SP3232EHEP-L - 3.3V 460kbps RS-232 Transceiver | MaxLinear
Teilenummer: SP3232EHEP-L ✓ AktivSP3232EHEP-L Übersicht
An RS-232 transceiver is an interface IC that combines differential line drivers and receivers with the voltage conversion required to communicate with RS-232 equipment. In the broader semiconductor hierarchy, it belongs to interface ICs and serves as the physical communication layer between a low-voltage digital controller and an RS-232 port. The SP3232EH family targets portable and hand-held applications such as notebook and laptop computers.
The principal operating characteristics are a 3.3 V supply, two driver channels, two receiver channels, and throughput up to 460 kbps. These four features make the SP3232EHEP-L appropriate for point-to-point serial links, configuration ports, service interfaces, and embedded equipment that must exchange RS-232 signals without employing a larger multi-channel transceiver.
MaxLinear describes the SP3232EH as a 2-driver/2-receiver RS-232 solution using a high-efficiency charge-pump power supply. According to the manufacturer data sheet, the charge-pump arrangement requires only 0.1 µF capacitors for 3.3 V operation. This architecture supports a compact external component set while maintaining the elevated and inverted voltage levels required by RS-232 driver outputs.
Typical uses include portable data-acquisition equipment, industrial serial adapters, test fixtures, and controller boards with a legacy RS-232 service port. The 460 kbps rate supports substantially faster communication than conventional low-speed serial links while retaining the simple point-to-point interface of RS-232. System designers should still account for cable length, ground reference, transient protection, and protocol timing.
When laying out the circuit, place the charge-pump capacitors and receiver bypass capacitors close to their associated device pins. Keep the RS-232 driver and receiver routes away from sensitive analog or high-speed digital paths, and provide the protection appropriate to the exposed connector environment. Follow the manufacturer data sheet for capacitor selection, pin assignments, and maximum operating conditions.
This page consolidates the manufacturer specifications, package information, sourcing guidance, comparison points, and practical integration considerations for the SP3232EHEP-L. It is intended to help engineers identify a genuine same-footprint alternative, evaluate the 3.3 V and 460 kbps operating envelope, and plan a robust RS-232 interface before releasing the circuit to production.
Drop-in-Alternativen für SP3232EHEP-L – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit SP3232EHEP-L (gleiche Bauform und Footprint) – abweichend in Package.
SP3232EHEP
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
SP3232EHEY-L/TR
✅ Drop-In✓ Auf Lager
$0.2224 / Stück
Datenblatt ansehen →SP3232EHEP-L Technische Daten
| Product Type | RS-232 transceiver |
| Versorgungsspannung | 3.3 V |
| Maximum Data Rate | 460 kbps |
| Driver Channels | 2 |
| Receiver Channels | 2 |
| Interface Standard | RS-232 |
| Charge-Pump Capacitor Requirement | 0.1 µF in 3.3 V operation |
| Power-Supply Architecture | High-efficiency charge-pump power supply |
| Gehäuse | 16-pin TSSOP |
| Montageart | Surface mount |
SP3232EHEP-L 16-pin tssop Pinbelegungsleitfaden
Pinbelegung für SP3232EHEP-L (16-pin tssop-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für SP3232EHEP-L.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
SP3232EHEP-L ist geeignet für 6 Anwendungs: Portable Serial Adapters, Industrial Data-Acquisition Equipment, Test and Measurement Fixtures, Embedded Controller Service Ports, Point-to-Point Communication Links, Battery-Powered Serial Equipment.
Portable Serial Adapters
The SP3232EHEP-L suits portable equipment that needs to expose an RS-232 service or configuration port without allocating space for a larger transceiver. Its two drivers and two receivers support bidirectional point-to-point communication, while the 460 kbps rate is substantially faster than legacy low-speed serial operation. The 3.3 V supply and 0.1 µF charge-pump capacitors identified by the manufacturer help reduce the surrounding component count. When implementing the adapter, connect the logic-side signals to the host controller through the data-sheet pin table and protect the connector-side lines according to the expected cable and ESD environment.
Empfohlen
Industrial Data-Acquisition Equipment
The SP3232EHEP-L can provide the RS-232 link between an acquisition controller and a service terminal or legacy instrument. Two receiver channels allow the controller to monitor more than one incoming RS-232 signal, while two drivers support outbound command or status traffic. Operation at up to 460 kbps permits short, well-controlled transfers without requiring a higher-speed differential interface. The design should include suitable transient protection at the external connector and should verify that the attached cable length, grounding method, and protocol timing remain reliable at the selected baud rate.
