SN74HC684N - 8-Bit Magnitude Comparator | Texas Instruments
Teilenummer: SN74HC684N ✓ AktivSN74HC684N Übersicht
A magnitude comparator is a digital logic IC that determines the relative order of two binary numbers. The SN74HC684N compares eight A-input bits with eight B-input bits, making it a parallel comparator within the logic IC, digital comparator, and arithmetic/comparison IC hierarchy. Its identity output indicates equality, while its greater-than output indicates that the A bus is numerically greater than the B bus. Active-low outputs allow convenient wired logic and can be directly used as active-low status signals.
The principal features of the SN74HC684N include 8-bit parallel comparison, separate equality and greater-than outputs, active-low output polarity, 20-pin PDIP construction, and a listed commercial operating-temperature range of -40°C to +85°C. The DIP package supports conventional through-hole assembly and prototyping, while the 74HC logic family provides CMOS-compatible operation with low static power characteristics. Exact supply-voltage, output-current, and timing limits must be taken from the manufacturer datasheet.
Internally, the comparator evaluates the relative magnitude of the two 8-bit input buses and generates the equality and greater-than decisions through combinational logic. Because it is a purely combinational device, its output responds to the current input-bus state after the specified propagation delay. Unlike an arithmetic processor, it does not calculate a difference or retain a previous comparison, making it useful as a dedicated decision element in control, sorting, addressing, and test circuitry.
Typical uses include sorting data words, detecting when one bus is equal to or greater than another, generating threshold decisions in industrial control, and implementing comparisons in digital test equipment. It can also support address-range decoding and sequencing logic. System designers should ensure that input transitions do not create invalid intermediate states when multiple bits change simultaneously and that downstream logic interprets the active-low outputs correctly.
For new designs, place decoupling capacitors close to the supply and ground pins, route high-current and switching signals away from comparator inputs, and use clean input traces to minimize false decision transitions. Because the PDIP footprint is not as compact as modern surface-mount packages, SN74HC684N is best suited to legacy-compatible, through-hole, and prototype assemblies rather than space-constrained new products.
This page consolidates the SN74HC684N function, package information, temperature range, complete 20-pin assignment, sourcing guidance, and practical logic-design considerations. It also explains the limits of direct replacement decisions so engineers can verify pinout, voltage compatibility, timing, and lifecycle requirements before approving any substitute.
Drop-in-Alternativen für SN74HC684N – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.
Alternativen anfordernSN74HC684N Grenzwerte & elektrische Eigenschaften
| Comparator Type | 8-bit identity/magnitude comparator |
| Number of Input Bits | 8 bit |
| A Input Width | 8 bit |
| B Input Width | 8 bit |
| Equality Output | A=B, active-low |
| Greater-Than Output | A>B, active-low |
| Logic Family | 74HC CMOS |
| Package Type | 20-pin PDIP |
| Anzahl der Pins | 20 pin |
| Montageart | Through-hole |
| Betriebstemperaturbereich | -40°C to +85°C |
| Datasheet Revision | Rev. B |
SN74HC684N Pin-Konfiguration
| Pin 1 | B0 — B input bit 0 |
| Pin 2 | B1 — B input bit 1 |
| Pin 3 | B2 — B input bit 2 |
| Pin 4 | B3 — B input bit 3 |
| Pin 5 | B4 — B input bit 4 |
| Pin 6 | B5 — B input bit 5 |
| Pin 7 | B6 — B input bit 6 |
| Pin 8 | B7 — B input bit 7 |
| Pin 9 | A7 — A input bit 7 |
| Pin 10 | A6 — A input bit 6 |
| Pin 11 | A5 — A input bit 5 |
| Pin 12 | A4 — A input bit 4 |
| Pin 13 | A3 — A input bit 3 |
| Pin 14 | A2 — A input bit 2 |
| Pin 15 | A1 — A input bit 1 |
| Pin 16 | A0 — A input bit 0 |
| Pin 17 | A>B — Active-low greater-than output |
| Pin 18 | A=B — Active-low equality output |
| Pin 19 | GND — Ground reference |
| Pin 20 | VCC — Positive power supply |
Typische Anwendungen
SN74HC684N ist geeignet für 6 Anwendungs: Industrial Control Decision Logic, Data Sorting and Ranking, Address Range Detection, Digital Test and Measurement, Sequence and Threshold Control, Legacy Equipment Maintenance.
Industrial Control Decision Logic
The SN74HC684N fits industrial control systems that must compare an 8-bit process or command value with a stored reference without sending every decision to a controller. Two 8-bit input buses feed the comparator, while the active-low A=B and A>B outputs provide hardware indications of equality and ordering. This allows a control system to detect setpoint coincidence or a threshold crossing before generating actuator commands. The 20-pin PDIP package is convenient for legacy control boards and through-hole prototypes. Timing must be checked against the SN74HC684 datasheet, and supply bypassing should be placed close to the device to limit logic noise.
