SP3232EUCA-L - 3.3V 1Mbps RS-232 IC | MaxLinear
Teilenummer: SP3232EUCA-L ✗ AbgekündigtSP3232EUCA-L Übersicht
An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 line levels and converts received RS-232 signals back into digital logic. The SP3232EU belongs to the broader line-driver and line-receiver hierarchy, where the line driver transmits, the line receiver detects, and the transceiver combines both functions. It is particularly relevant to portable and handheld equipment requiring bidirectional asynchronous serial communication.
The principal features include two transmit drivers, two receive receivers, full RS-232 operation, a 3.3 V supply, and a maximum data transmission rate of 1000 kbps. The 1000 kbps rating supports high-speed RS-232 links, while the two-driver and two-receiver arrangement allows two serial channels or a combination of independent transmit and receive paths. The 16-SSOP package also supports compact board layouts where a larger SOIC footprint would be undesirable.
The internal high-efficiency charge pump generates the bipolar voltage required by the RS-232 drivers without requiring an external negative supply. According to the MaxLinear SP3232EU product information, 3.3 V operation requires only 0.1 µF charge-pump capacitors. This architecture simplifies system partitioning, although the external capacitor selection, placement, and tolerance still influence driver amplitude and signal integrity.
Typical uses include portable data terminals, handheld test equipment, industrial serial adapters, embedded serial consoles, and compact peripheral interfaces. The two transmitters and two receivers are useful when a design needs more than one RS-232 direction, while the 1000 kbps capability can accommodate short-distance high-speed links when the connected equipment, cable, and protocol support that rate.
PCB design should follow the manufacturer pin and capacitor-placement guidance, keep charge-pump and receiver-network components close to the device, and provide adequate return paths for both supply rails. The RS-232 interface must also be evaluated for ground offset, cable length, connector protection, and transient immunity; a high logic data rate does not guarantee reliable communication on every cable or grounding arrangement.
Drop-in-Alternativen für SP3232EUCA-L – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit SP3232EUCA-L (gleiche Bauform und Footprint) – abweichend in Package, Power-Supply Architecture, Product Type.
SP3232EUCY-L/TR
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →SP3232EUEY-L/TR
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →MAX3232EESE
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ADM3202ARUR
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
ST3232BEYR
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
SP3232EUCA-L Technische Daten
| Product Type | RS-232 transceiver IC |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Interface Standard | RS-232 |
| Versorgungsspannung | 3.3 V |
| Maximum Data Rate | 1000 kbps |
| Power-Supply Architecture | Integrated high-efficiency charge pump |
| Required Charge-Pump Capacitance | 0.1 µF in 3.3 V operation |
| Gehäuse | 16-SSOP |
| Montageart | Surface mount |
SP3232EUCA-L 16-ssop Pinbelegungsleitfaden
Pinbelegung für SP3232EUCA-L (16-ssop-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für SP3232EUCA-L.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
SP3232EUCA-L ist geeignet für 6 Anwendungs: Portable Serial Terminal, Industrial Serial Adapter, Handheld Test Instrument, Embedded Serial Console, Instrumentation Control Panel, Peripheral Data Interface.
Portable Serial Terminal
The SP3232EUCA-L suits portable terminals that require two RS-232 communication paths in a compact board area. Its two drivers and two receivers provide bidirectional capability, while the 1000 kbps data rate supports faster command and data transfers than conventional low-speed serial links. The integrated charge-pump supply reduces the number of external support components, and only 0.1 µF capacitors are required for 3.3 V operation according to the MaxLinear product information. Designers should still verify connector protection, cable length, and grounding in the final enclosure because those factors determine whether the nominal 1000 kbps signaling rate remains reliable.
Empfohlen
Industrial Serial Adapter
The SP3232EUCA-L can provide multiple RS-232 channels in an industrial adapter without requiring a separate negative supply rail. Two drivers and two receivers allow two full-duplex connections, and the 3.3 V supply operation aligns with modern embedded control systems. Its 1000 kbps maximum rate is useful for short-distance links carrying configuration, status, or diagnostic data. The charge-pump capacitors must be placed close to the interface pins, and the design should include appropriate protection at externally accessible connectors to prevent transients from reaching the receiver inputs.
