SN74HC368N - 6-Channel Inverting Tri-State Buffer | Texas Instruments
Teilenummer: SN74HC368N ✓ AktivSN74HC368N Übersicht
A tri-state buffer is a digital logic device that can actively drive a logic 0 or logic 1 while also presenting a high-impedance state when disabled. The SN74HC368 belongs to the HC CMOS logic family and is designed for memory-address drivers, clock drivers, and bus-oriented receivers and transmitters. Its inverting channels support clock distribution and control-signal routing where signal polarity reversal is intentional or can be accommodated by downstream circuitry.
The device provides six usable output channels, a 2 V to 6 V supply range, and independent control of the grouped four-line and two-line output sections. Its three-state outputs allow multiple drivers to share a bus when only one driver is enabled at a time. The SN74HC368N ordering code specifies a temperature range of -40 °C to 85 °C and a PDIP package with 16 pins.
Unlike a standard push-pull buffer that continuously sources or sinks output current, the SN74HC368 can disconnect each enabled output group from the bus. Active-low output-enable inputs provide straightforward bus arbitration and prevent contention when several buffers share address, clock, or control lines. The dual four-line and two-line organization lets a designer disable related channels together while retaining independent control over the smaller group.
Typical uses include three-state memory-address buffering, clock distribution, bus-oriented signal conditioning, and control interfaces in industrial control, instrumentation, embedded, and communications equipment. The inverting action is particularly useful when clock polarity must be reversed between source and destination. When several devices drive one bus, their enable inputs must be controlled so that no two output groups are active simultaneously.
For reliable implementation, use the manufacturer pin-description table when assigning PCB nets and observe the absolute maximum ratings and recommended operating conditions. Decoupling capacitors should be placed close to the supply pins, while enable traces should be kept short and away from high-current switching nodes. Inputs must remain within the specified logic levels and must not be left floating.
This page consolidates the device architecture, package details, sourcing guidance, replacement considerations, comparison parameters, and practical implementation notes needed to evaluate the SN74HC368N for a new or existing PCB design.
Drop-in-Alternativen für SN74HC368N – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
74HC368N,652
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
SN74HC368N Grenzwerte & elektrische Eigenschaften
| Number of Channels | 6 channels |
| Logic Type | Inverting |
| Ausgangskonfiguration | 3-state output |
| Supply Voltage Range | 2 V to 6 V |
| Speicherorganisation | Dual 4-line and 2-line buffer/driver sections |
| Output Enable | Active-low |
| Output State | Inverted data or high-impedance when disabled |
| Gehäuse | 16-pin PDIP |
| Betriebstemperaturbereich | -40 °C to 85 °C |
| Montageart | Through-hole |
| Primary Application | Memory address, clock, and bus drivers |
| Operating Free-Air Temperature | -40 °C to 85 °C |
SN74HC368N 16-pin pdip Pinbelegungsleitfaden
Pinbelegung für SN74HC368N (16-pin pdip-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für SN74HC368N.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
SN74HC368N ist geeignet für 6 Anwendungs: Memory Address Buffering, Clock Distribution, Bus-Oriented Signal Conditioning, Industrial Control Interfaces, Test and Measurement Systems, Embedded Control Logic.
Memory Address Buffering
The SN74HC368N is well suited to three-state memory-address buffering because it provides six inverting channels in two four-line groups and one two-line group. Each group can be disabled independently with its active-low output enable, allowing selected address lines to drive a shared bus while remaining groups enter a high-impedance state. The 2 V to 6 V operating range supports multiple HC-series logic systems. Designers should ensure that only one driver group is enabled at a time, control the enables with valid CMOS levels, and use the manufacturer's pin table to route the four-line and two-line sections correctly.
Empfohlen
Clock Distribution
The SN74HC368N can distribute clock signals through six inverting channels while offering grouped three-state control for shared clock buses. Its two four-line sections and one two-line section permit the system to enable only the destinations that require the clock, while disabled outputs remain electrically disconnected. This is useful when several clock domains must share conductors without continuous output contention. Confirm that inversion is acceptable at the destination and that enable transitions do not create clock-edge hazards.