Empfohlen
Data Sorting and Ranking
The SN74HC684N can support hardware sorting or ranking of two 8-bit values in a digital data path. When a new value arrives on the A bus and a stored value is presented on the B bus, the active-low greater-than and equality outputs identify whether the incoming word should advance, replace, or compare equal to the current item. This reduces comparison latency in a controller or programmable-logic design. The 74HC CMOS implementation operates as combinational logic, so system timing must include its specified propagation delay and account for simultaneous changes across multiple input bits.
Empfohlen
Address Range Detection
In address-range detection, the SN74HC684N compares an 8-bit address or index against a reference bus and asserts its active-low equality or greater-than output when the corresponding condition is met. These outputs can participate in chip-select, boundary, or sequencing logic without requiring a processor to perform a subtraction. The comparator is particularly useful for preserving legacy 8-bit bus architecture because it accepts parallel inputs and provides dedicated comparison results. Designers should verify output timing against the slowest receiving logic and ensure that address signals remain within the electrical limits stated in the manufacturer datasheet.
Empfohlen
Digital Test and Measurement
The SN74HC684N is useful in digital test equipment for checking whether two 8-bit measurement codes or test vectors are equal or ordered. A reference value can drive the B bus while the unit under test drives the A bus, and the two active-low outputs provide immediate comparison status. This hardware check can complement a processor-based test routine or operate independently as a diagnostic circuit. The PDIP package supports bench and laboratory through-hole construction. Keep test buses away from noisy analog routing and follow the manufacturer’s input, output, and decoupling guidance to prevent false comparisons.
Empfohlen
Sequence and Threshold Control
The SN74HC684N can implement an 8-bit threshold decision by comparing a live counter, register value, or encoded setting against a fixed bus. The active-low A>B output becomes a transition indication when the live value exceeds the threshold, while A=B identifies an exact programmed point. This arrangement is helpful for staged sequence control, event counting, and configurable setpoint logic. Because the outputs are active-low, downstream circuitry must use the correct inversion convention. The design should also account for bus settling and propagation delay to avoid detecting a transient result during multi-bit transitions.
Empfohlen
Legacy Equipment Maintenance
The SN74HC684N is well suited to repairing or extending older 8-bit digital equipment that uses through-hole 74HC logic and requires a dedicated magnitude comparator. Its 20-pin PDIP construction allows it to be assembled on replacement or prototype boards without changing to a surface-mount footprint. Maintenance engineers should confirm the existing board’s active-low output wiring, supply voltage, and timing requirements before installation. A socketed assembly can simplify future replacement, while bypassing capacitors near the supply and ground pins can help maintain stable operation in older cabinets with noisier power distribution.
Empfohlen
Technische Referenzdaten für SN74HC684N – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Do not select it merely because another comparator is also described as an 8-bit magnitude comparator. Confirm the candidate’s input and output pin assignments, output polarity, supply range, input and output current limits, propagation delay, temperature grade, and package. A surface-mount option may be preferable for a new compact design, while an active-high-output device may simplify a particular downstream circuit but require logic inversion. Before using any substitute, validate it against the SN54HC684/SN74HC684 datasheet and confirm the exact manufacturer ordering variant and lifecycle status.
Vergleich mit Alternativen
| Parameter | Dieses Produkt |
|---|---|
| Package | 20-pin PDIP |
| Brand | Texas Instruments |
| Comparator Type | 8-bit identity/magnitude comparator |
| Input Width | 8 bit |
| Equality Output | Active-low A=B |
| Greater-Than Output | Active-low A>B |
| Operating Temperature | -40°C to +85°C |
| Mounting Type | Through-hole |
| Logic Family | 74HC CMOS |
Wichtigste Unterscheidungsmerkmale
- Dedicated 8-bit identity and magnitude comparison (vs. Generic 8-bit magnitude comparator)
- Legacy-compatible 20-pin PDIP interface (vs. Surface-mount 8-bit comparator)
- Two comparison results in one device (vs. Separate equality-only logic)
Designhinweise
Treat the A and B buses as synchronous signals and account for comparator propagation delay before sampling either output. If several bits change at once, use registered bus sources or equalize their update timing so the comparator does not briefly evaluate an unintended intermediate value. Use short traces, a continuous return path, and positions away from switching nodes to reduce false decisions and ringing.
Place the supply-bypass capacitor immediately between the VCC and GND pins, with the shortest practical ground connection. Keep the through-hole footprint free of unintended copper or solder bridges around adjacent logic pins. Because output polarity is active-low, label A=B and A>B accordingly and avoid connecting downstream circuits that assume true or active-high outputs without adding inversion.
Do not treat a generic 8-bit comparator as a drop-in replacement without checking every input and output assignment. Also verify that the substitute uses the same 20-pin PDIP footprint, supply range, output polarity, and propagation-delay characteristics. The SN74HC684N compares unsigned binary values; signed arithmetic requires additional sign handling, and changing package technology can require PCB redesign.
Compliance-Informationen
The exact SN74HC684N ordering variant should be checked in the manufacturer ordering and environmental information. AEC-Q100 is not applicable because this is a commercial logic IC rather than an automotive-qualified device.