Empfohlen
Handheld Test Instrument
A handheld test instrument benefits from the SP3232EUCA-L because it combines two RS-232 drivers, two receivers, and a 1000 kbps data rate in a 16-SSOP package. These functions can support communication with a host computer and an external peripheral without adding a separate negative power supply. The 3.3 V operating supply reduces power-supply complexity, while the 0.1 µF charge-pump capacitance values specified for 3.3 V operation support compact PCB layouts. Engineers should budget connector clearance and consider transmit-disable or power-control behavior when the handheld unit is connected to unpowered accessories.
Empfohlen
Embedded Serial Console
The SP3232EUCA-L is appropriate for an embedded debug or service console requiring two RS-232 channels and a compact interface section. The two transmitters support connections to two external targets, while the two receivers can monitor command acknowledgements or incoming service requests. Its 1000 kbps capability allows the firmware to use faster serial transfers than low-speed legacy links, subject to the target device's timing. The SSOP footprint helps conserve board area, but designers should follow the manufacturer's capacitor-placement layout and route the RS-232 traces away from sensitive analog or high-speed digital nodes.
Empfohlen
Instrumentation Control Panel
Instrumentation control panels can use the SP3232EUCA-L to connect computers, analyzers, or programmable test equipment through RS-232 ports. The dual-channel arrangement reduces the number of interface ICs when both a control port and a status port are needed, while 1000 kbps supports relatively rapid command exchange. Because RS-232 uses bipolar line signaling and can tolerate significant ground-potential differences in some installations, grounding and cable selection remain important. The 3.3 V supply and small charge-pump capacitors help the interface fit into densely populated control hardware.
Empfohlen
Peripheral Data Interface
The SP3232EUCA-L can serve as the legacy serial interface in a peripheral that also contains modern USB or network connectivity. Two RS-232 channels provide flexibility for a primary data link and a secondary configuration or diagnostic channel. The maximum 1000 kbps rate is appropriate for many short-distance peripheral links, while the integrated charge pump avoids an external negative supply and reduces connector-board area. Firmware should validate the remote device's baud-rate tolerance and ensure that both the logic-side ground and the RS-232 signal ground are connected according to the system grounding strategy.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für SP3232EUCA-L – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | SP3232EUCY-L/TR | SP3232EUEY-L/TR | MAX3232EESE | ADM3202ARUR | ST3232BEYR |
|---|---|---|---|---|---|---|
| Package | 16-SSOP | 16-SSOP | 16-SSOP | 16-SSOP | 16-SSOP | 16-SSOP |
| Brand | MaxLinear | MaxLinear | MaxLinear | Analog Devices | Analog Devices | STMicroelectronics |
| Transceiver Configuration | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers |
| Interface Standard | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 |
| Maximum Data Rate | 1000 kbps | 1000 kbps | 1000 kbps | 1000 kbps | 1000 kbps | 1000 kbps |
Wichtigste Unterscheidungsmerkmale
- Provides two RS-232 channels in a compact surface-mount package (vs. MAX3221IPWR)
- Supports high-speed RS-232 signaling (vs. ADM3202ARUR)
- Uses compact charge-pump capacitors in 3.3 V systems (vs. ST3232BEYR)
Designhinweise
Place the charge-pump capacitors and the associated receiver-network components directly beside their SP3232EUCA-L pins. The MaxLinear SP3232EU product information identifies 0.1 µF capacitors for 3.3 V operation, so the footprint should follow the exact capacitor arrangement in the manufacturer layout. Keep the traces short and provide a continuous ground reference beneath the interface section to minimize supply disturbance and improve return-current control.
Do not assume that a nominal 1000 kbps data rate guarantees reliable communication over every RS-232 cable. Check the cable length, conductor characteristics, connector wiring, signal-ground connection, and remote-device timing. The two transmitters and two receivers also do not automatically create two independent full-duplex ports; verify the transceiver enable and shutdown behavior and the intended sharing of each driver and receiver.
Keep the RS-232 traces away from switching nodes, high-current inductors, clocks, and sensitive analog inputs. Route the interface ground carefully to avoid sharing paths that carry large return currents. When the connector is exposed to user-accessible cabling, add protection at the connector boundary and select protection components that do not distort receiver operation or driver rise and fall times.
Compliance-Informationen
No explicit compliance certification for the exact SP3232EUCA-L ordering code was identified. AEC-Q100 is not applicable because this is an RS-232 interface IC rather than an automotive-qualified device.