology | CMOS | CMOS |
| Mounting Type | Through-hole | Through-hole |
主な差別化要因
- Non-inverting bus-buffer behavior (vs SN74AC244NE4)
- Same-package replacement path (vs SN74AC241NE4)
- Independent control of two bus groups (vs MC74ACT05NG)
設計ノート
Define every output-enable state before routing the PCB. Two SN74AC241N output banks must never be enabled simultaneously when they connect to the same bus nodes, because both outputs would actively drive the network. Use decoded enables, account for reset and power-up states, and keep unused outputs in the high-impedance state. Also avoid substituting SN74AC244NE4 without redesigning the logic because its inverting polarity reverses the functional behavior of the buffered channels.
Use the manufacturer timing and load conditions when establishing a bus-frequency or clock-rate budget. The retrieved information confirms the 2 V to 6 V operating range and identifies clock-driver use, but it does not provide propagation delay or output-current figures. Obtain those limits from the SN74AC241 datasheet, include board capacitance and receiver loading in the evaluation, and ensure the selected trace topology does not create excessive ringing or overshoot at the output transition.
Place the supply bypass capacitor close to the device and provide a low-impedance ground return because output transitions can create fast current pulses. Keep output-enable traces short enough to avoid accidental glitches and separate them from sensitive signal paths. For the 20-pin PDIP footprint, verify hole size, row spacing, and pin numbering against the manufacturer's mechanical drawing; through-hole lead clearance and soldering access also need to be considered during board-layout approval.
コンプライアンス情報
The retrieved information states that the SN74AC241 family is qualified for automotive applications to 6 V VCC operation, but it does not specify an AEC-Q100 grade or explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for SN74AC241N.