STMicroelectronics

STM32L011D3P6 - 32MHz Cortex-M0+ 8KB MCU | STMicroelectronics

Teilenummer: STM32L011D3P6 ✓ Aktiv
Supported Vdss 14-TSSOP Package 32 MHz Speed 8 KB (8K x 8) Memory
MOQ: 1 |

STM32L011D3P6 Übersicht

The STMicroelectronics STM32L011D3P6 is an ultra-low-power 32-bit Arm Cortex-M0+ microcontroller with a 32 MHz maximum clock frequency, 8 KB of flash memory, and a 14-pin TSSOP package. It belongs to the STM32L0 access-line family, combining a compact general-purpose MCU architecture with low-power operation for cost-sensitive embedded products. The STM32L011D3P6 provides an economical platform for control, communication, sensing, and low-duty-cycle sensing applications.

A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals on one device. It belongs to the embedded-processing hierarchy and executes firmware that reads inputs, performs control calculations, and drives outputs. An Arm Cortex-M0+ MCU such as the STM32L011D3P6 provides a compact 32-bit RISC architecture suited to real-time control, while the STM32L0 family emphasizes low-power operation for battery-operated and energy-conscious equipment.

The STM32L011D3P6 combines its 32 MHz Cortex-M0+ core with 8 KB of flash program memory in a 14-TSSOP package. Its compact package reduces PCB footprint requirements, while the 8 KB embedded program area supports compact control firmware, boot logic, and application code. The STMicroelectronics product family description identifies reset and supply-management functions and positions the STM32L011x3/4 devices as access-line ultra-low-power microcontrollers.

The device uses the Arm Cortex-M0+ architecture, a 32-bit RISC design intended for efficient embedded instruction execution. Operating at up to 32 MHz gives designers additional timing headroom for peripheral activity, control loops, and communication tasks compared with lower-frequency microcontroller solutions. The exact RAM, peripheral configuration, voltage range, and electrical limits should be confirmed against the manufacturer documentation for the selected ordering code before schematic and firmware release.

Typical uses for the STM32L011D3P6 include low-power sensor nodes, compact industrial controllers, building-access controls, small consumer products, portable accessories, and embedded measurement modules. Its 8 KB flash budget favors applications whose firmware can remain compact, while its 32-bit processing core supports modern C-based embedded development. Low-duty-cycle operation can also help reduce energy consumption in battery-powered installations.

Designers should base PCB pin assignments and decoupling on the manufacturer pinout and application guidance for STM32L011x3/4 devices. Confirm programming, boot, reset, clock, and supply connections against the exact package variant, and validate firmware timing and peripheral use with the manufacturer’s device documentation. The 14-TSSOP footprint also requires a land pattern compatible with the specified lead pitch and body dimensions.

This product page combines the manufacturer family information with exact distributor-identifiable device attributes, package guidance, sourcing answers, and practical comparisons. It highlights the STM32L011D3P6’s 32 MHz Cortex-M0+ performance and 8 KB flash configuration while separating those confirmed facts from characteristics that require selection-specific verification.

Drop-in-Alternativen für STM32L011D3P6 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

STM32L011D4P6

✅ Drop-In
📦 14-TSSOP
32 MHz Cortex-M0+ performance and 14-TSSOP footprint are retained; flash increases from 8 KB to 16 KB (+100%)

📋 Referenzalternative (nicht im Katalog)

STM32L021D4P6

✅ Drop-In
📦 14-TSSOP
32 MHz Cortex-M0+ performance and 14-TSSOP footprint are retained; flash increases from 8 KB to 16 KB (+100%)

📋 Referenzalternative (nicht im Katalog)

STM32L011D3P6 Grenzwerte & elektrische Eigenschaften

Product Type 32-bit ultra-low-power microcontroller
Processor Core Arm Cortex-M0+
Architecture 32-bit RISC
Maximale Taktfrequenz 32 MHz
Flash Memory 8 KB (8K x 8)
Gehäuse 14-TSSOP
Package Pin Count 14 pins
Montageart Surface mount
Product Family STM32L011x3/4
Product Line STM32L0 access line
Reset and Supply Management Supported

STM32L011D3P6 14 pins Pinbelegungsleitfaden

Pinbelegung für STM32L011D3P6 (14 pins-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.