Empfohlen
Bus-Oriented Signal Conditioning
The SN74HC368N can condition inverting control, address, or communication-related signals that must connect to a tri-state bus. When the active-low output enable is asserted, the selected channel group drives inverted data; when deasserted, the same outputs provide high impedance and release the bus. This architecture supports bus arbitration, test isolation, and modular routing. Use pull devices only where required by the wider system, and verify timing margins because the inverting function changes clock and data polarity.
Empfohlen
Industrial Control Interfaces
The SN74HC368N can support grouped control-signal routing in industrial equipment where multiple buffered outputs must connect to a common backplane or interface bus. Its active-low enables help isolate subsystems during startup, diagnostics, or maintenance, while the high-impedance output state prevents unused channels from loading the bus. The 2 V to 6 V supply range aligns with HC CMOS logic levels, but system designers must verify noise margins, propagation timing, temperature behavior, and output drive at the actual supply voltage and loading.
Empfohlen
Test and Measurement Systems
The SN74HC368N is applicable in test and measurement equipment when instrument resources must drive shared lines selectively. Six inverting, three-state channels can route clock, trigger, or control signals while disabled groups remain isolated from the common node. Grouped enables simplify control of four-line and two-line sections without requiring a separate buffer for every signal. Before using the device in a precision instrument, verify propagation delay, output rise and fall behavior, capacitive-load limitations, and whether inverted timing polarity requires compensation elsewhere in the signal path.
Empfohlen
Embedded Control Logic
The SN74HC368N can serve as an interface stage between embedded control logic and grouped external bus signals. Its inverting channels can generate inverted clock or control waveforms, and its active-low output enables let firmware or hardware control bus participation. Because the device operates from 2 V to 6 V, it fits HC-series systems where the selected voltage still satisfies the required noise margin and timing. Firmware must maintain exclusive bus ownership, and hardware should include defined enable states so startup or reset does not leave multiple drivers active.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für SN74HC368N – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | 74HC368N,652 |
|---|---|---|
| Package | 16-pin PDIP | 16-pin PDIP |
| Brand | Texas Instruments | NXP |
| Number of Channels | 6 channels | 6 channels |
| Logic Type | Inverting | Inverting |
| Output Configuration | 3-state output | 3-state output |
| Output Enable | Active-low | Active-low |
| Channel Organization | Dual 4-line and 2-line sections | Dual 4-line and 2-line sections |
| Primary Application | Address, clock, and bus drivers | Address, clock, and bus drivers |
Wichtigste Unterscheidungsmerkmale
- Provides six individually routed but grouped tri-state outputs (vs. 74HC368N,652)
- Supports the standard HC-series supply range (vs. 74HC368N,652)
- Combines inversion with selectable bus participation (vs. 74HC368N,652)
Designhinweise
Ensure that no two connected SN74HC368N output groups drive the same bus simultaneously. The active-low output-enable inputs must have defined states during reset, startup, and shutdown, and they should never be left floating. Use the manufacturer's functional diagram to determine which pins control the four-line and two-line groups.
Place the supply-decoupling capacitor close to the device's supply and ground connections, and keep enable and data traces short enough to avoid additional propagation delay or coupling. For through-hole construction, provide adequate copper area and clean ground returns. If outputs drive longer PCB traces or cables, verify rise time, overshoot, and capacitive-load limits in the manufacturer electrical-characteristics tables.
Account for the inverting action at every destination because a clock, reset, or control edge polarity may reverse between the buffer input and output. Also evaluate the timing difference between propagation through data and enable paths. Disable outputs before changing bus ownership, and use a defined non-conflicting state in arbitration logic to prevent short current pulses.
Compliance-Informationen
The verified product excerpts do not state the exact-part RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. The SN74HC368N is a commercial HC CMOS logic device rather than an automotive-qualified variant.