SN74HC393N - Dual 4-Bit Binary Counter | Texas Instruments
Teilenummer: SN74HC393N ✓ AktivSN74HC393N Übersicht
A binary counter is a digital sequential-circuit component that stores an n-bit number and advances that number after each active clock transition. In the SN74HC393N, each 4-bit section can therefore represent 16 count states, while the two sections operate independently. Within the broader logic hierarchy, this product is a counter IC, a type of synchronous digital logic IC used to divide frequency, count repeated events, or establish predictable timing relationships in a circuit.
The SN74HC393N provides two independent 4-bit counting channels in one package, reducing board area compared with two separate single-counter devices. Its eight internal flip-flops and gating provide parallel outputs for every counting stage, allowing multiple submultiples of the input clock frequency to be observed. The negative-edge clocking behavior is important because each counter changes state on the falling transition rather than the rising transition of its clock waveform.
The two counting sections each include an individual clock and clear function, so they can be started and reset independently when separate event streams are required. This makes the device more flexible than a simple fixed-divider arrangement. Output states can also be decoded for modulus generation, while the clear inputs allow a count sequence to be returned to its starting state after a defined number of cycles. The manufacturer documentation identifies the SN74HC393 family as comprising two individual 4-bit binary counters.
Typical uses include divide-by-16 clock generation, digital time-base and timer modules, pulse and event counting, address sequencing, frequency division in communication equipment, and general control logic in industrial or embedded systems. Two independent sections allow one counter to handle a recurring timing reference while the other counts external events. Parallel outputs can be cascaded externally when a count range wider than four bits is required.
PCB design should preserve the counter's clock and clear signal paths, particularly when the device participates in a timing chain. Keep clock traces short, maintain a common ground reference, and route output signals away from high-current switching nodes. Because the part is supplied in a 14-pin PDIP package, lead spacing and drilled through-hole dimensions must match the PCB footprint. Confirm the pin assignments in the Texas Instruments datasheet before final routing.
This product page organizes the verified device identity, package information, operating function, drop-in alternatives, and design guidance into a compact engineering reference. It also highlights the difference between functional timing applications and a physical PCB replacement, helping engineers select a replacement only when both the logic behavior and 14-pin footprint are compatible.
Drop-in-Alternativen für SN74HC393N – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
SN74HC393NE4
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
74HC393N,652
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
MM74HC393N
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
HD74HC393P
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
SN74HC393N Grenzwerte & elektrische Eigenschaften
| Counter Type | Binary counter |
| Number of Counter Elements | 2 elements |
| Bits per Counter | 4 bits |
| Clock Edge | Negative edge |
| Total Flip-Flops | 8 flip-flops |
| Ausgangskonfiguration | 4 parallel outputs per counter |
| Independent Counter Sections | 2 |
| Clock Inputs | 1 per counter |
| Clear Inputs | 1 per counter |
| Gehäuse | 14-PDIP |
| Pin-Anzahl | 14 pins |
| Montageart | Through-hole |
SN74HC393N Pin-Konfiguration
| Pin 1 | CLR1 — Asynchronous clear input for counter 1 |
| Pin 2 | Q1A — Parallel output A of counter 1 |
| Pin 3 | Q1B — Parallel output B of counter 1 |
| Pin 4 | Q1C — Parallel output C of counter 1 |
| Pin 5 | Q1D — Parallel output D of counter 1 |
| Pin 6 | CLK1 — Negative-edge clock input for counter 1 |
| Pin 7 | GND — Ground reference |
| Pin 8 | Q2A — Parallel output A of counter 2 |
| Pin 9 | Q2B — Parallel output B of counter 2 |
| Pin 10 | Q2C — Parallel output C of counter 2 |
| Pin 11 | Q2D — Parallel output D of counter 2 |
| Pin 12 | CLK2 — Negative-edge clock input for counter 2 |
| Pin 13 | CLR2 — Asynchronous clear input for counter 2 |
| Pin 14 | VCC — Positive supply voltage |
Typische Anwendungen
SN74HC393N ist geeignet für 6 Anwendungs: Binary Frequency Divider, Digital Event Counter, Timer and Time-Base Logic, Address and State Sequencing, Communication Timing and Pulse Counting, Test and Measurement Equipment.
Binary Frequency Divider
The SN74HC393N suits digital frequency-divider and clock-generation circuits because each section counts on the negative edge and exposes four parallel outputs from its 4-bit counting stages. A 16-count sequence can be divided directly from one section, while the second section can provide another independent division ratio or event count. This arrangement reduces component count compared with using two separate counter packages. Before finalizing the timing chain, verify the maximum operating frequency, propagation delay, and output transition characteristics in the Texas Instruments datasheet for the selected supply voltage.