Pinbelegungsdiagramm für STM32L011D3P6 im 14 pins-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für STM32L011D3P6.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

STM32L011D3P6 ist geeignet für 6 Anwendungs: Battery-Powered Sensor Node, Industrial Control Module, Access Control Terminal, Portable Measurement Device, Smart Home Sensor Interface, Compact Consumer Appliance Controller.

🧩

Battery-Powered Sensor Node

The STM32L011D3P6 fits compact battery-powered sensor nodes that need low-power operation without the overhead of a larger microcontroller package. Its 32 MHz Arm Cortex-M0+ core provides enough timing capability for sensor sampling, control logic, and low-rate serial communication, while the 8 KB flash capacity supports a compact firmware image. The 14-TSSOP package also reduces board footprint compared with larger leaded or high-pin-count MCU packages. The principal design trade-off is flash capacity: firmware should remain within 8 KB, and any expansion or extended diagnostic functions should be evaluated against the STM32L011D4P6 upgrade before PCB release.

🏭

Industrial Control Module

The STM32L011D3P6 is suitable for compact industrial control modules that coordinate digital inputs, status indicators, and simple actuator commands. Its 32-bit Cortex-M0+ processor and 32 MHz operating frequency provide a practical balance of responsiveness and resource efficiency for deterministic control loops. The 14-pin TSSOP format supports space-constrained control boards while reducing assembly complexity compared with larger leaded packages. Because the device includes only 8 KB of flash, production firmware should be size-checked after linking, and safety margins should be reserved for diagnostics, revision identifiers, and future maintenance.

🔒

Access Control Terminal

The STM32L011D3P6 can serve as the controller in a compact access-control terminal responsible for button handling, lock or relay sequencing, status feedback, and communications with a higher-level controller. Its 32 MHz Cortex-M0+ core handles multiple real-time tasks, and the 14-TSSOP package leaves more board area for power, interface, and protection components. The ultra-low-power family positioning is also useful in installations where the terminal spends substantial time idle. Firmware must fit the 8 KB flash limit and should include fail-safe state handling for the electromechanical lock or relay during reset and power faults.

📱

Portable Measurement Device

The STM32L011D3P6 is appropriate for a portable measurement device that must combine local acquisition control, calibration logic, and a compact user interface. Operating at up to 32 MHz, the Cortex-M0+ processor can coordinate sampling timing and data conditioning while remaining in a low-power MCU family. The 14-TSSOP package supports compact, surface-mount construction, and 8 KB of flash is appropriate for tightly scoped firmware. Designers should partition code carefully and retain the source-level memory report as a release check. If the measurement application requires substantial buffering, protocol conversion, or historical data handling, the 16 KB D4 alternatives may be preferable.

🏠

Smart Home Sensor Interface

The STM32L011D3P6 works well as a smart-home sensor interface when a local microcontroller must condition inputs and package readings for a network connection. Its 32-bit processing core supports event-driven firmware, while the compact 14-TSSOP package simplifies placement beside sensors and interface circuitry. The STM32L011 family’s low-power positioning is beneficial in battery-operated endpoints that wake only to measure or report state. The 8 KB flash budget favors concise code paths, so protocol updates, diagnostics, and security-related functions must be monitored during development. A D4 family device offers additional flash margin without changing the package footprint.

🔧

Compact Consumer Appliance Controller

The STM32L011D3P6 can provide the central logic in a compact consumer appliance controller that coordinates buttons, indicators, simple sensors, and an actuator. Its 32 MHz Cortex-M0+ core supplies ample performance for deterministic state-machine control, and its 14-TSSOP package helps minimize controller-board area. The STM32L0 low-power positioning can contribute to efficient standby behavior in appliances with intermittent use. Engineering teams should reserve flash space for boot logic, error handling, and production configuration. If the product roadmap adds displays, more communication protocols, or elaborate diagnostics, the D4 alternatives provide 16 KB of flash while preserving the 14-pin package format.