Empfohlen
Test and Measurement Fixtures
The SP3232EHEP-L is useful in compact test fixtures where a computer or embedded controller must communicate with older RS-232 test equipment. Its 460 kbps capability supports efficient command transfer, and the two-driver/two-receiver configuration provides the fundamental channels needed for bidirectional control. Because the transceiver is designed for 3.3 V systems, the fixture controller can use a low-voltage logic domain without adding a separate level-shifting stage. Keep fixture wiring short, maintain a common ground between connected equipment, and place any protection network at the exposed connector rather than allowing external transients to reach the transceiver pins directly.
Empfohlen
Embedded Controller Service Ports
The SP3232EHEP-L provides a compact service interface for embedded controllers that retain an RS-232 connector for configuration, diagnostics, or firmware loading. The 16-pin TSSOP package preserves PCB area, and the 3.3 V operating point aligns with many controller, sensor, and communication subsystems. Its two drivers and two receivers allow command output and response input over the same physical interface. During schematic capture, distinguish the TTL/CMOS-side pins from the RS-232-side pins according to the manufacturer pin-description table, and follow the recommended charge-pump capacitor connections to maintain reliable signal generation.
Empfohlen
Point-to-Point Communication Links
The SP3232EHEP-L supports compact point-to-point links where two systems exchange RS-232 commands and responses. A maximum rate of 460 kbps provides adequate throughput for configuration traffic, short data packets, and status polling, while the integrated charge pump simplifies the external voltage-generation network. The device is particularly useful where only one RS-232 port is required and a multi-channel transceiver would add unused pins. Validate the link with realistic startup behavior, cable capacitance, and connector geometry because the maximum signaling rate does not remove the physical limitations of long or poorly terminated RS-232 cables.
Empfohlen
Battery-Powered Serial Equipment
The SP3232EHEP-L is suitable for battery-powered instruments and field equipment that need an RS-232 connection at a 3.3 V supply level. The low-voltage charge-pump implementation described by the manufacturer uses 0.1 µF capacitors in 3.3 V operation, supporting a compact and energy-conscious interface arrangement. The device's two transmitter and two receiver channels can serve both control commands and returned status without adding another serial transceiver. For a portable design, confirm the exact quiescent and loaded supply-current limits from the manufacturer data sheet, then include an appropriate connector-state strategy so unused RS-232 lines do not increase system energy use unnecessarily.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für SP3232EHEP-L – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | SP3232EHEP | SP3232EHEY-L |
|---|---|---|---|
| Brand | MaxLinear | MaxLinear | MaxLinear |
| Package | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP |
| Product Type | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
| Driver Channels | 2 | 2 | 2 |
| Receiver Channels | 2 | 2 | 2 |
| Target Application | Portable and hand-held RS-232 equipment | Portable and hand-held RS-232 equipment | RS-232 interface equipment |
Wichtigste Unterscheidungsmerkmale
- Provides two-driver and two-receiver integration in a 16-pin TSSOP (vs. SP3232EHEY-L)
- Uses a low-voltage charge-pump implementation for portable systems (vs. SP3232EHEP)
- Supports higher RS-232 throughput than conventional low-speed serial links (vs. MAX3221IPWR)
Designhinweise
Place the 0.1 µF charge-pump capacitors directly beside the pins and circuit identified in the MaxLinear data sheet. Keep these high-current switching loops compact and route them away from receiver inputs and sensitive analog sections. In addition to schematic equivalence, verify capacitor voltage rating, dielectric tolerance, and effective DC-bias derating because compact ceramic capacitors can lose substantial capacitance at the working voltage.
Separate the logic-side and RS-232-side nets clearly in the layout. Keep the exposed connector and protection network away from the transceiver and host controller, and provide a low-impedance return path for cable currents. The RS-232 drivers produce a large voltage swing relative to the 3.3 V logic domain, so generous spacing and minimized connector-side copper help limit capacitive coupling into adjacent circuits.
Do not assume that the 460 kbps signaling rate guarantees reliable communication over an arbitrary cable length. RS-232 is point-to-point, and baud rate, cable capacitance, grounding, connector geometry, and the data protocol must be considered together. Use the manufacturer data sheet for signal timing and logic levels, and validate startup, shutdown, and repeated communication over the intended cable and connector configuration.
Compliance-Informationen
The device is a general-purpose RS-232 interface IC for portable and hand-held equipment, so AEC-Q100 qualification is not indicated. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the applicable manufacturer documentation.