Empfohlen
Digital Event Counter
Each independent counter section in the SN74HC393N can count recurring external events and retain the result in a 4-bit binary state. The package is useful in laboratory, industrial, and control systems where one channel counts cycles while the other tracks a separate event stream. The parallel outputs allow individual count states to be observed without repeatedly decoding the full binary value. Clear inputs support deterministic reset after a target count is reached, although the external input conditioning and maximum input frequency must be validated against the manufacturer's electrical characteristics.
Empfohlen
Timer and Time-Base Logic
The two independent 4-bit sections of the SN74HC393N can support timer intervals, elapsed-event timing, and system time-base generation. One negative-edge counter channel may establish a periodic interval while the other performs a secondary division or event-counting function. Its parallel count outputs provide several usable intermediate timing states, helping reduce the number of external decoding gates. For battery-powered or precision timing equipment, check the supported supply range, quiescent behavior, and timing tolerance in the manufacturer documentation before choosing the device.
Empfohlen
Address and State Sequencing
The SN74HC393N can implement binary state sequencing in control logic because each 4-bit counter advances on a falling clock edge and exposes all four count states as parallel outputs. A second counter can maintain another state sequence, allowing two coordinated sequences to run from related or separate clocks. This is useful in test fixtures, programmable controllers, and sequencing logic where compact counter state is required. Account for setup and hold timing at the clock and clear inputs, and confirm that the counter polarity matches the state-machine requirements.
Empfohlen
Communication Timing and Pulse Counting
The SN74HC393N can divide repetitive communication or synchronization pulses and count externally received events in a compact 14-pin package. Two independent sections allow a recovered timing signal to be divided while a separate channel counts message or frame events. Its negative-edge operation must be considered when the surrounding circuit already uses other logic on the falling transition. Check propagation delay and output timing margin against the system clock budget, and use the datasheet pin table to preserve the correct clear-input polarity.
Empfohlen
Test and Measurement Equipment
The SN74HC393N is useful as a compact binary counter in test and measurement equipment that must count test cycles, derive division ratios, or generate repeating timing intervals. Two independent channels provide flexibility for coordinating an instrument's timing with an event count. The parallel outputs can be routed to display, capture, or control circuitry without adding a separate multiplexer. Designers should compare the device's operating conditions and timing limits with the instrument's voltage, temperature, and clock requirements, and ensure unused inputs are connected according to the datasheet.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für SN74HC393N – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | SN74HC393NE4 | 74HC393N,652 | MM74HC393N | HD74HC393P |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | NXP Semiconductors | onsemi | Renesas Electronics |
| Package | 14-PDIP | 14-PDIP | 14-DIP | 14-PDIP | 14-PDIP |
| Counter Type | Binary counter | Binary counter | Binary counter | Binary counter | Binary counter |
| Counter Elements | 2 elements | 2 elements | 2 elements | 2 elements | 2 elements |
| Counter Width | 4 bits | 4 bits | 4 bits | 4 bits | 4 bits |
| Clock Edge | Negative edge | Negative edge | Negative edge | Negative edge | Negative edge |
| Internal Flip-Flops | 8 flip-flops | 8 flip-flops | 8 flip-flops | 8 flip-flops | 8 flip-flops |
Wichtigste Unterscheidungsmerkmale
- Two independent counters in one package (vs. 74HC393N,652)
- Parallel access to every counter stage (vs. MM74HC393N)
- Negative-edge counting supports deterministic clocking (vs. HD74HC393P)
- Single-package channel consolidation (vs. CD74HC4520E)
Designhinweise
Treat each clock input as a timing-sensitive node. Route it directly to the intended counter pin, keep the path short, and avoid sharing a long trace with unrelated outputs where switching activity could create crosstalk. Because the counters advance on the falling edge, check source timing, propagation delay, and setup or hold requirements against the system clock budget using the manufacturer timing characteristics.
Confirm that the PCB footprint matches a 14-pin PDIP rather than a 14-pin surface-mount package. Check row spacing, lead length, drill diameter, and pin-1 orientation before layout release. Keep ground and supply connections short, use a common ground reference, and decouple the supply close to the device in accordance with the manufacturer layout guidance. Verify every net against the datasheet pin-description table.
Do not substitute a 74HC390-family counter merely because both devices use a 14-pin package; decade-counter outputs, count modulus, and pin assignments differ. Likewise, verify clear-input polarity and clock-edge behavior for every proposed replacement. A physical package match is necessary but insufficient: the logical function, supply limits, timing, temperature range, and qualification requirements must also satisfy the design.
When the two counters operate from one clock, route the source so both channels receive equivalent propagation delay. If the counters use separate clocks, maintain independent return paths and avoid long ground loops. The four parallel outputs of each channel can be routed as a binary bus or decoded individually; fanout and trace loading should be checked against the output-current and timing specifications before adding excessive loading.
Compliance-Informationen
The verified product information does not state the requested compliance attributes. AEC-Q100 is recorded as not applicable because this is a general-purpose logic counter rather than an automotive-qualified device.