Zusammenfassung der empfohlenen Produkte

STM32L011D3P6 STMicroelectronics Verwendet in: Battery-Powered Sensor Node, Industrial Control Module, Access Control Terminal, Portable Measurement Device, Smart Home Sensor Interface, Compact Consumer Appliance Controller STM32L011D4P6 Same-family upgrade with more flash Verwendet in: Battery-Powered Sensor Node, Industrial Control Module, Portable Measurement Device, Smart Home Sensor Interface STM32L021D4P6 Same-package flash-expanded option Verwendet in: Access Control Terminal, Compact Consumer Appliance Controller
What are the key specifications of STM32L011D3P6 that engineers should know?
The STM32L011D3P6 integrates a 32-bit Arm Cortex-M0+ core, 32 MHz maximum clock frequency, and 8 KB of flash memory in a 14-pin TSSOP package. According to the STMicroelectronics STM32L011D3 product page, the STM32L011x3/4 family is an ultra-low-power access-line MCU family with reset and supply-management functions. These confirmed attributes make the device suitable for compact embedded control designs where package area, processing capability, and low-power operation are important.
Where can I download the STM32L011D3P6 datasheet PDF?
The official STM32L011D3P6 documentation is available from the STMicroelectronics STM32L011D3 product page at https://www.st.com/en/microcontrollers-microprocessors/stm32l011d3.html. The page links to the device family resources and manufacturer documentation needed to confirm the electrical limits, memory organization, pin descriptions, clock settings, and peripheral functions. Use the documents associated with STM32L011x3/4 devices and verify that the ordering code corresponds to the 14-TSSOP STM32L011D3P6 variant.
Where can I find the STM32L011D3P6 pinout?
The STM32L011D3P6 pinout must be taken from the STM32L011x3/4 device documentation because the verified product information identifies the package but does not enumerate individual terminal functions. Open the manufacturer STM32L011D3 product page and use its pin-description table or package drawing to assign power, ground, reset, boot, clock, and I/O connections. Do not infer the 14 pin assignments from another STM32 series, because peripheral mapping and alternate functions can differ.
What is the STM32L011D3P6 equivalent to in the STM32L011 family?
The closest family alternatives identified by the cross-reference material are STM32L011D4P6 and STM32L021D4P6. Both preserve the STM32L011 family architecture and 14-TSSOP format, while their D4 flash configuration provides more program memory than the STM32L011D3P6. Their larger memories can be advantageous, but the increased flash capacity and any firmware implications should be reviewed before treating either part as an exact procurement substitute.
Is the STM32L011D3P6 suitable for low-power embedded devices?
Yes, the STM32L011D3P6 is suitable for low-power embedded devices because STMicroelectronics classifies the STM32L011x3/4 family as an ultra-low-power access line. The MCU combines a 32-bit Cortex-M0+ processor, 8 KB flash, and operation up to 32 MHz in a compact 14-TSSOP package. Actual current consumption depends on the operating mode, clock configuration, peripherals, and firmware duty cycle, so battery-life calculations should use the manufacturer’s mode-specific electrical data.
STM32L011D3P6 vs STM32L011D4P6 — which is better for embedded control?
STM32L011D3P6 is preferable when 8 KB of flash is sufficient, while STM32L011D4P6 is the better choice when additional program memory is needed. Both retain the STM32L011 family platform, 32 MHz Cortex-M0+ performance, and 14-TSSOP package format. The decisive difference is embedded memory capacity: the D3 device provides 8 KB, whereas the D4 configuration provides 16 KB. Consider code size, bootloader requirements, and upgrade margin before replacing one ordering code with the other.
Can STM32L011D4P6 replace STM32L011D3P6 without changing the PCB?
STM32L011D4P6 can be used as a same-package upgrade candidate because it retains the STM32L011 family platform and 14-TSSOP footprint while increasing flash memory from 8 KB to 16 KB. The larger memory provides more firmware and data space without requiring a different package land pattern. Verification should still include supply limits, clock settings, peripheral configuration, bootloader behavior, and any application-specific assumptions tied to the original ordering code.
When should I choose STM32L011D3P6 over STM32L011D4P6?
Choose STM32L011D3P6 when its 8 KB flash budget comfortably supports the final firmware and the design does not require the additional program space of the D4 variant. The lower-memory configuration may be appropriate for compact sensing, simple control, and cost-sensitive products. Select STM32L011D4P6 instead when the application, bootloader, diagnostics, or planned feature growth requires more than 8 KB of embedded flash.
What is the best drop-in replacement for STM32L011D3P6?
STM32L011D4P6 is the strongest same-brand drop-in upgrade candidate identified for STM32L011D3P6 because it maintains the STM32L011 family and 14-TSSOP package while increasing flash memory from 8 KB to 16 KB. STM32L021D4P6 is another same-package family alternative, although its additional differences should be reviewed. No cross-manufacturer device was verified as a fully pin-compatible, firmware-compatible drop-in replacement, so migration across manufacturers requires independent validation.
Is STM32L011D3P6 the same as STM32L021D4P6?
No, STM32L011D3P6 and STM32L021D4P6 are related STM32L0 devices rather than identical parts. The STM32L011D3P6 has an 8 KB flash configuration, while STM32L021D4P6 belongs to the D4 flash configuration with 16 KB. They share the 32 MHz Cortex-M0+ platform and 14-TSSOP package, but pin function, peripheral, and firmware differences must be checked in the manufacturer documentation before substituting one for the other.
Where can I buy STM32L011D3P6 online?
Use the Request a Quote form on this page to source the exact STM32L011D3P6 ordering code. The form supports a direct request for current commercial terms, quantity availability, and delivery information without presenting a stale static price. The exact manufacturer ordering code matters because STM32L011x3/4 devices include different memory and package configurations, and each ordering code identifies a specific production variant.
What is the price of STM32L011D3P6?
The current commercial price for STM32L011D3P6 should be requested through the Request a Quote form on this page. Pricing depends on order quantity, procurement volume, packaging configuration, and current component availability, so a static figure can become misleading. Submit the exact MPN, required quantity, and target delivery location to receive current sourcing terms for the 14-TSSOP device.
What is the lead time for STM32L011D3P6?
The current lead time for STM32L011D3P6 should be confirmed through the Request a Quote form on this page. Lead time can vary with quantity, requested delivery date, production scheduling, and inventory position. Include the required quantity and delivery schedule in the request so the quotation can reflect the actual procurement plan rather than a generic availability statement.
Is STM32L011D3P6 in stock?
The STM32L011D3P6 is offered for order, but current stock should be confirmed through the Request a Quote form on this page. Inventory can move quickly and can differ by package, quantity, and shipment destination. Providing the exact MPN and required quantity allows the sourcing response to identify the available supply and delivery window for your specific order.
How does the STM32L011D3P6 compare with STM32L011F4P6 for a compact design?
STM32L011D3P6 has 8 KB of flash and uses a 14-TSSOP package, whereas STM32L011F4P6 is identified as a different member of the STM32L011 family and is associated with a larger flash configuration. The D3 part is the appropriate choice when its 8 KB code budget meets the application and board area must be minimized. The F4 device should be considered when greater memory capacity is more important than the smaller 14-pin footprint.

Technische Referenzdaten für STM32L011D3P6 – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the STM32L011D3P6 for compact, low-power embedded designs whose finalized firmware fits within 8 KB of flash and require a 32 MHz Arm Cortex-M0+ processor in a 14-TSSOP package. It is well matched to simple sensing, access-control, industrial-control, smart-home, and compact consumer-appliance tasks where package area and resource efficiency matter. Select STM32L011D4P6 when the same package and Cortex-M0+ platform are desired but the application needs 16 KB of flash for additional code, diagnostics, or future growth. Consider STM32L021D4P6 when its family-specific characteristics satisfy the design and the extra 8 KB of flash is useful. No cross-manufacturer part was confirmed as a fully compatible drop-in, so a cross-brand migration would require separate electrical, pin-function, firmware, and qualification review.

Vergleich mit Alternativen

Parameter Dieses Produkt STM32L011D4P6 STM32L021D4P6
Brand STMicroelectronics STMicroelectronics STMicroelectronics
Package 14-TSSOP 14-TSSOP 14-TSSOP
Processor Core Arm Cortex-M0+ Arm Cortex-M0+ Arm Cortex-M0+
Maximum Clock Frequency 32 MHz 32 MHz 32 MHz
Flash Memory 8 KB (8K x 8) 16 KB 16 KB
Architecture 32-bit RISC 32-bit RISC 32-bit RISC
Power Class Ultra-low-power Ultra-low-power Ultra-low-power

Wichtigste Unterscheidungsmerkmale

  • Lower flash configuration provides a defined 8 KB resource target (vs. STM32L011D4P6)
  • Same package and core preserve hardware reuse (vs. STM32L021D4P6)
  • Compact 14-pin package for space-constrained designs (vs. STM32L011F4P6)

Designhinweise

Use the manufacturer’s STM32L011x3/4 package drawing to create the 14-TSSOP land pattern, and place the MCU close to its supply and decoupling connections. Keep the footprint dimensions tied to the lead pitch and body outline of the selected ordering code. Confirm every power, ground, reset, boot, clock, programming, and I/O connection against the exact pin-description table before releasing the PCB artwork.

The STM32L011D3P6 belongs to an ultra-low-power MCU family, but final energy consumption depends on clock selection, operating mode, peripheral activity, and firmware wake frequency. Build power budgets from the manufacturer’s mode-specific current data and include all board loads in system calculations. For battery-operated designs, measure the complete assembled product rather than relying only on the MCU’s active current.

Do not treat the STM32L011D3P6, STM32L011D4P6, and STM32L021D4P6 as identical devices merely because they use the same family and package. The target has 8 KB of flash, while the identified alternatives have 16 KB. Recheck memory limits, peripheral assignments, startup behavior, and application assumptions whenever the ordering code changes, and validate production firmware with a linker memory report.

Preserve access to programming and reset signals when placing the 14-TSSOP device. Route sensitive timing or communication signals away from noisy switching nodes, and keep the return path for supply current short. Since the exact peripheral mix and electrical limits are not repeated here, use the manufacturer schematic recommendations for decoupling and signal conditioning associated with the exact STM32L011x3/4 configuration.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The verified product information identifies the STM32L011D3P6 as an STM32L0 access-line MCU but does not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. Use the manufacturer’s current product documentation and declarations for compliance verification.

Daten verifiziert am: 2026-11-14 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

STM32L011D3P6 datasheet STM32L011D3P6 pinout STM32L011D3P6 datasheet pdf STM32L011D3P6 specifications STM32L011D3P6 14-TSSOP STM32L011D3P6 equivalent STM32L011D3P6 replacement STM32L011D3P6 cross reference STM32L011D3P6 vs STM32L011D4P6 STM32L011D3P6 footprint STM32L011D3P6 application circuit STM32L011D3P6 price STM32L011D3P6 stock STMicroelectronics STM32L011D3P6 STM32L011D3P6 low power microcontroller

Verwandte Bauteile & Begriffe

STMicroelectronics STM32L011D3P6 STM32L011D4P6 STM32L021D4P6 STM32L011F4P6 STM32L011x3/4 STM32L0 Arm Cortex-M0+ 32-bit RISC core microcontroller embedded processor semiconductor 14-TSSOP TSSOP package family surface mount 8 KB flash memory 32 MHz clock frequency ultra-low-power MCU reset management supply management industrial control battery-powered sensor node smart-home sensor interface access-control terminal compact consumer appliance
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen